User Manual

ManualsBrandsIn Tech Electronics ManualsAudio EquipmentBluetooth Headset

Bluetooth Headset

User Manual

! Charging the battery

Thank you for buying new BT 27MM Bluetooth Headset. Before first time use, it is

important to charge the battery for 12 hours.

! Turning on the Headset

While the Headset (HS) is powered down, press and hold S1unitl Blue LED turn on.

A low tone followed by a high tone will indicate that the HS is powered up.

! Turning off the Headset

While the HS is powered up, press and hold S1 until red LED on. A high tone

followed by a low tone will indicate that the HS is powered down.

Headset pictures..............................................................................................................1

Charging the battery.........................................................................................................1

Turning on the Headset....................................................................................................1

Turning off the Headset....................................................................................................1

Putting Headset in Pairing Mode......................................................................................2

Establishing Bluetooth Link..............................................................................................2

Answering incoming calls.................................................................................................2

Transferring calls..............................................................................................................2

Muting the microphone.....................................................................................................2

Ending calls.....................................................................................................................3

To make a new call using voice dialing.............................................................................3

Redialing last dialed number............................................................................................3

Rejecting incoming call.....................................................................................................3

Adjusting speaker volume................................................................................................3

Ear Hook orientation........................................................................................................3

Bend the ear hook to fit your ear.......................................................................................4

Putting way.......................................................................................................................4

Low-battery indication......................................................................................................4

Charging and recharging the battery.................................................................................4

Charging Connection Diagrams....................................................................................5

Voice Over Internet Protocol (VoIP) Application..............................................................5

Microphone

Speaker

Ear hook

Lock

On/Off(S1)

Volume Up (S2)

Volume Down(S3)

LED

DC Socket

! Putting Headset in Pairing Mode

Make sure the HS is fully charged and charging cable disconnected from it before

pairing starts. While the HS is powered off, press and hold S1 until red and blue

LEDs flash alternately .It indicates the HS is Pairing Mode.

Follow the operating instructions for your Bluetooth mobile phone to start the

pairing process. Typically, this has to be done by going to a setup or connect

menu and then selecting the options to discover Bluetooth devices. Bluetooth

may take several seconds to establish a connection.

Your phone’s display should indicate that it has found the “BT 27MM” headset and

asks if you want to pair it. You should confirm this. The phone’s display would

prompt you for a passkey or PIN. Enter a sequence of “0000”.

The headset LED will flash Blue every 3 seconds, indicating successful pairing.

Usually the phone will also ask whether you want to change the headset’s name.

We recommend you should approve the BT 27MM name and not change it. You

can pair as many headsets and devices as you wish in your mobile phone.

If pairing does not occur as expected. Turn the headset and phone off and wait for

10 seconds. Turn the headset and phone on again and repeat all steps from

beginning.

! Establishing Bluetooth Link

After pairing, the mobile phone will show “connect”, then please select “YES” to

establish the link. Now you are ready to make and answer calls on the HS. For

other phones, please follow the operation manual to establish the link.

! Answering Incoming Calls

When an incoming call is present, the HS will ring . Pressing S1 will answer the

call. The blue LED will continue to flash fast while the call is in session. (Once

every second)

! Transferring Calls (For Nokia 3650 or equivalent models)

When you are in session, calls can be transferred from the Bluetooth phone to the

HS and from the HS to the Bluetooth phone.

To transfer a call from the Bluetooth phone to the HS: press S1 once, the call will

be transferred to the HS.

To transfer a call from HS to the Bluetooth phone, please follow the operating

instructions of your phone.

Muting the microphone

To mute the microphone during an active call

Pressing both S2 and S3 buttons simultaneously for about a second, the

microphone will be muted. A periodic beep tone will be heard while the mute

function is active.

To end the mute function

When the microphone is muted, press on both S2 and S3 buttons simultaneously

will end the mute function and the periodic beep tone will stop.

! Ending Calls

While a call is in session on the Headset, pressing S1 will disconnect the call.

After the call is disconnected, the blue LED will flash normally.

! To make a new call using voice dialing

W hen using a Bluetooth mobile phone:

1.Make sure the voice dialing function is probably set up in the Mobile phone and

it is within the range of the HS. Press S1 on the HS shortly.

2.After the tones on the mobile phone, make a voice dial as you normally would

by saying the name of the person on the HS. The call will be connected in a few

seconds.

When using a mobile phone without Bluetooth built-in and requiring a Bluetooth

dongle:

1.Make sure the voice dialing function is probably set up in the mobile phone and

it is within the range of the HS. Press S1 on the HS shortly.

2.After the tones on the mobile phone, make a voice dial as you normally would

and the call will be connected in a few seconds.

! Redialing last dialed number (Support handsfree profile mobile only. For Nokia

3650, Siemens S55, or equivalent models)

To redial the last dialed number, press and hold S3 for 1 seconds. 4 tones will

indicate an attempt to redial.

Rejecting incoming call (Support handsfree profile mobile only. For Nokia

3650, Siemens S55, or equivalent models)

When there is an incoming call and you want to reject it, press the buttons S1 and

hold it until you hear 2 tones, then release it.

! Adjusting Speaker Volume

While a call is in session, pressing and releasing S2 will increase the speaker

volume; pressing and releasing S3 will decrease the speaker volume on the HS.

There is a key tone to indicate volume increase or decrease.

! Ear Hook orientation

If you want to change the orientation of ear hook, please follow the following steps.

1) Detach the ear hook from the headset

2) Select the orientation you want (left or right), and attach the ear hook and lock it

200.00 mm

270.00 mm

PART NO.:

MCB-8122010-0A

MODEL:

CS8122

DRAWN:

Limingzan

DATE:

Feb./08/2007

PAPER SIZE:

UNIT:

SCALE:

1:1

DESCRIPTION:

#User Manual,No Logo(Rom)

In-Tech Electr onics Ltd.

Note

Material: 80g Woodfree Pater

BT 27MM

CS8122 / Abe

Summary of content (4 pages)

PAGE 1
A E D C B CS8122 / Abe 8 8 200.00 mm BT 27MM 7 ! Putting Headset in Pairing Mode Make sure the HS is fully charged and charging cable disconnected from it before pairing starts. While the HS is powered off, press and hold S1 until red and blue LEDs flash alternately .It indicates the HS is Pairing Mode. 7 Follow the operating instructions for your Bluetooth mobile phone to start the pairing process.
PAGE 2
A E D C B 8 8 Federal Communication Commission Interference Statement ! Bend the ear hook to Fit your ear 7 7 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 3
A E D C B CS8123 / Abe 8 8 200.00 mm BT 27iM 7 ! Putting Headset in Pairing Mode Make sure the HS is fully charged and charging cable disconnected from it before pairing starts. While the HS is powered off, press and hold S1 until red and Blue LEDs flash alternately . It indicates the HS is Pairing Mode. 7 Follow the operating instructions for your Bluetooth mobile phone to start the pairing process.
PAGE 4
A E D C B 8 8 ! Bend the ear hook to fit your ear 7 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.