IDE 44 Dishwasher Installation and use
Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - 97/17/EEC Labelling 1.Carefully dispose of the packing material. 2.
Close-up View (Interior) E G F H J K I L Upper Rack Bottom Sprayer Arm Top Sprayer Arm Salt Container Cap Rack Height Adjustor Washing Filter Lower Rack Detergent and Rinse Aid Dispenser Technical characteristics Width cm. 45 Depth cm. 60 Height cm.
Salt ...... Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Loading the Salt into the Softener Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: 1.
Detergent and Rinse Aid .... Rinse Aid This product makes dishes sparkle more as it improves their drying. The rinse aid container is situated on the inside of the appliance door; you should refill it when the low rinse aid indicator light "T" flashes. Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Wash Cycle Table.
Loading the Dishwasher Before placing the dishes in the racks, remove the largest scraps of food left over on your plates, you will thus avoid blocking the filter, which would reduce the efficacy of the wash. If the saucepans and frying pans are very dirty, allow them to soak before being washed. You will thus avoid having to wash them again. To make it easier to load your dishes, pull the racks out fully.
Turning on the Appliance First of all Insert the plug into the electricity socket to power the dishwasher. Turn on the water tap completely and press ONOFF button "A"; the display lights up and the wash cycle time selected on the knob will flash. You've left out a dish? You can interrupt a wash cycle by pressing the "ON-OFF" button, then place the forgotten dishes into the appliance, which will start up, after approximately 10 seconds, from where it was interrupted when you turn it back on.
Setting a delayed start How to set a delayed start When you have loaded the dishes, you can choose when to start your dishwasher before setting the wash cycle desired. • Press button "P" repeatedly to postpone the start of the wash cycle from 1 hour to 24h. • If you press the button again, the word "OFF" is displayed (no selection made). Once you have made your selection, make sure the appliance door is shut and start the wash cycle by pressing the START button.
Wash Cycle Table Dishwasher washing guarantees your dishes will be cleaned in a hygienic setting for safer, cleaner results. &\FOH &\FOH VHOHFWLRQ LQVWUXFWLRQV Very dirty dishes and pans (not to be used for delicate items) ,QWHQVLYH Normally dirty pans and dishes. Standard daily cycle. 7LPH
Energy Saving Tips - It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. - Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are.
Cleaning and Special Maintenance The filter assembly If you want consistent good results from your dishwasher, you need to clean the filter assembly; this way the food particles are removed from the wash water, allowing it to be recirculated during the cycle, filtered perfectly. For this reason, it is a good idea to remove the larger food particles trapped inside the cup “C” and semi-circular filter “A” after each wash.
Installation Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation. Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the dishwasher, making it level.
Electrical Connection Electrical Connection If your appliance is supplied with a 13 amp. fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instruction below. WARNING: THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN. Replacing the fuse: When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted.
Merloni Elettrodomestici P04/2004 - 195043341.00 - Xerox Business Services - DocuTech Viale Aristide Merloni 47 60044 Fabriano Italy Tel +39 0732 6611 Fax +39 0732 662501 www.merloni.
