NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier MARCY PLATINUM MP-2500 HOME GYM Assembly Instruction Parts List Warranty Ordering Parts Model MP-2500 Retain This Manual for Reference 11-06-07 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 7 WEIGHT RESISTANCE CHART.......................................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert two Guide Rods (#17) into the holes on the Rear Stabilizer (#2). Secure each Guide Rod with one M10 x ¾” Allen Bolt (#85) and Ø ¾” Washer (#93) from the bottom. Slide two Ø 2 3/8” Rubber Bumpers (#57) onto the two Guide Rods. B.
DIAGRAM 1 8
STEP 2 (See Diagram 2) A.) Attach the Upper Frame (#15) onto the two Guide Rods (#16). Secure it with two M10 x ¾” Allen Bolts (#85) and ∅ ¾” Washers (#93). DO NOT tighten the Bolts yet. B.) Place the Upper Frame onto the Vertical Frame (#5). Secure it with two M10 x 2 5/8” Carriage Bolts (#90), one 2 ¾” x 4 ¾” Bracket (#23), two ∅ ¾” Washers (#93), and two M10 Aircraft Nuts (#92). C.) Securely tighten all Nuts and Bolts previously installed. D.) Attach the Stopper Frame (#14) to the Vertical Frame.
STEP 3 (See Diagram 3) A.) Attach the Butterfly Base (#13) to the Upper Frame (#15) and the Stopper Frame (#14). Secure it to the Upper Frame with two M10 x 2 5/8” Carriage Bolts (#90), one 2 ¾” x 4 ¾” Bracket (#23), two Ø ¾” Washers (#93), and two M10 Aircraft Nuts (#92). Secure it to the Stopper Frame with two M10 x ¾” Allen Bolts (#85) and Ø ¾” Washers (#93). B.) Attach the Seat Support Frame (#4) onto the Main Base Frame (#1).
STEP 4 (See Diagram 4) A.) Attach the Butterfly Pulley Bracket (#19) to the Vertical Frame (#5). Secure it with one M10 x 3 ½” Allen Bolt (#80), two Ø ¾” Washers (#93), and one M10 Aircraft Nut (#92). B.) Attach two Swivel Pulley Brackets (#10) to the Butterfly Pulley Bracket. Secure each Swivel Pulley Bracket with one M10 x 2 ½” Allen Bolt (#81), two Ø ¾” Washers (#93), and one M10 Aircraft Nut (#92). C.) Attach the Backrest Board (#43) to the Vertical Frame.
STEP 5 (See Diagram 5) A.) Attach the Right & Left Front Press (#7 & #8) onto the Main Base Frame (#1) from both sides. B.) Align the holes. Insert a Front Press Axle (#31) through the holes. Secure the Axle with one Ø1” Washer (#97) and M12 Aircraft Nut (#96) no each side.
STEP 6 (See Diagram 6) A.) Secure the Right Front Press (#7) and the Left Front Press (#8) together with two M10 x 2 ½” Allen Bolts (#81), four Ø ¾” Washers (#93), and two M10 Aircraft Nuts (#92). B.) Attach one Front Press Handle (#20) to the holes on the Right Front Press (#7). Secure it with two M10 x ¾” Allen Bolts (#85) and Ø ¾” Washers (#93). Repeat the same step to install the other side.
Step 7 (See Diagram 7) A.) Insert the axle on the Right Butterfly (#11) through the holes on the Butterfly Base (#13). Cover the axle with a Lock Ring (#44). Secure the Lock Ring to the axle with one M6 x 1 ¼” Allen Bolt (#91) and M6 Aircraft Nut (#95). B.) Push a Butterfly Large Foam Roll (#49) onto the Right Butterfly. Push a Butterfly Foam Roll End Cap (#70) into the end of Right Butterfly. C.) Repeat Procedure A & B above to install the Left Butterfly (#12).
STEP 8 (See Diagram 8 & Upper Cable Loop Diagram) A.) Attach the 108” Upper Cable (#38) to the opening on the front of Upper Frame (#15). Make sure the ball stopper is underneath the Frame. Attach a Pulley (#65) to the Cable. B.) Secure the Pulley to the opening with one M10 x 3 3/8” Allen Bolt (#83), two Ø 7/8” x 1” Pulley Bushings (#55), and one M10 Aircraft Nut (#92). C.) Draw the Cable over the Pulley along the Upper Frame towards the back of the machine to the opening in the middle of Upper Frame.
Upper Cable Loop Diagram 16
STEP 9 (See Diagram 9 & Butterfly Cable Loop Diagram) A.) Clip one end of the 100” Butterfly Cable (#36) onto the Right Butterfly (#11). B.) Draw the Cable to the right open Swivel Pulley Bracket (#10). C.) Attach a Pulley (#65) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#82), two Ø ¾” Washers (#93), and one M10 Aircraft Nut (#92). D.) Draw the Cable over the Pulley then downward. E.) Attach a Pulley to an Angled Double Floating Pulley Bracket (#22). Repeat Procedure C to install a Pulley. F.
Butterfly Cable Loop Diagram 18
STEP 10 (See Diagram 10-1,10-2,10-3, & Lower Cable Loop Diagram)) A.) Attach the 251” Lower Cable (#37) to the open bracket on the Lower Pulley Base Frame (#3). Attach a Pulley (#65) to the bracket. (See Diagram 10-1). B.) Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#82), two Ø ¾” Washers (#93), and one M10 Aircraft Nut (#92). C.) Draw the Cable underneath the Pulley and upward to the open bracket on the Upper Frame (#15). Repeat Procedure B to install a Pulley. D.
DIAGRAM 10-1 20
DAIGRAM 10-2 21
DAIGRAM 10-3 22
Lower Cable Loop Diagram 23
Step 11 (See Diagram 11-1, 11-2, 11-3, 11-4, & Front Press Cable Loop Diagram) A.) Attach the 121” Front Press Cable (#39) to the small tube on the bottom right side of the Vertical Frame (#5). Align the holes then insert a M10 x 5 ½” Allen Bolt (#79) through a Ø ¾” Washer (#93) into the Cable head and the Vertical Frame. (See Diagram 11-1). B.) Draw the Cable to the Left Front Press (#8). Attach a Pulley (#65) to the Cable.
DIAGRAM 11-1 DIAGRAM 11-2 25
DIAGRAM 11-3 DIAGRAM 11-4 26
Front Press Cable Loop Diagram 27
WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Lat Pull 30 40 50 60 70 80 90 100 110 Butterfly 30 40 50 60 70 80 90 100 110 Front Press 30 50 70 90 110 130 150 170 190 Low Pulley 30 40 50 60 70 80 90 100 110 Leg Developer 30 40 50 60 70 80 90 100 110 *Numbers are approximate. Actual weight may vary. *Value for butterfly is for each arm.
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
