User Manual
1
2
3
4
5
6
7
8
A
B
C
D
E
A
B
C
E
1
2
3
4
5
6
7
8
D
A3
PART NO
MCB-8059050-0B
.: MODEL
CS 120
:
8
DRAWN:
Lucy
DATE:
02/02/2007
PAPER SIZE:
A3
UNIT:
MM
SCALE:
11:
:DESCRIPTION
#USE MANUAL
In Tech Electronics Ltd-.
! Ear Hook orientation
If you want to change the orientation of ear hook, please follow the following steps.
1) Detach the ear hook from the Headset
2) Select the orientation you want (left or right), and attach the ear hook and lock it
2
Bluetooth
®
Headset
User Manual
User Manual
E
1
3
User Manual
Headset pictures..............................................................................................................1
Charging the battery.........................................................................................................1
Turning on the Headset....................................................................................................1
Turning off the Headset....................................................................................................1
Putting Headset in Pairing Mode......................................................................................2
Establishing Link..............................................................................................2
Answering incoming calls.................................................................................................2
Transferring calls..............................................................................................................2
Muting the microphone.....................................................................................................2
Ending calls.....................................................................................................................3
To make a new call using voice dialing.............................................................................3
Redialing last dialed number............................................................................................3
Rejecting incoming call.....................................................................................................3
Adjusting speaker volume................................................................................................3
Ear Hook orientation........................................................................................................3
Bend the ear hook to fit your ear.......................................................................................4
Putting way.......................................................................................................................4
Low-battery indication......................................................................................................4
Charging and recharging the battery.................................................................................4
Charging Connection Diagrams......................................................................................5
Voice Over Internet Protocol (VOIP) Application...............................................................5
FCC Interference Statement.............................................................................................6
Bluetooth
On Off S1/()
Volume Up (S2)
Volume Down S3()
LED
DC Socket
Microphone
Speaker
Ear hook
Lock
User Manual
BT 25EM
!
!
Charging the battery
Turning on the Headset
Turning off the Headset
Thank you for buying new BT 25EM Headset. Before first time use, it is
important to charge the battery for 6 hours.
While the Headset (HS) is powered down, press and hold S1 until Blue LED turn on.
A low tone followed by a high tone will indicate that the HS is powered up.
While the HS is powered up, press and hold S1 until red LED on. A high tone
followed by a low tone will indicate that the HS is powered down
Bluetooth
!
!
!
!
!
Putting Headset in Pairing Mode
Establishing Bluetooth Link
Answering Incoming Calls
Transferring Calls
Muting the microphone
Make sure the HS is fully charged and charging cable disconnected from it before
pairing starts. While the HS is powered off, press and hold S1 until red and blue
LEDs flash alternately It indicates the HS is Pairing Mode.
Follow the operating instructions for your mobile phone to start the
pairing process. Typically, this has to be done by going to a setup or connect
menu and then selecting the options to discover devices.
may take several seconds to establish a connection.
Your phone’s display should indicate that it has found the “BT 25EM” headset and
asks if you want to pair it. You should confirm this. The phone’s display would
prompt you for a passkey or PIN. Enter a sequence of “0000”.
The headset LED will flash Blue every 3 seconds, indicating successful pairing.
Usually the phone will also ask whether you want to change the headset s name.
We recommend you should approve the BT 25EM name and not change it. You
can pair as many headsets and devices as you wish in your mobile phone.
If pairing does not occur as expected. Turn the headset and phone off and wait for
10 seconds. Turn the headset and phone on again and repeat all steps from
beginning.
After pairing, the mobile phone will show “connect”, then please select “YES” to
establish the link. Now you are ready to make and answer calls on the HS. For
other phones, please follow the operation manual to establish the link.
When an incoming call is present, the HS will ring. Pressing S1 will answer the
call. The blue LED will continue to flash fast while the call is in session. (Once
every second)
(For Nokia 3650 or equivalent models)
When you are in session, calls can be transferred from the phone to the
HS and from the HS to the phone.
To transfer a call from the phone to the HS: press S1 once, the call will
be transferred to the HS.
To transfer a call from HS to the phone, please follow the operating
instructions of your phone.
Pressing both S2 and S3 buttons simultaneously for about a second, the
microphone will be muted. A periodic beep tone will be heard while the mute
function is active.
When the microphone is muted, press on both S2 and S3 buttons simultaneously
will end the mute function and the periodic beep tone will stop.
.
'
Bluetooth
Bluetooth Bluetooth
Bluetooth
Bluetooth
Bluetooth
Bluetooth
To mute the microphone during an active call
To end the mute function
!
!
!
Ending Calls
To make a new call using voice dialing
Redialing last dialed number
Rejecting incoming call
Adjusting Speaker Volume
While a call is in session on the Headset, pressing S1 will disconnect the call.
After the call is disconnected, the blue LED will flash normally.
1.Make sure the voice dialing function is probably set up in the Mobile phone and
it is within the range of the HS. Press S1 on the HS shortly.
2.After the tones on the mobile phone, make a voice dial as you normally would
by saying the name of the person on the HS. The call will be connected in a few
seconds.
1.Make sure the voice dialing function is probably set up in the mobile phone and
it is within the range of the HS. Press S1 on the HS shortly.
2.After the tones on the mobile phone, make a voice dial as you normally would
and the call will be connected in a few seconds.
(Support handsfree profile mobile only. For Nokia
3650, Siemens S55,
or
equivalent models)
To redial the last dialed number, press and hold S3 for 1 seconds. 4 tones will
indicate an attempt to redial.
(Support handsfree profile mobile only. For Nokia
3650, Siemens S55, or equivalent models)
When there is an incoming call and you want to reject it, press the buttons S1 and
hold it until you hear 2 tones, then release it.
While a call is in session, pressing and releasing S2 will increase the speaker
volume; pressing and releasing S3 will decrease the speaker volume on the HS
There is a key tone to indicate volume increase or decrease.
When using a Bluetooth mobile phone:
When using a mobile phone without Bluetooth built-in and requiring a Bluetooth
dongle:
.
!
!
!
200.00 mm
270.00 mm
TM
CS8120 / Abe