Specification Sheet

ManualsBrandsInfinity Drain ManualsPlumbing60" Site Sizable Linear Drain S-PVC Low Profile Complete Kit with 1-1/2" Perforated Offset Slot Grate

S-LT 38 Series

LOW PROFILE

SITE SIZABLE PVC

▪ S-LT 3836 - 36” Complete Kit

▪ S-LT 3848 - 48” Complete Kit

▪ S-LT 3860 - 60” Complete Kit

▪ S-LT 3872 - 72” Complete Kit

▪ S-LT 3896 - 96” Complete Kit

Features

▪ Modify length and outlet location on site

▪ Indoor or outdoor use

▪ Low proﬁ le 1” Height

▪ 16 gauge, 304L stainless steel perforated grate

▪ Works with 2” clamp down ﬂ oor with 2” throat/strainer size

(not included)

▪ NOT INTENDED for installation across a barrier-free threshold

▪ Compatible with: PVC Liner, Rubber Liner (Chloraloy ®), Hot

Mop, Lead Pan, Copper Pan, or Fiberglass

▪ Flow rate - 9 gpm per outlet

▫ Flow rate measured at outlet only. Measurement does not account

for water in channel or sheeting on shower ﬂ oor.

▫ Additional outlets can be added and combined into a larger waste

line to increase ﬂ ow rates

Installation

Care & Maintenance

S-LT 38 stainless steel linear drain top grates are made of 304L stainless steel. This material is non-porous, hygienic, rust-free and extremely

durable. Bar Keepers Friend® and Soft Scrub® are commonly available products that can be used to protect and clean your Satin Stainless drain

cover. For stains that have been left for an excessive amount of time, stronger cleaning agents such as Steel Brite Cleaner may be needed. For

Polished Stainless and other ﬁ nishes we recommend a mild soap and a soft cloth for cleaning. DO NOT use any abrasive cleaners, scrub pads or

allow household cleaning agents, such as bleach, to sit on the drain cover for a long period of time. Stainless steel does not rust. External factors,

such as contamination from other highly ferrous metals, built up road salt, sea salt, or chlorine may have caused ”surface” rust which can be

removed using Barkeepers Friend®, Soft Scrub®, or Steel Brite Cleaner. Always follow the directions on the bottle. Follow proper maintenance

procedures to prevent excessive surface rust. In areas of frequent exposure to salt, chlorine, and other chemical compounds, maintenance of

the stainless grates should be performed at least 2-3 times per year.

Page 1 of 4FM530-12-19

Dimensions are subject to manufacturers tolerance and change without notice. We can assume no responsibility for use of superceded or void data.

Inﬁ nity Drain

145 Dixon Avnue

Amityville, NY 11701

Phone: 516.767.6786

Fax: 516.740.3066

www.Inﬁ nitydrain.com

NOTE: Installer must verify all rough-in

dimensions prior to installation and consult

local and national codes. Conformity and com-

pliance to local and national codes are the

responsibility of the installer.

Summary of content (4 pages)

PAGE 1
▪ ▪ ▪ ▪ ▪ S-LT 38 Series LOW PROFILE SITE SIZABLE PVC S-LT 3836 - 36” Complete Kit S-LT 3848 - 48” Complete Kit S-LT 3860 - 60” Complete Kit S-LT 3872 - 72” Complete Kit S-LT 3896 - 96” Complete Kit Features ▪ Modify length and outlet location on site ▪ Low proﬁle 1” Height ▪ Works with 2” clamp down ﬂoor with 2” throat/strainer size ▪ Indoor or outdoor use ▪ 16 gauge, 304L stainless steel perforated grate (not included) ▪ NOT INTENDED for installation across a barrier-free threshold ▪ Comp
PAGE 2
B A 1 B S-LT 3836 S-LT 3848 S-LT 3860 A 15 1 16 " 1 SECTION 1-1 1 12" B 1 1 14" 1 12" 1 2" KA 38 PERFORATED SLOT PATTERN GRATE 1 3" CT CHANNEL TRIM HS 2 HAIR STRAINER GL 38 CHANNEL 1 **SUPPLIED IN ONE FULL LENGTH EL 38 PVC END STOP 3 34" SL 32 OUTLET SECTION S 50 PVC THREADED OUTLET SECTION 1-1 2" CLAMP DOWN DRAIN ASSEMBLY (MATERIAL CAN BE CAST IRON, ABS, OR PVC) KA 38 PERFORATED SLOT PATTERN GRATE Model Number □ Complete Kit Contents 1 - KA 3836 Stainless Steel Grate 1 - GL 38
PAGE 3
A S-LT 3872 S-LT 3896 15 1 16 " B 1 12" A A 1 14" B 1 1 12" B 2" 1 1 3" 1 SECTION 1-1 1 SECTION 1-1 3 34" 1 SECTION 1-1 KA 38 PERFORATED SLOT PATTERN GRATE KA 38 PERFORATED SLOT PATTERN GRATE HS 2 HAIR STRAINER KA 38 PERFORATED SLOT PATTERN GRATE HS 2 HAIR STRAINER EL 38 PVC END STOP EL 38 PVC END STOP GL 38 CHANNEL **SUPPLIED IN ONE FULL LENGTH GL 38 CHANNEL HS 2 HAIR STRAINER **SUPPLIED IN ONE FULL LENGTH EL 38 PVC END STOP S 50 PVC THREADED OUTLET GL 38 CHANNEL S 50 PVC TH
PAGE 4
ADDITIONAL INFORMATION Against a Wall Installation Threshold Installation For threshold installs, we recommend the drain run exactly wall-to-wall to block any water from leaving the shower or wet area. We do not recommend thinner or tile-in type drains for threshold installations due to the lack of channel width needed to suﬃciently catch the water.