User's Manual
5
6
separate the upper section from the lower section, being careful not to put stress on
the wiring harness (blue wires) connected to the solenoid valve on the upper
section. Place the tray and upper body together being careful not to pinch any
wires in the body, bring the blue wire loop back to its original position. Turn the
main on-off switch to the on position and be sure the LED lights up, then turn off.
Replace the four 6-32X1" screws and the grip panel.
CO2, Nitrogen or Compressed Air Usage
The B2K comes with a female ¼” Push-In fitting adapter on the input of the
regulator. The B2K can be set up to use a nitrogen or compressed air system.
Although it may be used, CO2 is not recommended for use as the propellant.
Generally the CO2 that we use as an industry is industrial grade CO2. It is dirty,
pumped from large tanks full of contaminates including rust and metal flakes. CO2
can be used successfully if used with anti-siphon systems and filters. Be aware that
under the conditions of CO2 the results may not be as expected. Consult the place
where you purchased your B2K, or a recognized and competent airsmith, for
instruction in the safe handling of compressed-air cylinders before purchasing or
connecting one to your B2K.
Adjustable regulator compressed air systems:
The input pressure from your compressed air system should be regulated down to
350-500 PSI output pressure. Note: on MOST systems, there is a large difference
between the setting pressure and the actual output operating pressure. If your
compressed air system does not have an output pressure gauge on its regulator we
do not recommend its use.
Fixed output regulated compressed air systems:
The B2K will work just fine with a pre-set tank. You will get better performance
from a lower output pressure than a high (750-850) output. VERIFY the output
pressure from the regulator. If your compressed air system does not have an output
pressure gauge on its regulator we do not recommend its use.
CO2 usage:
Although it may be used, CO2 is not recommended for use as the propellant.
Generally the CO2 that we use as an industry is industrial grade CO2. It is dirty,
pumped from large tanks full of contaminates including rust and metal flakes. CO2
can be used successfully if used with anti-siphon systems and filters. Be aware that
under the conditions of CO2 the results may not be as expected.
REMEMBER: CO2, compressed air or nitrogen systems can be extremely
dangerous if misused or improperly handled. Use only D.O.T. certified tanks.
Before pressurizing your B2K, check to make sure that you have a barrel plug in
place and there is no paint in the gun. The on-off switch should be OFF. Air can
now be applied, the gun will become pressurized and the bolt will move backwards.
Paintball and Loader Usage
The B2K comes equipped to accept 1.03" OD standard-gravity feed loaders. Fit the
loader directly into the vertical feed tube. Always twist it down in a CLOCKWISE
direction. Always twist it off in a CLOCKWISE direction as well. The B2K uses
.68 caliber, water-soluble paint pellets. The pellets are gravity fed from the loader
through the direct vertical feed nipple and into the breech of the gun.
Modes - Rate of Fire –
The 2003 B2K features a single mode of fire.
1. The B2K is set for Semi-auto or single shot per trigger pull mode only.
2. The cycle rate is set at 36 cycles per second.
Firing the B2K
Keep your finger out of the trigger guard and away from the trigger; point the
muzzle of your gun in a safe direction at all times during this process. Be sure your
goggles are securely in place. Push the on-off switch into the off position.
Always keep your B2K pointed in a safe direction!
1. Place the empty loader onto the gun. Be sure that it is securely mounted in
place.
2. Apply the compressed gas, pressurizing the gun.
3. Put the paintballs into the loader.
4. Remove the barrel plug.
5. Aim the gun at the target.
6. Push the on-off switch to the ON position, the LED will light up.
7. Place your finger on the trigger.
8. Pull the trigger with a smooth squeezing motion. BANG. . . .
UNLOADING THE B2K
Keep your finger out of the trigger guard and away from the trigger; point the
muzzle of your gun in a safe direction during this entire process. Always keep your
B2K pointed in a safe direction!
1. Push the on-off switch to the off position. The LED will be off.
2. Place the barrel plug into the end of the barrel.