Datasheet

ManualsBrandsINFINEON TECHNOLOGIES ManualsPMICsPMIC - gate/half-bridge gate drivers Inductive DMOS P TO263 15

BTM7750G

TrilithIC

Data Sheet, Rev. 1.0, June 2007

Automotive Power

Summary of content (18 pages)

PAGE 1
Data Sheet, Rev. 1.
PAGE 2
BTM7750G Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 2.1 2.2 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin Assignment . . .
PAGE 3
TrilithIC 1 BTM7750G Overview Features • • • • • • • • • • • • • • • • Quad D-MOS switch driver Free configurable as bridge or quad-switch Optimized for DC motor management applications Low RDS ON High side: 70 mΩ typ. @ 25°C,180 mΩ max. @ 150°C Low side: 45 mΩ typ. @ 25°C, 105 mΩ max. @ 150°C Maximum peak current: typ. 12 A @ 25 °C Very low quiescent current: typ.
PAGE 4
BTM7750G 2 Pin Configuration 2.1 Pin Assignment DL1 1 28 DL1 IL1 2 27 SL1 DL1 3 26 SL1 N.C. 4 25 DL1 DHVS 5 24 DHVS GND 6 23 SH1 IH1 7 LS-Leadframe 22 SH1 HS-Leadframe ST 8 21 SH2 IH2 9 20 SH2 DHVS 10 19 DHVS N.C. 11 18 DL2 LS-Leadframe Figure 1 Data Sheet DL2 12 17 SL2 IL2 13 16 SL2 DL2 14 15 DL2 Pin Assignment BTM7750G (Top View) 4 Rev. 1.
PAGE 5
BTM7750G Table 1 Pin Definitions and Functions Pin No. Symbol Function 1, 3, 25, 28 DL1 Drain of low-side switch1, lead frame 1 1) 2 IL1 Analog input of low-side switch1 4 N.C. not connected 5, 10, 19, 24 DHVS Drain of high-side switches and power supply voltage, lead frame 2 1) 6 GND Ground 7 IH1 Digital input of high-side switch1 8 ST Status of high-side switches; open Drain output 9 IH2 Digital input of high-side switch2 11 N.C.
PAGE 6
BTM7750G 2.
PAGE 7
BTM7750G 3 Block Diagram DHVS 5,10,19,24 8 ST Diagnosis IH1 7 Biasing and Protection Gate Driver RO1 IH2 9 RO2 Gate Driver 20,21 SH2 12,14,15,18 6 DL2 GND 22,23 1,3,25,28 Protection 2 IL1 SH1 DL1 Gate Driver Protection 13 Gate Driver IL2 26,27 SL1 Figure 3 Data Sheet 16,17 SL2 Block Diagram BTM7750G 7 Rev. 1.
PAGE 8
BTM7750G 4 Circuit Description 4.1 Input Circuit The control inputs IH1,2 consist of TTL/CMOS compatible Schmitt-Triggers with hysteresis. Buffer amplifiers are driven by these stages and convert the logic signal into the necessary form for driving the power output stages. The inputs are protected by ESD clamp-diodes. The inputs IL1 and IL2 are connected to the internal gate-driving units of the N-channel vertical power-MOS-FETs. 4.
PAGE 9
BTM7750G Table 3 Truth table and Diagnosis (valid only for the High-Side-Switches) Flag IH1 IH2 Inputs Normal operation; identical with functional truth table Overtemperature high-side switch1 Overtemperature high-side switch2 Overtemperature both high-side switches Under voltage SH1 SH2 ST Remarks Outputs stand-by mode switch2 active switch1 active both switches active 0 0 1 1 0 1 0 1 L L H H L H L H 1 1 1 1 0 1 X X L L X X 1 0 detected X X 0 1 X X L L 1 0 detected 0 X 1 0 1 X
PAGE 10
