User Manual

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
us ed in ac corda nce w ith t he in stru c tion s , ma y ca use h armf u l
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
6
! Bend the ear hook to
Fit your ear
! Low-battery indication
The HS LED will flash red instead of blue when the battery is low.
There will also be a beep periodically. When the battery level is too low, the HS
will automatically power off. It cannot be powered on again unless the charger is
connected.
! Charging and recharging the battery
To recharge the battery, connect the charger cable to the HS. During recharging,
the LED shows a steady red light. When the battery is fully charged, the indicators
of red will be off.
1. Put on the headset with the ear hook behind your ear.
2. Bend the ear hook gently to fit your ear.
Notice: Make sure the microphone is pointing towards your mouth.
DISCLAIMER: Talk time and stand-by time of the BT 27MM Bluetooth Headset will vary depending on
mobile phone model being used
! Putting way
C Ada
pt r
A
o
AC M
a
i s
n
! Charging Connection
(1) A/C charging
NOTE:
BQB, CE and FCC approved.
UB 22S USB Bl ue tooth Don gle and BT 27MM Bluetooth Headset
Voice Over Internet Protocol (VoIP) Application
Plug the UB 22S USB Bluetooth Dongle (purchased separately) into the USB socket of
a PC.
Install IVT BlueSoleil Bluetooth application from the CD-ROM provided in the UB 22S
package. Note that the CD-ROM is not available in the BT 27MM package.
Download from the corresponding websites and install MSN messenger, Netmeeting,
Yahoo messenger, or ICQ application software in the PC.
Pairing: Put the BT 27MM Bluetooth Headset into “pairing” mode by following the
steps in the BT 27MM User Manual, start the BlueSoleil application and pair the UB
22S Dongle with the BT 27MM Headset. The Headset passkey is “0000”.
Connecting and Disconnecting: The UB 22S Dongle will ring the BT 27MM Headset.
Please press the S1 key on the headset to confirm the connection request. To
disconnect the Bluetooth link, press the S1 key again. You can now pair and
reconnect your BT 27MM Headset to your Bluetooth mobile phone, if you desire.
Testing the Bluetooth Link: After the UB 22S Dongle is paired with the BT 27MM
Headset, the PC audio will be automatically routed to the “Bluetooth Audio”driver.
Play some music on the PC by Windows Media Player or other music applications; you
should be able to hear the music on the Headset. If you can’t hear it, then go
the“control Panel”-> “Sound and Audio Device Properties”-> “Audio”-> “Sound
playback” select the “Bluetooth Audio”to activate the link.
Now you can start using the VoIP application and talk to your friend through your
headset wirelessly and freely.
Connecting BT 27MM Bluetooth Headset back to your Bluetooth mobile phone.
Please follow the steps from ‘Putting Headset in Pairing Mode’ to ‘Establishing
Bluetooth Link’ on page 2.
1.
2.
3.
4.
5.
6.
7.
8.
1
2
3
4
5
6
7
8
A
B
C
D
E
A
B
C
E
1
2
3
4
5
6
7
8
D
PART NO.:
MCB-8122010-0A
MODEL:
CS8122
DRAWN:
Limingzan
DATE:
Feb./08/2007
PAPER SIZE:
A3
UNIT:
MM
SCALE:
1:1
DESCRIPTION:
#User Manual,No Logo(Rom)
In-Tech Electr onics Ltd.
Note
Material: 80g Woodfree Pater
4
5