INFINITY ® Residential Elevator Roped Hydraulic Residential Elevator Planning Guide ASME A17.1 - 2000 Part 5 Section 5.3 CAN/CSA B44 - 2000 Part 5 Section 5.
INFINITY Residential Elevator Introduction This planning guide is designed to assist architects, contractors, home owners and elevator professionals in planning for an INFINITY Residential Elevator to meet the requirements of ASME A17.1 Part 5, Section 5.3 and CAN/CSA B44 Part 5, Section 5.3.
INFINITY Equipment for Residential Elevator Residential Elevator This elevator meets the requirements of ASME A17.1 Part 5, Section 5.3 and CAN/CSA B44 Part 5, Section 5.3 for a Residential Elevator General Safety Devices Rated Load: 750 lbs. (340kg) or 1000 lbs. (454kg) Nominal Speed: 36 fpm (.
INFINITY Hoistway and Cab Configurations Residential Elevator Choice of Five Variations Important Note: Finished hoistway dimensions must include the drywall. Determine the fire rating of the hoistway, the type and layers of sheet rock and build only off shop drawings specific to your project.
INFINITY Hoistway and Cab Configurations Type 5 (S) - Enter/Exit Same Side (Opposite Sling) Residential Elevator Diagram of Elevator Shaft Overhead Elevator Guide Rails LENGTH WIDTH Hydraulic Lifting Cylinder 3/8" Wire Rope Cable Elevator Cab Cab Operating Panel see chart Clear Cab Length 48" 54" 60" X Finished Side Entrance Hoistway Length Center Lines 54 1/4" 60 1/4" 66 1/4" X + 6 1/2" Cab Gate 27 1/8" 30 1/8" 33 1/8" (X + 6 1/4") / 2 Pit Hoistway Overhead Clearance Infinity Cab Height Over
INFINITY Specifications for Part 5.3 Compliance Residential Elevator PART 1 - GENERAL PART 2- PREPARATORY WORK BY OTHERS SCOPE 2.1 The following preparatory work to accommodate/receive the elevator is to be done by others. To furnish all labor, materials and equipment necessary or required to fully complete the installation of the elevator as indicated on the Drawings and Specifications.
Continued Specifications for Part 5.3 Compliance PART 4 – PRODUCT DATA 4.1 MANUFACTURER/PRODUCT The elevator shall be the CONCORD INFINITY Residential Elevator manufactured by Concord Elevator Inc. Toll Free (800) 661-5112 and (905) 791-5555, Fax (905) 791-2222 Dealer Name ___________________________________ Number _______________________________________ Rated Load: 750 lbs. (340 kg.) Nominal Speed: 36-fpm (0.
INFINITY Specifications for Part 5.3 Compliance Continued Residential Elevator 4.10 CABLE Minimum of two 3/8" (10 mm) IWRC Galvanized Aircraft Cables. Minimum breaking strength of 14,400 lbs. each. 4.15.3 Guides shall be bolted through the hoistway enclosure with back-up plates, washers and nuts. Subject to architects’ alterations and approval. 4.
Wood Hoistway Construction INFINITY Residential Elevator Suggested Support Wall Wood Construction Note: The drawings on this page are for reference only. Building structural engineer to ensure that the building and hoistway will support all loads imposed by the lift equipment. Fire rating of hoistway is subject to local building codes. CPG-INFVER01 © 2004, Concord Elevator Inc.
INFINITY Wood Construction Sectional View Wood Construction Plan View Residential Elevator Rail Bracket CPG-INFVER01 © 2004, Concord Elevator Inc.
INFINITY Masonry Construction Elevation View Residential Elevator (See Note 1) BLOCK WALL (8" MINIMUM) Masonry Construction Plan View Rail Bracket Note: For 8" Block Use Thru Bolts CPG-INFVER01 © 2004, Concord Elevator Inc.
INFINITY Elevator Rail Support Wall Residential Elevator Drawing Notes 1 See Elevator Drawing for rail bracket spacing and pit depth. 2 Wall lateral support spacing: - for 2" x 4" studs, use 6' -10" (2090 mm) max. - for 2" x 6" studs, use 13' -6" (4120 mm) max. 3 Sheathing installation: install sheets vertically full width of shaft or min. centred on rail brackets. 4 Connectors to resist horizontal load but allow vertical movement. For Wood, use 2" x ¼" cap screw lag bolts.
