User Manual

ManualsBrandsIn Tech Electronics ManualsAudio EquipmentBluetooth Headset

PART NO

MCB-8131010-0A

.: MODEL:

8131

DRAWN:

Lucy

DATE:

September07,2007

PAPER SIZE:

UNIT:

SCALE:

11:

:DESCRIPTION

#USER MANUAL

In Tech Electronics Ltd-.

(1) A/C charging (2) Car charging

Low-battery indication

Battery recharging

The BT 29R LED will flash red instead of blue when the battery is low. There will

also a short beep periodically. After this indication you still have up to 15 minutes

talk time. When the battery level is too low, the Headset will automatically power

off. It cannot be powered on again unless the charger is connected or the battery is

sufficiently charged.

To recharge the battery, put the headset on phone holder. During recharging, the

LED shows a steady red light.

When the battery is fully charged, the indicators of red light will be off .

The achievable talk time and standby time for the BT 29R can vary with different

Bluetooth mobile phones due to different implementation of power down modes.

Keep the headset away from fire to avoid damage.

Redialing last dialed number (Mobile phones with Handsfree profiles only )

Reject a call (Mobile phones with Handsfree profiles only )

Adjusting Speaker Volume:

To wear the headset

To redial the last number, press and hold S3 until 4 tones are heard. It indicates the

redial is active.

To reject a call at the time the BT 29R rings, press and hold S1 until you hear 2

tones.

When a call is ongoing, pressing and releasing S2 will increase the speaker

volume and pressing and releasing S3 will decrease the speaker volume on the

Headset. There is a key tone to indicate volume increase or decrease. However, a

warning tone will be heard when the volume level reaches its maximum or

minimum.

Make sure the microphone is pointing towards your mouth.

Bluetooth

Headset

Headset pictures.....................................................................................1

Charging the battery................................................................................1

Turning on the Headset............................................................................1

Turning off the Headset............................................................................1

Headset in Pairing Mode..........................................................................2

Establishing Bluetooth Link......................................................................3

Answering incoming calls.........................................................................3

Transferring calls....................................................................................4

Muting the microphone.............................................................................4

Ending calls............................................................................................4

To make a new call using voice dial...........................................................4

Redialing last dialed number....................................................................5

Reject a call............................................................................................5

Adjusting speaker volume........................................................................5

To wear the headset.................................................................................5

Low-battery indication.............................................................................6

Battery recharging...................................................................................6

LED Status..............................................................................................7

Voice Over Internet Protocol (VoIP) Application.........................................8

FCC Interference statement ....................................................................9

Declaration of Conformity.....................................................................11

Charging the battery

Turning on the Headset

Turning off the Headset

Thank you for buying the new BT 29R Headset with Bluetooth wireless technology.

Before first time use, it is important to charge the battery for 8 hours.

While the Headset is powered down, press and hold S1 until blue LED turns on. A

low tone followed by a high tone will indicate that the BT 29R is powered up.

Afterward, blue LED will flash every 3 seconds.

While the Headset is powered up, press and hold S1 until red LED turns on. A

high tone followed by a low tone will indicate that the BT 29R is powered down.

Headset in Pairing Mode

Ma sure the BT 29R is fully charged and the charging cable is disconnected

from it before pairing starts. While the BT 29R is powered off, press and hold

S1 until red and blue LEDs flashing alternately. It indicates that the Headset is

in Pairing Mode.

Follow the operating instructions for your Bluetooth mobile phone to start the

pairing process. Typically, this has to be done by going to a setup or connect

menu and then selecting the options to discover Bluetooth devices. Bluetooth

may take several seconds to establish a connection.

Your phone's display should indicate that it has found the “BT 29R” headset

and asks if you want to pair it. You should confirm this. The phone's display

would prompt you for a passkey or PIN. Enter a sequence of “0000”.

The headset LED will flash blue every 3 seconds, indicating successful pairing.

Usually the phone will also ask whether you want to change the headset's name.

We recommend to keep the default name BT 29R instead of changing it.

