Datasheet

IRFS3004-7PPbF
2 www.irf.com
Notes:
 Calculated continuous current based on maximum allowable junction
temperature. Bond wire current limit is 240A. Note that current
limitations arising from heating of the device leads may occur with
some lead mounting arrangements. (Refer to AN-1140)
 Repetitive rating; pulse width limited by max. junction
temperature.
 Limited by T
Jmax
, starting T
J
= 25°C, L = 0.01mH
R
G
= 25Ω, I
AS
= 240A, V
GS
=10V. Part not recommended for use
above this value .
S
D
G
 I
SD
≤ 240A, di/dt ≤ 740A/µs, V
DD
≤ V
(BR)DSS
, T
J
≤ 175°C.
 Pulse width ≤ 400µs; duty cycle ≤ 2%.
 C
oss
eff. (TR) is a fixed capacitance that gives the same charging time
as C
oss
while V
DS
is rising from 0 to 80% V
DSS
.
 C
oss
eff. (ER) is a fixed capacitance that gives the same energy as
C
oss
while V
DS
is rising from 0 to 80% V
DSS
.
 When mounted on 1" square PCB (FR-4 or G-10 Material). For recom
mended footprint and soldering techniques refer to application note #AN-994.
 R
θ
is measured at T
J
approximately 90°C.
 R
θJC
value shown is at time zero.
Static @ T
J
= 25°C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Units
V
(BR)DSS
Drain-to-Source Breakdown Volta
g
e 40 ––– ––– V
∆
V
(BR)DSS
/
∆
T
J
Breakdown Volta
g
e Temp. Coefficient ––– 0.038 ––– V/°C
R
DS(on)
Static Drain-to-Source On-Resistance ––– 0.90 1.25
mΩ
V
GS(th)
Gate Threshold Volta
g
e 2.0 ––– 4.0 V
I
DSS
Drain-to-Source Leaka
g
e Current ––– ––– 20 µA
––– ––– 250
I
GSS
Gate-to-Source Forward Leaka
g
e ––– ––– 100 nA
Gate-to-Source Reverse Leaka
g
e ––– ––– -100
R
G
Internal Gate Resistance ––– 2.0 ––– Ω
Dynamic @ T
J
= 25°C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Units
g
fs Forward Transconductance 1300 ––– ––– S
Q
g
Total Gate Char
g
e ––– 160 240 nC
Q
gs
Gate-to-Source Char
g
e ––– 42 –––
Q
gd
Gate-to-Drain ("Miller") Char
g
e ––– 65 –––
Q
sync
Total Gate Char
g
e Sync. (Q
g
- Q
gd
)
––– 95 –––
t
d(on)
Turn-On Delay Time ––– 23 ––– ns
t
r
Rise Time ––– 240 –––
t
d(off)
Turn-Off Delay Time ––– 91 –––
t
f
Fall Time ––– 160 –––
C
iss
Input Capacitance ––– 9130 ––– pF
C
oss
Output Capacitance ––– 2020 –––
C
rss
Reverse Transfer Capacitance ––– 990 –––
C
oss
eff. (ER)
Effective Output Capacitance (Energy Related)
––– 2590 –––
C
oss
eff. (TR)
Effective Output Capacitance (Time Related)
––– 2650 –––
Diode Characteristics
Symbol Parameter Min. Typ. Max. Units
I
S
Continuous Source Current ––– –––
400
A
(Body Diode)
I
SM
Pulsed Source Current ––– ––– 1610 A
(Body Diode)
V
SD
Diode Forward Volta
g
e ––– ––– 1.3 V
t
rr
Reverse Recovery Time ––– 49 ––– ns
T
J
= 25°C V
R
= 34V,
––– 51 –––
T
J
= 125°C I
F
= 240A
Q
rr
Reverse Recovery Char
g
e ––– 37 ––– nC
T
J
= 25°C
di/dt = 100A/µs
––– 41 –––
T
J
= 125°C
I
RRM
Reverse Recovery Current ––– 3.2 ––– A
T
J
= 25°C
t
on
Forward Turn-On Time Intrinsic turn-on time is ne
g
li
g
ible (turn-on is dominated by LS+LD)
I
D
= 240A
R
G
= 2.7Ω
V
GS
= 10V
V
DD
= 26V
I
D
= 180A, V
DS
=0V, V
GS
= 10V
T
J
= 25°C, I
S
= 195A, V
GS
= 0V
integral reverse
p-n junction diode.
Conditions
V
GS
= 0V, I
D
= 250µA
Reference to 25°C, I
D
= 5mA
V
GS
= 10V, I
D
= 195A
V
DS
= V
GS
, I
D
= 250µA
V
DS
= 40V, V
GS
= 0V
V
DS
= 40V, V
GS
= 0V, T
J
= 125°C
MOSFET symbol
showing the
V
DS
=20V
Conditions
V
GS
= 10V
V
GS
= 0V
V
DS
= 25V
ƒ = 1.0 MHz, See Fig. 5
V
GS
= 0V, V
DS
= 0V to 32V , See Fig. 11
V
GS
= 0V, V
DS
= 0V to 32V
Conditions
V
DS
= 10V, I
D
= 195A
I
D
= 180A
V
GS
= 20V
V
GS
= -20V