User's Manual

ManualsBrandsIn Tech Electronics ManualsElectronicsBluetooth Neckloop Pendant

Table Of Contents

292.00 mm

264 mm

6 10

User Manual

CS8140

Bluetooth Neckloop Pendant

Pendant pictures

Wearing the pendant

Wear Neckloop Pendant over your head and around your neck.

Charging the battery

Thank you for buying the new Pendant CS8140 with Bluetooth

wireless technology. Before first time use, it is important to

charge the Pendant until the red LED turns off.

Volume

Down(S3)

Volume

Up(S2)

On/Off(S1)

Microphone

Socket

Turning on the pendant

When the Pendant is powered down, press and hold S1 until

blue LED turns on indicates that the Pendant is powered up.

Blue LED will flash every 3 seconds.

Turning off the pendant

When the Pendant is powered up,press and hold S1 until red

LED turns on indicates that the Pendant is powered down.

Connection between Neckloop Pendant and hearing aid

The Pendant can communicate with your hearing aid when

your hearing aid is in T-coil mode or T-coil + MIC mode

(operation of your hearing aid, please refer to its user

manual).The Pendant will transfer mobile phone communic-

ation to your hearing aid wirelessly. We strongly recommend

you to switch your hearing aid to T-coil mode when you use

the Pendant.

Warning: Do not use Pendant when you use a pace maker

or any other devices that may be sensitive to magnetic/

inductive field.

Connecting to Bluetooth mobile phone

Pendant in pairing mode

 Before start pairing, make sure the Pendant is fully charged

and the charging cable is disconnected from it. When the

Pendant is powered off,press and hold S1 until red and blue

LEDs flashing alternately. It indicates that the Pendant is in

Pairing Mode.

 Following the operating instructions for your Bluetooth

mobile phone to start the pairing process. Typically, this

has to be done by going to a setup or connect menu and

then selecting the options to discover Bluetooth devices.

Bluetooth may take several seconds to establish a

connection.

 Your phone’s display should indicate that it has found the

Pendant “NECKLOOP” and asks if you want to pair it. You

should confirm it.For Bluetooth mobile phone compliant with

2.1, its easy-pairing feature enables successful pairing

without asking for a passkey. For Bluetooth mobile phone

compliant with 2.0 or downward versions, phone’s display

would prompt you for a passkey or PIN. Enter a sequence

of “0000”.

 The Pendant LED will flash blue every 3 seconds, indicating

successful pairing. Usually the phone will ask whether you

want to change the Pendant’s name. We recommend you to

keep the default name “NECKLOOP”.

 If pairing doesn’t occur as expected. Turn off both Pendant

and Phone and wait for 10 seconds. Turn on Pendant and

phone again and repeat all steps from beginning. Pairing

does authorize the devices like mobile phones and

Pendant with each other and only needs to be performed

once.

Establishing Bluetooth link

After successful pairing, the Pendant and the mobile phone,

you may need to establish a Bluetooth link between them

according to the operation manual of your mobile phone. To

establish the link, press S1 shortly. Use Nokia 6130i as an

example, the mobile phone will show “ Do you accept

NECKLOOP request for connection?”Select YES to establish

the link. You are ready to make and answer calls on the

Pendant. For other phones, please follow the operation

manual to establish the link.

Please note:

If the Pendant is turned off, turning on the Pendant again will

auto reconnect the last used device. If the Pendant is disconn-

ected but powered on, press S1 shortly to connect the link

again. If there is abnormal loss of link happened (e.g. out of

range), the Pendant will automatically try to reconnect the

mobile phone several times.

Answering incoming calls

When you wear the Pendant and there is an incoming call

presented, the Pendant will ring. Press S1 will answer the call.

Attention: Some phones put the Bluetooth connection into

standby mode if it has not been used for some time. When

there is phone call in, only the mobile phone rings and it will

take a few seconds to transfer the call to Pendant. You have

to wait until you hear the ring tone from Pendant. If you press

S1 to take the call before you hear the ring tone from Pendant,

the Pendant will try to establish Bluetooth connection. This

will cause connection conflict between mobile phone and

Pendant.

Ending calls

While a call is in session on the Pendant, pressing S1 will disc-

onnect the call. After the call is disconnected, the blue LED will

flash normally again.

Call waiting

The call waiting feature only supports when the SIM card of

your mobile phone is with this function.

When a call (Call 1) is in session on Pendant and there is

another call (Call 2) coming. “Double” tone will be heard. Both

LEDs turn on simultaneously in every 2 seconds.

