Spider Reader Technical Manual | Spider Reader © 2020 Inepro B.V.
Spider Reader The most versatile card reader solution Congratulations on your selection of the Inepro Spider Reader. We are certain you will be pleased with your purchase of one of the flexibele solutions of the market. We want to help you get the best result from your Spider Reader. This manual contains information on how to do that; please read it carefully. Due to continuous product improvements this manual is subject to changes without notice.
Spider Reader All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher. Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks.
Table of Contents 1 3 5 7 Introduction Requirements Components Test 1 Software 2 Hardware ........................................................................................................................................................ 8 ........................................................................................................................................................ 9 11 User Interface 1 LED's ................................................................................
Directives ATTENTION!! Read this manual carefully before installing the Spider Reader! Guarentee No guarantee can be given if safety regulations are not followed. Changes and/or modifications Changes and/or modfications whch have not been approved by the responsible party can void the user's authorty to operate the equitement. Security Always disconnect the power supply before handling anything inside the device. For Indoor Use O nly This dev ice may only be used indoors.
Introduction I Part
Introduction Introduction In this manual you find the instructions to install and configure your Spider. This manual is meant for all the Inepro Spider Readers. This manual, the Spider Reader hardware and software are subject to change, make sure you have the latest version of this manual, because the older versions may have become obsolete. Function The purpose of the Spider Reader is to read the unique ID contained in the card that is presented to the reader and transfer this ID to a server.
Requirements II Part
Requirements Requirements The Spider Reader has no known requirements other than a USB host that can read a keyboard-like Human Interface Device 4 - Spider Reader
Components III Part
Components Components § P551087 - Spider Cardboard box § 200000 - Spider Reader § Spider Core Housing Top § Spider Antenna Board I § Spider Antenna Board II § Spider Core Housing Bottom § P120647 - External Spider Braille RFID Foil § P551364 - Spider Serial Stickers | Desktop sticker | EDP Sticker | 2x QR Serial sticker Check Components Please check if all the components are in the set before you continue with the installation and set-up.
Test IV Part
Test Software For the Spider there is a tools available each with its specific features. Connect the Spider to a computer or laptop and present a card to the reader. Please note that the reader needs to have the HID RAW Configuration. (See Inepro SCR-MCR-DCR RFID Programmer Tool Full Version manual for more details). Inepro SCR-MCR-DCR Programmer With this tool it is possible to change the behaviour of the card reader, by creating or editing it's configuration file.
Hardware Hardware Physical test Inepro Spider Reader 1. Connect the Inepro Spider Reader to the USB port of a computer. 2. Check the indicator LED's to see if the board is operating as it should. Blue Led burning: Reader is powered and has connection Put a card on the Spider: Besides the blue power LED, the yellow and the green LED should lit. Yellow: card detected Green: card recognised. This concludes the hardware test Version 1.0.
User Interface V Part
User Interface LED's On the USB interface board are a number of LED’s. Each of the LED's has a label, explaining their use.
Technical Specifications VI Part
Technical Specifications Specifications Power P ower Supply P ower C onsumption DC 5V 5V D C : A t maximum (depending on the configuration) 0.5 A Housing M ater ial C olour Dimensions W x D x H P C B | P C B/A BS Transparent 37.85 mm x 62.25 mm x 12.5 mm.
Troubleshooting VII Part
Troubleshooting Troubleshooting Sometimes things do not work out as expected, if so please read through this section before contacting your service organisation or dealer. Changes are you are able to solve the issue yourself. The section is set up in a Symptom - Prognosis - Resolution format, that is first the symptom is given, then the possible causes and then the resolution for those causes.
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
