Installation Sheet

ManualsBrandsInfinity Drain ManualsPlumbing5" x 5" Center Drain LT5 Tile Drain Strainer, and 2" Throat

Center Drain Series

Installation Instructions

The Center Drain Series are intended for use with the following waterproong methods:

Hot Mop

Copper Pan

CPE Rubber Liner (Chloraloy

)

PVC Liner

Lead Pan

Fiberglass

Dimension are subject to Manufacturers tolerance and change without notice. We can assume no responsibility for

use of superseded or void data.

Las dimensiones están sujetos a la tolerancia del fabricante y cambio sin previo aviso. No podemos asumir ninguna

responsabilidad por el uso de datos a sustituir los nulos.

Infinity Drain • 145 Dixon Avenue, Amityville, New York 11701

Phone 516.767.6786 • Fax 516.740.3066 • www.InfinityDrain.com

Made in the U.S.A.

Squares

Criss-Cross

Wedge Wire

WD 4

WD 5

LW 5

L5-2

LW5-2

LTD 5

LT5-2

LTD5-2

RTD 15

RTD 15-2

RTD 15-3

TD 15

TD 15-2

TD 15-3

TD 20

TD 20-2

TD 20-3

Moor

MD 4

MD 5

Link

KD 4

KD 5

Weave

VD 4

VD 5

Lines

ND 4

ND 5

QD 4

QD 5

XD 4

XD 5

Summary of content (6 pages)

PAGE 1
Center Drain Series Installation Instructions LTD 5 TD 15 RTD 15 RTD 15-2 RTD 15-3 LT5-2 LTD5-2 Wedge Wire LW 5 Squares MD 4 MD 5 Criss-Cross QD 4 QD 5 Weave Link KD 4 KD 5 TD 20-2 TD 20-3 TD 15-2 TD 15-3 L5-2 LW5-2 WD 4 WD 5 Moor TD 20 XD 4 XD 5 Lines VD 4 VD 5 ND 4 ND 5 The Center Drain Series are intended for use with the following waterproofing methods: ® ° Hot Mop ° Copper Pan ° CPE Rubber Liner (Chloraloy ) ° PVC Liner ° Lead Pan ° Fiberglass Made in the U.S.A.
PAGE 2
Series Components: LTD 5 Series RTD 15 Series LT5-2 SS 5" x 5" Strainer Only with Satin Stainless Finish RT 15A 5" Round Tile Drain Strainer LT5-2 PS 5" x 5" Strainer Only with Polished Stainless Finish CDI 42 4" Throat x 2" Outlet Clamp Down Drain Cast Iron CDI 22 Clamp Down Drain Cast Iron CDI 43 4" Throat x 3" Outlet Clamp Down Drain Cast Iron CDA 22 Clamp Down Drain ABS CDA 42 4" Throat x 2" Outlet Clamp Down Drain ABS CDP 22 Clamp Down Drain PVC CDA 43 4" Throat x 3" Outlet Clamp Dow
PAGE 3
Section A-A TD 15 Section A-A TD 20 Section A-A RTD 15 5" Section A-A LTD 5 C 7 38" 1 22" Section A-A LW 5 3 16 " 1 5 8" 7 4 " 8 1 22" 7 6 16 " 1 7 6 16 " SECTION 1-1 SECTION 1-1 Section A-A 5” x 5” Center Drain Section A-A 4” x 4” Center Drain 3 3 16 "
PAGE 4
KEY (A) Strainer (B) Throat Waterproofing Membrane (C) Clamp Down Drain Assembly CDI22/CDA22/CDP22/ CDI42/CDA42/CDP42/ CDI43/CDA43/CDP43 (C1) (C2) Installation Instalación 1. Connect the clamp down drain assembly (C) to existing waste line via no-hub rubber coupling, PVC cement, or ABS pipe cement and allow drain body (C2) to recess into subfloor. Ensure that drain assembly (C) is level. Unscrew and remove top clamp down plate (C1) from drain body (C2). 1.
PAGE 5
4. Reattach the top clamp down plate (C1) to the clamp down drain body (C2) over the waterproofing layer using bolts. Thread the throat (B) of the drain into top clamp down plate (C1). Adjust to the desired height. Turn clockwise to lower, counter-clockwise to raise. When determining desired height, include thickness of mortar, thinset and finishing material. 4. Vuelva a colocar la parte superior de la placa (C1) al drenaje (C2) sobre la capa de impermeabilización usando tornillos.
PAGE 6
Before finishing material Antes que el material esté terminado After finishing material 6. LTD 5/RTD 15/TD15/TD20 SERIES ONLY: Spread a layer of mortar into the strainer (A), allowing for thinset and finishing material to finish 1/16” above the metal frame. Allow to dry, spread thinset and lay material. Place top strainer (A) into the throat (B) of the drain. Después que el material esté terminado 6.