BTM7750G 5 Electrical Characteristics 5.1 Absolute Maximum Ratings Absolute Maximum Ratings1) – 40 °C < Tj < 150 °C Pos. Parameter Symbol Limit Values Unit Remarks min. max. VS VS(SCP) – 0.3 42 V – 28 V IS IIH VIH –7 3) A TA = 25°C; tP < 100 ms –5 5 mA Pin IH1 and IH2 – 10 16 V Pin IH1 and IH2 VST IST – 0.3 5.4 V –5 5 mA Pin ST – V 30 V – 20 V IDL VIL –7 3) A VIL = 0 V; ID ≤ 1 mA VIL = 5 V VIL = 10 V TA = 25°C; tP < 100 ms – 0.
PAGE 11
BTM7750G 5.2 Pos. Functional Range Parameter Symbol Limit Values min. max. Unit Remarks 5.2.20 Supply voltage VS VUVOFF 42 V After VS rising above VUVON 5.2.21 Input voltage HS – 0.3 15 V – 5.2.22 Input voltage LS – 0.3 10 V – 5.2.23 Status output current 0 2 mA – 5.2.24 Junction temperature VIH VIL IST Tj – 40 150 °C – Note: Within the functional range the IC operates as described in the circuit description.
PAGE 12
BTM7750G 5.4 Electrical Characteristics ISH1 = ISH2 = ISL1 = ISL2 = 0 A; – 40 °C < Tj < 150 °C; 8 V < VS < 18 V unless otherwise specified Pos. Parameter Symbol Limit Values Unit Test Condition min. typ. max. – 5 9 µA IH1 = IH2 = 0 V Tj = 25 °C – – 13 µA IH1 = IH2 = 0 V Current Consumption HS-switch 5.4.28 Quiescent current IS 5.4.29 Supply current; one HS-switch active IS – 1.65 3.3 mA IH1 or IH2 = 5 V VS = 12 V 5.4.30 Supply current; both HS-switches active IS – 3.
PAGE 13
BTM7750G ISH1 = ISH2 = ISL1 = ISL2 = 0 A; – 40 °C < Tj < 150 °C; 8 V < VS < 18 V unless otherwise specified Pos. Parameter Symbol Limit Values Unit Test Condition min. typ. max. 13 15 18 A Tj = – 40 °C – 12 – A Tj = + 25 °C 7 8.5 11 A Tj = + 150 °C RO 8 15 35 kΩ VDSL = 3 V ISCP L 21 28 34 A Tj = – 40 °C – 22 – A Tj = 25 °C 11 14 18 A Tj = 150 °C Short Circuit of high-side switch to GND 5.4.
PAGE 14
BTM7750G ISH1 = ISH2 = ISL1 = ISL2 = 0 A; – 40 °C < Tj < 150 °C; 8 V < VS < 18 V unless otherwise specified Pos. Parameter Symbol Limit Values Unit Test Condition min. typ. max. tON tOFF dV/dtON -dV/dtOFF – 85 180 µs – 80 180 µs – – 1.2 V/µs – – 1.6 V/µs – 60 150 µs – 60 150 µs 1) Switching times of high-side switch 5.4.51 Turn-ON-time to 90% VSH 5.4.52 Turn-OFF-time to 10% VSH 5.4.53 Slew rate on 10 to 30% VSH 5.4.
PAGE 15
BTM7750G 6 Application Information Note: The following simplified application examples are given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the device.
PAGE 16
BTM7750G x 8˚ ma 7.6 -0.2 1) +0.09 0.35 x 45˚ 0.23 2.65 max 2.45 -0.2 Package Outlines 0.2 -0.1 7 0.4 +0.8 1.27 0.35 +0.15 2) 28 1 10.3 ±0.3 0.1 0.2 28x 15 18.1 -0.4 1) 14 Index Marking 1) Does not include plastic or metal protrusions of 0.15 max rer side 2) Does not include dambar protrusion of 0.
PAGE 17
BTM7750G 8 Revision History Rev. Date Changes 1.0 2007-06-15 Initial Version Data Sheet 17 Rev. 1.
PAGE 18
Edition 2007-06-15 Published by Infineon Technologies AG 81726 Munich, Germany © 2007 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics.