Datasheet
IR2136(2)(3)(5)(6)(7)(8)
(
J&S) & (PbF
)
2 www.irf.com
Recommended Operating Conditions
The Input/Output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recom-
mended conditions. All voltage parameters are absolute referenced to COM. The V
S
offset rating is tested with all supplies
biased at 15V differential.
V
B1,2,3
High side floating supply voltage IR2136(8) V
S1,2,3
+
10 V
S1,2,3
+
20
IR21362 V
S1,2,3
+
11.5 V
S1,2,3
+
20
IR2136(3)(5)(6)(7) V
S1,2,3
+
12 V
S1,2,3
+
20
V
S1,2,3
High side floating supply offset voltage Note 1 600
V
HO1,2,3
High side output voltage V
S1,2,3
V
B1,2,3
V
LO1,2,3
Low side output voltage 0 V
CC
V
CC
Low side and logic fixed supply voltage IR2136(8) 10 20
IR21362 11.5 20
IR2136(3)(5)(6)(7) 12 20
V
SS
Logic ground -5 5
V
FLT
FAULT output voltage V
SS
V
CC
V
RCIN
RCIN input voltage V
SS
V
CC
Symbol Definition Min. Max. Units
V
Note 1: Logic operational for V
S
of COM -5V to COM +600V. Logic state held for V
S
of COM -5V to COM -V
BS
.
(Please refer to the Design Tip DT97-3 for more details).
Note 2: All input pins and the ITRIP pin are internally clamped with a 5.2V zener diode.
Symbol Definition Min. Max. Units
V
S
High side offset voltage V
B1,2,3
- 25 V
B1,2,3
+ 0.3
V
BS
High side floating supply voltage -0.3 625
V
HO
High side floating output voltage V
S1,2,3
- 0.3 V
B1,2,3
+ 0.3
V
CC
Low side and logic fixed supply voltage -0.3 25
V
SS
Logic ground V
CC
- 25 V
CC
+ 0.3
V
LO1,2,3
Low side output voltage -0.3 V
CC
+ 0.3
V
IN
Input voltage LIN,HIN,ITRIP, EN, RCIN V
SS
- 0.3 lower of
(V
SS
+ 15) or
V
CC
+ 0.3)
V
FLT
FAULT output voltage V
SS
- 0.3 V
CC
+ 0.3
dV/dt Allowable offset voltage slew rate — 50 V/ns
P
D
Package power dissipation @ T
A
≤ +25°C (28 lead PDIP) — 1.5
(28 lead SOIC) — 1.6
(44leadPLCC) — 2.0
Rth
JA
Thermal resistance, junction to ambient (28 lead PDIP) — 83
(28 lead SOIC) — 78
(44 lead PLCC) — 63
T
J
Junction temperature — 150
T
S
Storage temperature -55 150
T
L
Lead temperature (soldering, 10 seconds) — 300
V
°C/W
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters
are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured under board
mounted and still air conditions.
W
°C