User Manual

ManualsBrandsIn Tech Electronics ManualsAudio EquipmentBluetooth Headset

Table Of Contents

200.00 mm

270.00 mm

Headset pictures..................................................................................................1

Charging the battery.............................................................................................1

Turning on the Headset........................................................................................1

Turning off the Headset........................................................................................1

Headset in Pairing Mode.......................................................................................2

Establishing Bluetooth Link...................................................................................3

Answering incoming calls.....................................................................................3

Transferring calls.................................................................................................4

Muting the microphone.........................................................................................4

Ending calls.........................................................................................................4

To make a new call using voice dial........................................................................4

Redialing last dialed number................................................................................5

Reject a call.........................................................................................................5

Adjusting speaker volume.....................................................................................5

To wear the headset.............................................................................................5

Low-battery indication..........................................................................................6

Battery recharging................................................................................................6

LED Status...........................................................................................................7

Voice Over Internet Protocol (VoIP) Application......................................................8

FCC Interferences tatement ...................................................................................9

Declaration of Conformity...................................................................................11

● Charging the battery

Thank you for buying the new BT 30M Headset with Bluetooth wireless technology. Before

first time use, it is important to charge the battery for 8 hours.

● Turning on the Headset

While the Headset is powered down, press and hold S1 until blue LED turns on. A low tone

followed by a high tone will indicate that the BT 30M is powered up. Afterward, blue LED

will flash every 3 seconds.

● Turning off the Headset

While the Headset is powered up, press and hold S1 until red LED turns on. A high tone

followed by a low tone will indicate that the BT 30M is powered down.

Headset in Pairing Mode

 Make sure the BT 30M is fully charged and the charging cable is disconnected from it before

pairing starts. While the BT 30M is powered off, press and hold S1 until red and blue LEDs

flashing alternately. It indicates that the Headset is in Pairing Mode.

 Follow the operating instructions for your Bluetooth mobile phone to start the pairing process.

Typically, this has to be done by going to a setup or connect menu and then selecting the

options to discover Bluetooth devices. Bluetooth may take several seconds to establish a

connection.

 Your phone's display should indicate that it has found the “BT 30M” headset and asks if you

want to pair it. You should confirm this. The phone's display would prompt you for a passkey

or PIN. Enter a sequence of “0000”.

 The headset LED will flash blue every 3 seconds, indicating successful pairing. Usually the

phone will also ask whether you want to change the headset's name. We recommend to keep

the default name BT 30M instead of charging it. You can pair as many headsets and devices

as you wish in your mobile phone.

 If pairing does not occur as expected:Turn off both the headset and the phone and wait for 10

seconds. Turn on the headset and phone again and repeat all steps from beginning. Pairing

does authorize the devices like mobile phones and headsets with each other and only needs

to be performed once.

Establishing Bluetooth Link

After successfully pairing the BT 30M and the mobile phone, you may need to establish a

Bluetooth link between them according to the operation manual of your mobile phone. To

establish the link, press S1 shortly.Use Nokia 6130i as an example, the mobile phone will show

“Do you accept BT 30M request for connection?” Select YES to establish the link.You are ready

to make and answer calls on the Headset.For other phones,please follow the operation manual

to establish the link. You are ready to make and answer calls on the Headset.

Please note:

If the headset is powered down,turning on the headset will auto reconnect the last used device.

If the headset is disconnected but powered on, press S1 shortly to connect the link again. If an

abnormal disconnect (link loss) happens (e.g. out of range), the headset will automatically retry

to reconnect the AG (e.g. mobile phone) several times. Depend on the mobile phones, if no

mobile network signal found (e.g. out of reach) in the mobile phone, alert tones will be heard

every 5 seconds in the headset.

Answering Incoming Calls

When you wear the headset, an incoming call is present,the BT 30M headset will ring. Pressing

S1 will answer the call.

