Installation Sheet

ManualsBrandsInfinity Drain ManualsPlumbingWedgeWire 5" Drain Grate with Throat Center Drain Kit

Bonded Flange

Center Drain Series

Installation Instructions

The Bonded Flange Center Drain Series are intended for use

with the following waterproong methods:

Liquid Waterproofing

Fabric Waterproofing

Dimension are subject to Manufacturers tolerance and change without notice. We can assume no responsibility for

use of superseded or void data.

Las dimensiones están sujetos a la tolerancia del fabricante y cambio sin previo aviso. No podemos asumir ninguna

responsabilidad por el uso de datos a sustituir los nulos.

Infinity Drain • 18 Secatoag Avenue, Port Washington, New York 11050

Phone 516.767.6786 • Fax 516.740.3066 • www.InfinityDrain.com

Made in the U.S.A.

LTD 5 B

TDB 15

RTDB 15

TDB 20

Summary of content (6 pages)

PAGE 1
Bonded Flange Center Drain Series Installation Instructions LTD 5 B RTDB 15 TDB 15 TDB 20 The Bonded Flange Center Drain Series are intended for use with the following waterproofing methods: ° Liquid Waterproofing ° Fabric Waterproofing Made in the U.S.A. Infinity Drain • 18 Secatoag Avenue, Port Washington, New York 11050 Phone 516.767.6786 • Fax 516.740.3066 • www.InfinityDrain.com Dimension are subject to Manufacturers tolerance and change without notice.
PAGE 2
Series Components: LTD 5 B Series RTDB 15 Series LT5-2 SS 5" x 5" Strainer Only with Satin Stainless Finish RT 15 B 5" Round Tile Drain Strainer LT5-2 PS 5" x 5" Strainer Only with Polished Stainless Finish BFA 42 Bonded Flange ABS Drain BFA 22 Bonded Flange ABS Drain BFP 42 Bonded Flange PVC Drain BFP 22 Bonded Flange PVC Drain TDB 15 Series TDB 20 Series T15 A SS 5" x 5" Strainer Only with Satin Stainless Finish T20 A SS 8" x 8" Strainer Only with Satin Stainless Finish T15 A PS 5" x 5"
PAGE 3
(A) Strainer (B) Throat Liquid/Fabric Waterproofing (C) Bonded Flange Drain Body BFA/BFP (C1) (C2) Installation Instalación 1. Set bonded flange into a wet pre laid bed of mortar and allow bonded flange drain body (C) to recess into subfloor. Connect the drain body (C) to existing waste line using PVC cement or ABS pipe cement.
PAGE 4
. When mortar layer is dry, perform necessary waterproofing (Liquid /Fabric Waterproofing) as per local code. Ensure waterproofing layer reaches the edge of the hole in the drain body (C2). 4. Cuando el mortero este seco, realice necesario impermeabilización (Liquida/ Tela impermeabilización) según las normas locales. Asegure que la capa de impermeabilización alcance el borde del agujero en el cuerpo del desagüe (C2).
PAGE 5
7. Using desired floor material, mark the thickness of the material along the outside of the throat (B), so that it will finish 1/16” above the channel. Spread thinset/mortar bed up to the marked thickness. Ensure this bed is pitched all directions toward the center drain. If using a mortar build up, apply a bead of silicone caulk around the throat after mortar is dry. Lay finishing material, and have material finish to the edge of the throat (B).
PAGE 6