NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack MARCY® SMITH MACHINE SM-4008 Assembly Instruction Parts List Warranty Ordering Parts Model SM-4008 Retain This Manual for Reference 100806 OWNER'S MANUAL IMPEX® INC. 2801 S. Towne Ave., Pomona, CA 91766 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN..................................................................……………. IMPORTANT SAFETY NOTICES.................................................................… SMITH MACHINE HARDWARE PACK….......…............................................. SMITH MACHINE ASSEMBLY INSTRUCTIONS............................................ EXPLODED DIAGRAM……………………………………………………………. SMITH MACHINE PARTS LIST………..………………………………………… MULTI-PURPOSE BENCH HARDWARE PACK………………………………..
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
The warning labels shown here have been placed on the Rear Base, and Bench Rear Stabilizer. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
SMITH MACHINE HARDWARE PACK 7
SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Insert a Base Frame (#5) into the Rear Left Vertical Frame (#3). Secure it with two M10 x ¾” Allen Bolts (#90) and two Ø ¾” Washers (#107). C.
STEP 2 (See Diagram 2) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Insert a Guide Rod (#24) into the hole on left Base Frame (#5). Secure it with one M8 x 2 3/8” Allen Bolt (#103), two Ø 5/8” Washers (#106), and one M8 Aircraft Nut (#109). Slide the Left Lower Safety Stop Frame (#26) onto the Guide Rod, and then slide one Safety Stop Frame (#25) onto the Guide Rod. C.) Attach the Front Left Vertical Frame (#1) onto the left Base Frame.
10 STEP 3 (See Diagram 3)
A.) Do not tighten all Nuts and Bolts until instructed to so. B.) Attach the Middle Vertical Frame (#9) under the Rear Top Beam (#6) and onto the Rear Base Frame (#8). C.) Attach the Lower Pulley Frame (#16) to the Middle Vertical Frame from rear. Attach the Foot Plate (#32) to the Middle Vertical Frame from front. Secure them together with two M10 x 3” Carriage Bolts (#89), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110). D.) Attach the Weight Glide Post (#17) to rear of Lower Pulley Frame.
12 STEP 4 (See Diagram 4) A.) Attach the Butterfly Base (#11) to the front of Middle Vertical Frame (#9). Attach the Butterfly Pulley Bracket (#14) to the Middle Vertical Frame.
M10 x 2 ½” Carriage Bolts (#88), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110). B.) Attach the Butterfly Stopper (#31) to Butterfly Base. Secure it with two M6 x 3/8” Allen Bolts (#58). C.) Attach the Backrest Board (#39) to Middle Vertical Frame. Secure it with two M8 x 2 3/8” Allen Bolts (#103) and two Ø 5/8” Washers (#106). DIAGRAM 4 13 STEP 5 (See Diagram 5) A.) Insert the pivot on the Right Butterfly (#13) into the hole on the Butterfly Base from bottom.
(#87). Push the Butterfly Arm Foam Roll (#64) to Right Butterfly. Repeat same step to install the Left Butterfly (#12). B.) Insert two Swivel Pulley Brackets (#15) into the holes on the Butterfly Pulley Bracket (#14). Secure each Swivel Pulley Bracket with one M12 x 5” Hex Bolt (#100), two Ø 1” Washer (#108), and one M12 Aircraft Nut (#111). Do not over tighten the Nuts. Make sure the Brackets are able to swivel.
15 STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of 113” Butterfly Cable (#45) to the clip on Left Butterfly (#12). Draw the Cable to the left Swivel Pulley Bracket (#15).
B.) Attach a Pulley (#62) and two Cable Retainers (#78) to the Bracket. C.) Secure them with one M10 x 2” Allen Bolt (#94), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). D.) Draw the Cable around the Pulley then downward. Attach an Angled Floating Pulley Bracket (#52) to the Cable. Repeat Procedure B above to install a Pulley with two Cable Retainers (#78). Draw the Cable around the Pulley then upward to the right Swivel Pulley Bracket. Let the Bracket hanging for now. E.
