User's Manual

ManualsBrandsIndian Creek ManualsPaintballIndian Creek B2K V1.8

INSTRUCTION MANUAL

Version 1.8

Indian Creek Design BushMaster series

Model B2K

No part of this document may be copied or reproduced in any form or by

any means without the prior written consent of Indian Creek Design, Inc.

Trademark Notices:

* Panther VTS is a registered trademark of Indian Creek Design, Inc.

* Panther II VTS is a trademark of Indian Creek Design, Inc.

* Puma is a trademark of Indian Creek Design, Inc.

* Bobcat is a trademark of Indian Creek Design, Inc.

* Thunder CAT is a trademark of Indian Creek Design, Inc.

* Desert FOX is a trademark of Indian Creek Design, Inc.

* 45/68 Magnum VTS is a trademark of Indian Creek Design, Inc.

* BushMaster 2000 is a trademark of Indian Creek Design, Inc.

* B2K is a trademark of Indian Creek Design, Inc.

* B2K2 is a trademark of Indian Creek Design, Inc.

Notice is hereby given that this manual is part of the article owned in

whole by Indian Creek Design, Inc., known as indicated in this manual

and drawings. All rights of manufacture and reproduction of such

articles or any part thereof are reserved by Indian Creek Design, Inc.

Neither said article nor any part thereof may be manufactured or

reproduced except by written authorization from Indian Creek Design,

Inc. All proprietary rights and information are the sole property of

Indian Creek Design, Inc.

Summary of content (17 pages)