Muting the microphone

To mute the microphone during an active call, press both S2 &

S3 simultaneously for a second and the microphone will be

muted. A periodic beep tone will be heard when the mute

function is active.

To end the mute function:when the microphone is muted,press

both S2 & S3 simultaneously. Mute function is ended and the

periodic beep tone will stop.

Transferring calls (For Nokia N5700 or equivalent models)

When a call is in session, call can be transferred from the

Bluetooth phone to the Pendant and from the Pendant to the

Bluetooth phone.

 To transfer a call from Bluetooth mobile phone to the Pendant:

press S1 once, the call will be transferred to Pendant.

 To transfer a call from Pendant to Bluetooth mobile phone,

please follow the operating instructions of your mobile phone.

To make a new call using voice dial

Make sure the voice dialing function is set up in the mobile

phone and it is within the operating range of the Pendant.

Press S1 on the Pendant shortly.There is a beep tone on the

Pendant. Then use your recorded voice commands(e.g. By

saying the name of the person). The call will be connected

in a few seconds.

Redialing last dialed number (Mobile phones with

Handsfree profiles only )

To redial the last number, press and hold S3 until 4 tones

are heard. It indicates the redial is active.

Reject a call

To reject a call at the time when the Pendant rings, press

and hold S1 until you hear a tone.

Adjusting speaker volume

When a call is session,pressing and releasing S2 will increase

the speaker volume and pressing and releasing S3 will

decrease the speaker volume on the Pendant. There is a key

tone to indicate volume increase or decrease. However, a

warning tone will be heard when the volume level reaches its

maximum or minimum.

Noted:Not all functions may be available on all mobile phones

Low-battery indication

The Pendant LED will flash red instead of blue when the

battery level is low. There will also a short beep periodically.

After this indication you still have up to 15 minutes talk time.

When the battery level is too low, the Pendant will power off.

It can not power on again unless the charger is connected or

the battery is sufficiently charged.

Battery recharging

To recharge the battery, connect the charger cable to the

Pendant. During recharging, the LED shows a steady red

light. When the battery is fully charged, the red light will be

off.

The achievable talk time and standby time for the Pendant can

vary with different Bluetooth mobile phones due to different

implementation of power down modes.

Keep the Pendant away from the fire to avoid damage.

Warning:

For adaptor, the socket-outlet shall be installed near the

equipment and shall be easily accessible.

Pendant pictures.................................................................. 1

Wearing the pendant.............................................................1

Charging the battery..............................................................1

Turning on the pendant......................................................... 2

Turning off the pendant......................................................... 2

Connection between Neckloop Pendant and hearing aid.......... 2

Connecting to Bluetooth mobile phone................................... 3

Establishing Bluetooth link ....................................................4

Answering incoming calls...................................................... 5

Ending calls .........................................................................6

Call waiting......................................................................... . 6

Muting the microphone.......................................................... 7

Transferring calls (For Nokia N5700 or equivalent models).......7

To make a new call using voice dial.........................................8

Redialing last dialed number (Mobile phones with

Handsfree profiles only )........................................................8

Reject a call..........................................................................8

Adjusting speaker volume......................................................9

Low-battery indication...........................................................9

Battery recharging .............................................................10

LED status.......................................................................... 11

Trouble shooting guide........................................................ 12

Maintenance and care......................................................... 13

FCC Interference Statement .............................................. . 14

Declaration of Conformity...................................................1 7

 To answer Call 2, press S2 for about 2 seconds. It will switch

between Call 1 & Call 2.

 To reject Cal 2, press S1 shortly.

Both red/blue LEDs will turn on simultaneously

every second

when Call 1 or Call 2 is in session.

When Call 2 is in session and Call 1 is on held in other line,

press S1 shortly will end Call 1.If you want to end Call 2, press

S3 for about 2 seconds.

Summary of content (2 pages)

PAGE 1
264 mm User Manual Bluetooth® Neckloop Pendant Pendant pictures.................................................................. 1 Wearing the pendant.............................................................1 Charging the battery..............................................................1 Turning on the pendant......................................................... 2 Turning off the pendant.........................................................
PAGE 2
Led status LED Status 1x1 Sec. Blue Talking 1x2 Sec. Blue Paired and connecting to BT device 1x3 Sec. Blue Ready can be accessed by paired devices Blinking red Battery low (Max 15 Minutes left) Red LED on Under charging Red LED off Fully charged Red/Blue Blinking Pairing-mode Red & Blue on simultaneously Call waiting mode Remark: When the battery level is low, the LED will not turn on until the Pendant is charged up, which may takes several minutes.