If pairing does not occur as expected: Turn off both the headset and the phone

and wait for 10 seconds. Turn on the headset and phone again and repeat all

steps from beginning. Pairing does authorize the devices like mobile phones and

headsets with each other and only needs to be performed once.

Transferring Calls (For Nokia 3650 or equivalent models)

Muting the microphone

Ending Calls

To make a new call using voice dial

When you are in session, calls can be transferred from the Bluetooth phone to the

HS and from the HS to the Bluetooth phone.

To transfer a call from the Bluetooth phone to the HS: press S1 once, the call will

be transferred to the HS.

To transfer a call from HS to the Bluetooth phone, please follow the operating

instructions of your phone.

To mute the microphone during an active call press both S2 and S3 buttons

simultaneously for about a second and the microphone will be muted. A periodic

beep tone will be heard when the mute function is active.

To end the mute function: When the microphone is muted, press both S2 and

S3 buttons simultaneously. Mute function is ended and the periodic beep tone will

stop.

While a call is in session on the Headset pressing S1 will disconnect the call.

After the call is disconnected, the blue LED will flash normally again.

Make sure the voice dialing function is set up in the mobile phone and it is within

the range of the Headset. Press S1 on the BT 29R shortly. There is a beep tone

on the headset.Then use your recorded voice commands ( eg. By saying the

name of the person). The call will be connected in a few seconds.

Microphone

Speaker

On Off S1/()

Volume Up (S2)

Volume Down S3()

LED

DC Socket

Environmental

friendly

User Manual

BT 29R

Establishing Bluetooth Link

Please note:

After successfully pairing the BT 29R and the mobile phone, you may need to

establish a Bluetooth link between them according to the operation manual of your

mobile phone. To establish the link, press S1 shortly. Use Nokia 6130i as an example,

the mobile phone will show “Do you accept BT 29R request for connection?” Select

YES to establish the link. You are ready to make and answer calls on the Headset. For

other phones, please follow the operation manual to establish the link. You are ready to

make and answer calls on the Headset.

If the headset is powered down, turning on the headset will auto reconnect the last

used device. If the headset is disconnected but powered on, press S1 shortly to

connect the link again. If there is abnormal loss of link happened (e.g. out of range),

the headset will automatically try to reconnect the mobile phone several times.

If the mobile phone cannot locate the network signal (e.g. out of reach) , alert tone will

be heard every 5 seconds in the headset.

Not every mobile phone supports no network signal alert feature.

If there is no Bluetooth connection for more than 1 hour, the headset will switch off

automatically.

When you wear the headset, an incoming call is present, the BT 29R headset will ring.

Pressing S1 will answer the call.

Some phones put the Bluetooth connection into Standby Mode if it has not

been used for some time. When there is phone call in, only the mobile phone rings

and it will take a few seconds to transfer the call to headset. You have to wait until you

hear the ring tone in headset. If you press S1 to take the call before you hear the ring

tone in headset, the headset will try to establish Bluetooth connection. This will cause

connection conflicts between mobile phone and headset.

Answering Incoming Calls

Attention:

176.00 mm

Note

:Material 80g Woodfree Pater

Note

:Material 80g Woodfree Pater

296.00 mm

Summary of content (2 pages)

PAGE 1
A E D C B 8 8 176.00 mm BT 29R Establishing Bluetooth Link After successfully pairing the BT 29R and the mobile phone, you may need to establish a Bluetooth link between them according to the operation manual of your mobile phone. To establish the link, press S1 shortly. Use Nokia 6130i as an example, the mobile phone will show “Do you accept BT 29R request for connection?” Select YES to establish the link. You are ready to make and answer calls on the Headset.
PAGE 2
A E D C B 8 8 176.00 mm ● 7 Led Status LED Status 1 x 3 sec. Blue Ready can be accessed by paired devices 1 x 1 sec. Blue Talking Blinking red Battery low (max. 15 Minutes left) Red LED on Under charging Red LED off Fully charged Red/Blue Blinking Pairing-Mode 7 BT 29R Reminding: -For safety reason, please don't leave the headset in car alone when charging. -When the battery is low, the LED will not turn on until the headset is charged up, which may take several minutes.