NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction MARCY CLASSIC MCB-252 COMBO BENCH W/120 lbs Weight Set Exploded Diagram Parts List Warranty Ordering Parts Model MCB-252 Retain This Manual for Reference 100302 OWNER'S MANUAL IMPEX® INC. 2801 S. Towne Ave., Pomona, CA 91766 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN............................................................................................... IMPORTANT SAFETY NOTICE................................................................................ HARDWARE PACK……............................................................................................ ASSEMBLY INSTRUCTIONS.................................................................................... EXPLODED DIAGRAM................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
ASSEMBLY INSTRUCTION Tools required for assembling the machine: Two Adjustable Wrenches. NOTE: It is strongly recommended that two or more people assemble this equipment to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Secure them with two M10 x 2 ¾” Hex Bolts (#38), one Weight Storage Post (#16), two ¾” Washers (#44), and two M10 Aircraft Nuts (#47) on each end of the Cross Brace. B.
STEP 2 (See Diagram 2) A.) Connect the Front Stabilizer (#5) to the Main Seat Support (#3) and secure them with three M8 x ¾” Hex Bolts (#41) and three Ø 5/8” Washers (#45). DO NOT tighten the Bolts yet. B.) Connect the Main Seat Support to the Cross Brace (#2). Secure it with two M10 x 2 1/8” Bolts (#39), one Bracket (#6), two ¾” Washers (#44), and two M10 Aircraft Nuts (#47). DO NOT tighten the Nuts and Bolts yet. C.) Connect one end of the Diagonal Support (#4) to the Main Seat Support (#3).
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#9) to the open bracket on the Front Stabilizer (#5). Secure it with one M10 x 2 ¾” Hex Bolt (#38), one Ø ¾” Washer (#44), and one M10 Aircraft Nut (#47). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Tubes (#10) halfway through the holes on the Leg Developer. Push four Foam Rolls (#35) onto the Tubes from both ends. C.) Attach a Spring Clip (#36) onto the weight post on the Leg Developer.
STEP 4 (See Diagram 4) A.) Attach the Backrest Supports (#14) onto both ends of the Pivot on the Main Seat Support (#3). Rest the other end against the Backrest Adjustment Bar (#8). B.) Place the Backrest Board (#17) onto the Backrest Supports. Secure it with four M6 x 1 ½” Hex Bolts (#43) and four ½” Washers (#46). C.) Place the Seat Pad (#18) onto the bracket on the Main Seat Support (#3). Align the holes and secure it with four M6 x 1 ¼” Hex Bolts (#27) and four ½” Washers (46). D.
STEP 5 (See Diagram 5) A.) Wrap the ball end of the Cable around the Pulley (#30). Place the Pulley in the open slot on the Lat Bar Frame (#12). Secure it with one M10 x 2” Hex Bolt (#40), two Pulley Bushings (#29), and one M10 Aircraft Nut (#47). B.) Slide the Weight Holder (#11) onto the Lat Bar Frame from the bottom. Connect the Cable to the Holder with a Hook (#32). C.) Connect the Lat Bar (#13) to the Cable with a Hook (#32).
10
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
