NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction MARCY MULTI PURPOSE BENCH MWB-682 Parts List Warranty Ordering Parts Model MWB-682 Retain This Manual for Reference 06-20-06 OWNER'S MANUAL IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICES..................................................................... HARDWARE PACK……….....…....................................................................... ASSEMBLY INSTRUCTIONS........................................................................... EXPLODED DIAGRAM.........................................................................……….
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Rear Stabilizer. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the lable in location shown.
HARDWARE PACK 4
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front Stabilizer (#2). Secure it with two M10 x 2 ¾” Carriage Bolts (#21), one Bracket (#15), two ∅ ¾” Washers (#27), and two M10 Aircraft Nuts (#28). B.) Attach the Main Frame (#1) to the Rear Stabilizer (#3).
STEP 2 (See Diagram 2) A.) Slide the Sliding Block (#5) onto the Incline Adjustment Bar (#4). B.) Attach both ends of Incline Adjustment Bar to the open brackets on the Main Frame (#1). Secure each end with one M10 x 2 ½” Carriage Bolt (#22), Ø ¾” Washer (#27), and M10 Aircraft Nut (#28). C.) Use a Lock Knob (#16) to lock the desired incline position. D.) Attach the Handle (#29) to the Main Frame. Secure it with one M10 x ¾” Allen Bolt (#33) and Ø ¾” Washer (#27).
STEP 3 (See Diagram 3) A.) Attach the lower holes on the Backrest Supports (#7) to the pivot on the Sliding Block (#5). Secure them with one M12 x 6 ½” Allen Bolt (#19), two ∅ 1” Washers (#25), and one M12 Aircraft Nut (#26). B.) Attach the Seat Support Frame (#6) to the hole on the Backrest Support (#7). Make sure the Seat Support Frame is on the outside of the Backrest Support. Align the holes and secure them with one M12 x 2 ½” Allen Bolt (#20), two Ø 1” Washers (#25), and one M12 Aircraft Nut (#26).
STEP 4 (See Diagram 4) A.) Insert the Foam Tube (#10) halfway through the hole on the Main Frame (#1). Push two Vinyl Foam Rolls (#12) onto the Foam Tube from both ends. Plug the Foam Roll End Caps (#11) into the ends. B.) Place the Seat (#8) onto the Seat Support Frames (#6). Secure it with four M8 x 2” Allen Bolts (#23) and ∅ 5/8” Washers (#24). C.) Place the Backrest Board (#9) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#23) and ∅ 5/8” Washers (#24).
EXPLODED DIAGRAM 9
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
