ASSEMBLY INSTRUCTION
Caution Keep children and pets away from the electric height-adjustable desk during the operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a long time. Make sure desktop not touching the wall. Ensure no obstacles in the desk’s path and no object above and 20” under the desk. Working environment temperature 0-40℃, keep products away from corrosive gas, liquid and dusty objects.
Parts List A - Column A B - Column B E - Girder F - Sync Rod I - Bracket J - Cable clip x 6 C - Foot x 2 D - Side Bracket x 2 H - Hook x 2 K - M5 Allen Key L - M3 Allen Key M - Connecting board x 3 N - Control Box O - Power Supply P - Power Cord Q - M6x10 Screw x 12 R - ST4.8x13 screw x 32 S - ST2.
Assembly Step 1 Checklist M5 A - Column A A Q B B - Column B E - Girder E M5 Q - M6x10 Screw x 8 M3 Step 2 LOOSE F √ √ Checklist F - Sync Rod × × L - M3 Allen Key M3 TIGHTEN 3
Assembly Step 3 Checklist Q M5 D - Side Bracket x 2 D Q - M6x10 Screw x 4 M5 D Step 4 M5 Checklist C T C - Foot x 2 C T - M6x16 Screw x 8 M5 √ Step 5 × Checklist V ③ ③ Y - Table board ③ √ × V - Screw x 7 4
Assembly Step 6 Checklist ④ ④ Y - Table board ④ X X - Wooden pin x 2 W - Cam x 3 180° W Step 7 Checklist ⑥ ⑤ ⑤ ⑥ ⑥ Y - Table board ⑤x2/⑥x2 ⑤ Sealing side X - Wooden pin x 8 X W - Cam x 4 180° W 5
Assembly Step 8 Checklist X ① ① ② Y - Table board ①② ② X - Wooden pin x 5 R M M - Connecting board x 3 R - ST4.
Assembly Step 10 Checklist U U - M4x35 Screw x 11 Use the support block to keep it steady Avoid excessive tightening screws Step 11 Checklist R H - Hook x 2 H R - ST4.
Assembly Step 12 Checklist 90° I I - Bracket 90° 90° 60° 90° Step 13 Checklist R I - Bracket I R - ST4.
Assembly Step 14 Checklist N N - Control Box S S - ST2.
Instruction 1 · Manual Reset 2. ▲ 1. rES 27.6 3. 2 3 ▲ ▲ S It is necessary to be reset manually after the initial installation and power off. · Keep pressing down key till the desktop till display shows“E-1”and“rES” alternately and release the key. · Keep pressing down key, the desktop will move slowly down and retum back till the display shows“27.6”. · Release the key, the height-adjustable desk resetting finished. Note: The anti-Collision function is not enabled during all resets.
Instruction · Anti-Collision function E-2 1. Before use, please make sure removing obstacle in advance and human body is in the safe position. · Once the desktop encounters any obstacle in its path, the screen displays“E-2”。 · The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle. · Container and self-stop positions S 1. Do not enable this function only when you are really need in some situation.
Instruction · Amend the desktop height displayed ▲ 1. rES S 2. 3. ▲ ▲ 4. 1 2 · Keep pressing down key till the desktop till display shows“E-1”and“rES” alternately and release the key. · Keep pressing key“S”till the display show“A - - ”alternately. · Keep“Up”or“Dn”several times,till the display show“End”and height.
Code meaning and Trouble shooting 【Code meaning】 Code Information E-1/rES Manual resetting Operating Refer to the progress of manual reset Remove the load on desktop till it less than 800N(175LBS) for further operation ovr Overloading E-2 Anti-Collision function It can be used normally after removing the obstacle dut Operated continuously without suitable rest Make the desk rest around 15minutes for further operation 【Trouble shooting】 Code Operating E-3 Check the cables and ensure they are
