NOTE: Please read all instructions carefully before using this product Safety Notice Hardware Identifier APEX POWER TOWER TC-2210 Assembly Instruction Parts List Warranty Ordering Parts Model TC-2210 Retain This Manual for Reference 4-14-08 OWNER'S MANUAL IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICES..................................................................... HARDWARE IDENTIFIER.....…....................................................................... ASSEMBLY INSTRUCTIONS........................................................................... EXPLODED DIAGRAM……………………………………………………………… PARTS LIST....................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Base Frame. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE PACK 4
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left and Right Base Frame (#1 & #2) with the Stabilizer (#3) in the mid-span. Secure each end with two M10 x 2 ¾” Carriage Bolts (#19), ∅ ¾” Washers (#17), and M10 Aircraft Nuts (#18). Do NOT tighten the Nuts and Bolts yet. B.
STEP 2 (See Diagram 2) A.) Attach a Diagonal Support (#4) to the Lower Upright Beam (#5) and the Right Base Frame (#2). Secure it to the Lower Upright Beam with two M10 x 3” Carriage Bolts (#20), Ø 1 ¼” Bent Washers (#22), and M10 Aircraft Nuts (#18). Secure it to the Right Base Frame with two M10 x 2 ¾” Carriage Bolts (#19), one 4 ¾” Bracket (#13), two Ø ¾” Washers (#17), and two M10 Aircraft Nuts (#18). B.) Attach a Dip Support (#9) to the Lower Upright Beam.
DIAGRAM 2 7
STEP 3 (See Diagram 3) A.) Attach the Chin-up Bar (#10) to the top opening on the two Upper Upright Beams. Secure the Chin-up Bar to each opening with one M8 x 1 5/8” Allen Bolt (#27) and Ø ½” Bent Washer (#34). Cover each opening with an Upright Beam End Cap (#30). B.) Attach the two Arm Pads (#15) onto the Dip Supports. Secure each Arm Pad with two M8 x 2 ½” Allen Bolts (#16) and Ø 5/8” Bent Washers (#26). C.) Attach the Backrest Board (#14) to the Cross Brace (#7).
EXPLODED DIAGRAM 9
Parts list KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