PAGE 1
INSTRUCTION MANUAL Version 1.8 Indian Creek Design BushMaster series Model B2K Copyright 1993…. 2001 All Rights Reserved No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Indian Creek Design, Inc. Trademark Notices: * Panther VTS is a registered trademark of Indian Creek Design, Inc. * Panther II VTS is a trademark of Indian Creek Design, Inc. * Puma is a trademark of Indian Creek Design, Inc.
PAGE 2
STATEMENT OF LIABILITY Indian Creek Design, Inc., delivers this air gun with the understanding that Indian Creek Design, Inc., assumes no responsibility for its resale or safe handling. It can be considered a dangerous weapon if mishandled, abused, or the safety instructions are ignored. Indian Creek Design, Inc., assumes no responsibility for physical injury or property damage resulting from its use. Indian Creek Design, Inc.
PAGE 3
B2K OVERVIEW The B2K is a quality marking instrument specially designed to meet the needs of the professional style tournament player. The B2K is an electronic solenoid actuated computer controlled marking device. The major components of the B2K are machined from solid, aircraft-grade aluminum, and then hard anodized per military specifications. No castings are used in the construction of the B2K, thereby providing the end user with a high-quality, precision-engineered marking instrument.
PAGE 4
OPERATION Read the entire manual before you prepare your B2K for firing. Safety and safe gun handling are the most important aspects of paintball sports. Please practice each of the following steps with an unloaded gun before attempting to charge your gun with compressed air and paint pellets. Do not load compressed air and paint pellets into your B2K until you feel completely confident with your ability to handle your B2K safely.
PAGE 5
instructions. Before removing the tray, remove the grip frame side panel on the left side, exposing the CPU and switches. Note the blue wires looped down into the PCB cavity. This loop is to allow the necessary distance between the tray and upper body to change the battery or maintain the solenoid. This loop must be maintained when re-assembly is completed. To remove the tray, use a 7/64 allen wrench and remove the four 6-32X1" screws around the bottom of the Αtray≅.
PAGE 6
can be used successfully if used with anti-siphon systems and filters. Be aware that under the conditions of CO2 the results may not be as expected. REMEMBER: CO2, compressed air or nitrogen systems can be extremely dangerous if misused or improperly handled. Use only D.O.T. certified tanks. Before pressurizing your B2K, check to make sure that you have a barrel plug in place and there is no paint in the gun. The on-off switch should be OFF.
PAGE 7
Mode selection is accomplished using switches 1 thru 3. The following configurations will give you the desired modes. Modes Semi-Auto 2 shot Burst 3 shot Burst 6 shot Burst Auto-Response Turbo Mode Zip (ramp) Full Auto Switch numbers #1 #2 off off on off off on on on off off on off off on on on #3 off off off off on on on on Rate of Fire and timing is as follows: Dip switch #4 and #5 #4 #5 off off on off off on on on (registers Solenoid on times in milliseconds) = 06 ms (.006 seconds) = 08 ms (.
PAGE 8
Firing the B2K Keep your finger out of the trigger guard and away from the trigger; point the muzzle of your gun in a safe direction at all times during this process. Be sure your goggles are securely in place. Push the on-off switch into the off position. Always keep your B2K pointed in a safe direction! 1. 2. 3. 4. 5. 6. 7. 8. Place the empty loader onto the gun. Be sure that it is securely mounted in place. Apply the compressed gas, pressurizing the gun. Put the paintballs into the loader.
PAGE 9
Simple Maintenance Keep your B2K clean and lubricated to eliminate the friction that would prevent reliable operation. Clean and lube the gun before each use, and do not put it away dirty. USE NO OILS! Do not use petroleum-based lubricants in the lubrication of this gun. Teflon or silicon spray lubricants are the recommended types of lubrication for the bolt area of the main housing. Lithium grease is recommended for lubricating the regulator pistons, and the cylinder assembly.
PAGE 10
hammer, if the link pin IS NOT PROPERLY replaced, you may damage the hammer/cylinder assembly.
PAGE 11
STORAGE AND TRANSPORTATION - Your B2K must be clear of all paint and propellant when not being used. - Be sure the on-off switch is off and the LED is not lighted. - Put the barrel plug in place. - Make sure the gun is clean. - Store your B2K in a clean, cool, dry place. - Keep your B2K away from children. This air gun is not a toy! To be used by adults only! Your B2K must be clear of all paint and any source of propellant during transportation to and from the playing field. Keep your barrel plug in place.
PAGE 12
ADJUSTING THE TRIGGER PULL You will notice two screws in your trigger. These screws adjust the length of pull and actuation point of the trigger. The bottom screw adjusts your trigger stop point (length of pull). The top screw is the contact point for your micro switch. 1. Use blue loctite while adjusting the screws. Normal activity can cause the screws to back out of adjustment. DO NOT glob the loctite on, it can cause damage to the micro switch if you use too much. 2.
PAGE 13
registered. A pressure gauge has been installed into the regulator body to indicate the exact operating pressure of the marker. This gauge is extremely useful. At the factory we set the regulator gauge to 225-300 PSI with an input pressure of 400 PSI using Compressed air as the base propellant. Under normal circumstances these settings will produce paintball velocities at approximately 280-300 fps. The input pressure from your tank should be set at 350-500 PSI.
PAGE 14
1. The B2K has a leak down the barrel. Reason: gas is leaking through or around the valve pin seal or O>ring area. a. Can you hear the leak when the gas is removed? Yes? There is no leak. You hear the ocean. b. The valve seal is marred/scratched or worn out or dirt has gotten to it. Replace it. 2. The B2K has a leak around the high pressure regulator seam. Reason: the seal between the regulator body and the main body is bad. a. Tighten the regulator to the body. b. Check and/or replace the O’ring. 3.
PAGE 15
your trigger timing. c. If the ball retention ball does not move freely, the paintballs will crush against it or it may have stuck in the depressed position allowing double feeding. Check its tension regularly and keep this area as clean as possible. d. If the ball retention ball is too sloppy, the ball will not be held in the proper position. This may allow the next ball to enter the path of the bolt, subjecting it to impact cracking or shearing. Verify the tension. e.
PAGE 16
warranties. Battery Related Problems 1. LED functions but the marker does not fire. 2. Alternately missed shots. 3. Velocity drops while firing several shots. 4. Erratic Velocities. Jumps of 20 fps or more. 5. Unexplainable paint breakage. 6. Slight leak from the solenoid in the back of the grip. a. Change the battery. The LED only requires 1½ volts to function. The solenoid requires a minimum of 5 volts to operate. This means the marker may appear to be getting enough power when it is not.
PAGE 17
INDIAN CREEK DESIGN, INC. LIMITED WARRANTY Indian Creek Design, Inc., warrants the replacement of any original part due to defect in materials and/or workmanship of this air gun. This warranty will be in effect for twelve (12) months for parts and twelve (12) months for labor following the original date of purchase for the original purchaser.