Attention: Some phones put the Bluetooth connection into Standby Mode if it has not been

used for some time. If a call comes in only the mobile phone rings and it will take a few seconds

before the call is transferred to the Headset as well (2-3 ring tones). You have to wait taking the

call until you hear the ring tone in the Headset. If you press S1 too early before the call is

transferred to the Headset, the Headset will try to establish a Bluetooth connection and cause

conflicts in the mobile phone.

Transferring Calls (For Nokia 3650 or equivalent models)

When you are in session, calls can be transferred from the Bluetooth phone to the HS and from

the HS to the Bluetooth phone.

To transfer a call from the Bluetooth phone to the HS: press S1 once, the call will be

transferred to the HS.

To transfer a call from HS to the Bluetooth phone, please follow the operating instructions of

your phone.

Muting the microphone

To mute the microphone during an active call press both S2 and S3 buttons simultaneously for

about a second and the microphone will be muted. A periodic beep tone will be heard while the

mute function is active.

To end the mute function: When the microphone is muted, press both S2 and S3 buttons

simultaneously. Mute function is ended and the periodic beep tone will stop.

Ending Calls

While a call is in session on the Headset pressing S1 will disconnect the call. After the call is

disconnected, the blue LED will flash normally again.

To make a new call using voice dial

Make sure the voice dialing function is set up in the mobile phone and it is within the range of

the Headset. Press S1 on the BT 30M shortly. There is a beep tone on the headset.Then use

your recorded voice commands ( eg. By saying the name of the person). The call will be

connected in a few seconds.

Microphone

Speaker

On/Off(S1)

Volume Up (S2)

Volume Down(S3)

LED

DC Socket

(1) A/C charging (2) Car charging

Low-battery indication

The BT 30M LED will flash red instead of blue when the battery is low. There will also a

short beep periodically. After this indication you still have up to 15 minutes talk time. When

the battery level is too low, the Headset will automatically power off. It cannot be powered

on again unless the charger is connected or the battery is sufficiently charged.

Battery recharging

To recharge the battery, put the headset on phone holder. During recharging, the LED

shows a steady red light.

When the battery is fully charged, the indicators of red light will be off .

The achievable talk time and standby time for the BT30M can vary with different Bluetooth

mobile phones due to different implementation of power down modes.

Keep the headset away from fire to avoid damage.

Redialing last dialed number (Mobile phones with Handsfree profiles only )

To redial the last number, press and hold S3 until 4 tones are heard. It indicates the redial is

active.

Reject a call (Mobile phones with Handsfree profiles only )

To reject a call at the time the BT 30M rings, press and hold S1 until you hear 2 tones.

Adjusting Speaker Volume:

While a call is ongoing, pressing and releasing S2 will increase the speaker volume and

pressing and releasing S3 will decrease the speaker volume on the Headset.There is a key

tone to indicate volume increase or decrease. However, a warning tone will be heard when

the volume level reaches its maximum or minimum.

To wear the headset

Make sure the microphone is pointing towards your mouth.

User Manual

BT 30M

Bluetooth Headset

Environmental

friendly

Bluetooth Qualified Design ID: B0xxxx

Summary of content (2 pages)

PAGE 1
200.00 mm Bluetooth Qualified Design ID: B0xxxx BT 30M User Manual Establishing Bluetooth Link After successfully pairing the BT 30M and the mobile phone, you may need to establish a Bluetooth link between them according to the operation manual of your mobile phone. To establish the link, press S1 shortly.Use Nokia 6130i as an example, the mobile phone will show “Do you accept BT 30M request for connection?” Select YES to establish the link.You are ready to make and answer calls on the Headset.
PAGE 2
● Led Status LED Status 1 x 3 sec. Blue Ready can be accessed by paired devices 1 x 1 sec. Blue Talking Blinking red Battery low (max. 15 Minutes left) Red LED on Under charging Red LED off Fully charged Red/Blue Blinking Pairing-Mode BT 30M / BT 30i Reminding: - For safety reason, please don't leave the headset in car alone when charging. - When the battery is empty, the LED will not turn on until the headset is charged up, which may take several minutes.