A.) Attach the two Cross-over Swivel Pulley Brackets (#10) to left and right Upper Side Frame (#7). Secure each Bracket with four M8 x 3/8” Allen Bolts (#101) and four Ø 5/8” Washers (#106). B.) Remove the U-shaped Connector, Big Washer, and Ball Stopper from one end of 266” Upper Cable (#47). C.) Attach a Pulley (#62) to the left Swivel Bracket and secure it with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). D.
18 DIAGRAM 7-2
19 UPPER CABLE (#47) LOOP DIAGRAM
20 STEP 8 (See Diagram 8 & Cable Loop Diagram)
A.) Attach one end of the 97” Sliding Weight Post Cable (#46) to the Rear Upper Frame (#18). Secure it with one M10 x 2 3/8” Allen Bolt (#118), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). B.) Attach a Pulley (#62) to top holes on the two Double Floating Pulley Brackets (#33). Secure the Pulley with one M10 x 2” Allen Bolt (#94), two Cable Retainers (#78), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#11).
DIAGRAM 8 22
STEP 9 (See Diagram 9) A.) Draw the 152” Lower Cable (#44) through the opening on Foot Plate (#32) to the opening on bottom of Middle Vertical Frame (#9). B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#95), two Ø 1” x ½” Pulley Bushings (#57), and one M10 Aircraft Nut (#110). C.) Draw the Cable under the Pulley and then upward to the Angled Floating Pulley Bracket (#52) previously installed in Step-6. D.) Attach a Pulley to the Bracket.
DIAGRAM 9 24
STEP 10 (See Diagram 10) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#28) in between the two Safety Stop Frames (#25). Align the holes. Insert the Weight Bar (#29) into the Safety Stop Frame from one end and through the Lifting Sleeve to the other Safety Stop Frame on the opposite side. Secure the Weight Bar to Safety Stop Frame with four M8 x 3/8” Allen Screws (#104) pre-installed on the Safety Stop Frame. B.
26
SMITH MACHINE PARTS LIST KEY NO.
MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Front Post (#2) to the Front Stabilizer (#9). Secure it with two M10 x 2 ½” Carriage Bolts (#28), two Ø ¾” Washers (#35), and two M10 Aircraft Nuts (#37). C.
STEP 2 (See Diagram 2) A.) Attach the Incline Support (#8) to the middle side holes on the two Backrest Supports (#7). Secure it with one M10 x 6 7/8” Allen Bolt (#26), two Ø ¾” Washers (#35), and one M10 Aircraft Nut (#37). Do not tighten the Nut and Bolt yet. B.) Attach the bottom side holes on Backrest Supports to the pivot on Main Frame (#1). Secure it with one M10 x 6 7/8” Allen Bolt (#26), two Ø ¾” Washers (#35), and one M10 Aircraft Nut (#37). Securely tighten Nut and Bolt in A & B. C.
STEP 3 (See Diagram 3) A.) Place the Backrest Board (#11) onto the Backrest Supports (#7). Secure it with four M8 x 1 5/8” Allen Bolts (#32) and 5/8” Washers (#36). B.) Place the Seat Pad (#10) onto the two Seat Brackets (#4). Secure it with four M8 x 1 1/8” Allen Bolts (#31) and 5/8” Washers (#36).
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Front Post (#2). Secure it with one M10 x 3” Allen Bolt (#29), two ¾” Washers (#35), and one M10 Aircraft Nut (#37). B.) Insert the Leg Developer Weight Post (#6) into the hole on Leg Developer. Secure it with one M10 x 2 3/8” Allen Bolt (#30), two Ø ¾” Washers (#35), and one M10 Aircraft Nut (#37). Cover the end of the Post with one Ø 1” x Ø 3/8” Washer (#38) and one Ø 1 1/8” x 1 1/8” Rubber Bumper (#20). C.
33
34 MULTI-PURPOSE BENCH PARTS LIST KEY NO.
SM-4008 WEIGHT RESISTANCE CHART Station Ratio Example Low Pulley 100% 10 lb. plate creates 10 lb. resistance Butterfly (both arms) 100% 10 lb. plate creates 5 lb. resistance Left Cross-Over Right Cross-Over 50% 50% 10 lb. plate creates 5 lb resistance 10 lb. plate creates 5 lb resistance *Numbers are approximate. Actual resistance may vary.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
