User Manual

ManualsBrandsImpact ManualsLighting & StudioPowerSync16 DC Receiver

20-page manual to be inserted into packaging for AC and DC model receivers

10M 25M 50M 75M 100M 10Y 25Y 50Y 75Y 100Y

One-Year Limited Warranty

Introduction

Thank you for choosing the PowerSync Radio Slave System, designed

using the latest technology to produce a device that is simple to

operate, while providing photographers with the highest quality radio

slave system at an affordable price. The PowerSync System is

designed strictly for ash units. It cannot be used with hot lights or

continuous light sources. The PowerSync System allows the

photographer to trigger the light source wirelessly from the camera

(ts most cameras). It can also be used to trigger a remote camera

that has an electronic shutter release connection. Remote shutter

triggering requires a compatible motor drive cable (see Accessories).

The PowerSync Radio Slave System is available in two versions. The

AC 100-240 volt version must be plugged into a wall socket. The DC

version works with two standard AA batteries. The DC Receiver will

also accept an AC adapter (DC 7V-9V/300mA). The Transmitter can be

used for either model and operates on one 3V CR2450 battery. You

must have both a Transmitter and either model of Receiver for the

system to work. Your Transmitter can trigger as many Receivers as

you want. As long as all Receivers are within range, and are set to the

same frequency as the Transmitter, your Transmitter can trigger as

many lights as your setup requires.

In order to fully understand your new PowerSync Radio Slave System,

please take a moment to read through this user guide.

20-page manual to be inserted into packaging for AC and DC model receivers

10M 25M 50M 75M 100M 10Y 25Y 50Y 75Y 100Y

Backward Compatibility

The PowerSync 16-80 is backward compatible with the PowerSync 16

Radio Slave System.

PowerSync 16 Transmitter to PowerSync 16-80 as Receiver:

The PowerSync 16 transmitter can be used to trigger the PowerSync

16-80. Set your PowerSync 16-80 to Receiver (Rx) or

Transmitter/Receiver (Tx/Rx) mode using the M button to accept a

signal from the PowerSync 16 transmitter. Ensure the channel on both

devices is identical. See chart below.

PowerSync 16-80 Transmitter to PowerSync 16 as Receiver:

The PowerSync 16-80 can be used to trigger the PowerSync 16

receiver. Set your PowerSync 16-80 to Transmitter (Tx) or

Transmitter/Receiver (Tx/Rx) mode using the M button to send a signal.

Ensure the channel on both devices is identical. See chart below.

For channel selection, the PowerSync 16 system relies on manual

channel selector switches. Despite the PowerSync 16-80’s digital

interface, channels on the two devices can be synchronized using the

chart below as a guide

Note: When using the PowerSync 16 – only 16 channels are available.

The PowerSync 16-80’s backward compatibility with the PowerSync 16

system will only work if No Group is selected on the PowerSync 16-80.

This IMPACT product is warranted to the original purchaser to be free

from defects in materials and workmanship under normal consumer use

for a period of one (1) year from the original purchase date or thirty (30)

days after replacement, whichever occurs later. The warranty provider’s

responsibility with respect to this limited warranty shall be limited solely to

repair or replacement, at the provider’s discretion, of any product that fails

during normal use of this product in its intended manner and in its intended

environment. Inoperability of the product or part(s) shall be determined by

the warranty provider. If the product has been discontinued, the warranty

provider reserves the right to replace it with a model of equivalent quality and

function.

This warranty does not cover damage or defect caused by misuse, neglect,

accident, alteration, abuse, improper installation or maintenance. EXCEPT

AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY

EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING

BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with

specic legal rights, and you may also have additional rights that vary from

state to state.

To obtain warranty coverage, contact the Impact Customer Service

Department to obtain a return merchandise authorization (“RMA”) number,

and return the defective product to Impact along with the RMA number and

proof of purchase. Shipment of the defective product is at the purchaser’s

own risk and expense.

For more information or to arrange service,

visit www.impactstudiolighting.com or call Customer Service at 212-594-2353.

Product warranty provided by the Gradus Group. www.gradusgroup.com

IMPACT is a registered trademark of the Gradus Group.