User Manual

ManualsBrandsImpact ManualsLighting & StudioPowerSync16 AC Receiver

PowerSync

Radio Slave

INSTRUCTIONS

10M 25M 50M 75M 100M 10Y 25Y 50Y 75Y 100Y

20-page manual to be inserted into packaging for AC and DC model receivers

Folds to 82 x 110 mm

impact

One-Year Limited Warranty

This IMPACT product is warranted to the original purchaser to be free from

defects in materials and workmanship under normal consumer use for a period of

one (1) year from the original purchase date or thirty (30) days after replacement,

whichever occurs later. The warranty provider’s responsibility with respect to

this limited warrant y shall be limited solely to repair or replacement, at the

provider’s discretion, of any product that fails during normal use of this product in

its intended manner and in its intended environment. Inoperability of the product

or part(s) shall be determined by the warranty provider. If the product has been

discontinued, the warranty provider reserves the right to replace it with a model

of equivalent quality and function.

This warranty does not cover damage or defect caused by misuse, neglect,

accident, alteration, abuse, improper installation or maintenance. EXCEPT AS

PROVIDED HEREIN, THE WARRANT Y PROVIDER MAKES NEITHER ANY

EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT

NOT LIMITED TO ANY IMPLIED WARRANY OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. This warranty provides you with specic legal

rights, and you may also have additional rights that vary from state to state.

To obtain warranty coverage, contact the Impact Customer Service Department

to obtain a return merchandise authorization (“RMA”) number, and return the

defective product to Impact along with the RMA number and proof of purchase.

Shipment of the defective product is at the purchaser’s own risk and expense.

For more information or to arrange service, visit www.impactstudiolighting.com

or call Customer Service at 212-594-2353.

Product warranty is provided by the Gradus Group.

www.gradusgroup.com

Impact is a registered trademark of the Gradus Group.

All other trademarks are the property of their respective owners

GG3

Summary of content (20 pages)

PAGE 1
impact TM PowerSync16 Radio Slave INSTRUCTIONS
PAGE 2
Introduction Thank you for choosing the PowerSync Radio Slave System, designed using the latest technology to produce a device that is simple to operate, while providing photographers with the highest quality radio slave system at an affordable price. The PowerSync System is designed strictly for flash units. It cannot be used with hot lights or continuous light sources. The PowerSync System allows the photographer to trigger the light source wirelessly from the camera (fits most cameras).
PAGE 3
Key Features • 16 Reliable Channels: Digitally coded at 2.4 GHz for multiple setups; work at events with other photographers without the worry of flash or radio interference. • Extensive Range of Reliable Performance: 590 feet (180 m) indoors; 200+ feet (60+ m) outdoors. An above-average range for the most demanding situations (radio interference and low battery strength will lower your effective range).
PAGE 4
PowerSync16 AC Receiver Signal confirmation LED Antenna Lanyard hook 1/8˝ mini (3.5 mm) sync jack Power LED AC Power Input 100V~240V AC power output 16-channel selector Sync cord 3.5 to 6.
PAGE 5
PowerSync16 DC Receiver Signal confirmation LED Lanyard hole Antenna Power switch 1/8˝ mini (3.5 mm) sync jack Female PC jack 1/4˝-20 female threads Power LED Hotshoe mount Battery bay 16-channel selector AC adapter input Sync cord Adhesive-backed accessory shoes (2) 3.5 to 6.
PAGE 6
PowerSync16 Transmitter Power switch Lanyard hole 2.5mm sub-mini jack Antenna Signal confirmation LED Battery bay Hot shoe with locking thumbwheel PC male to 1/8˝ (2.
PAGE 7
Safety Warnings • Do not remove instrument covers during operation. • Do not operate the PowerSync System in the presence of flammable gases or fumes. Operation of any electrical instrument in such an environment creates an extreme safety hazard. • There are no user-serviceable parts inside the PowerSync Transmitter and Receiver systems. Do not install substitute parts or perform any unauthorized modification of either the Transmitter or Receiver. • PowerSync is an accessory device for flash photography.
PAGE 8
Step 1: Synchronizing Channels For your PowerSync system to work properly, both the Transmitter and Receiver must be set to use the same channel. The battery cover on the Transmitter features a pin for changing the DIP switches. With both units switched OFF, set the DIP switches to the same configuration on each. There are 16 different possible configurations. Turn ON both the Transmitter and Receiver. The Transmitter has a test button which you can use to confirm your set-up.
PAGE 9
Step 2: Setting Up the Transmitter There are two methods to connect the Transmitter to your camera: Hot-shoe mount One method is to affix the Transmitter to the hot shoe of your camera. Slide the Transmitter into the hot shoe. The test button should be at the back, the same side as the viewfinder. Tighten the lock wheel. Sync cable The other method is to connect the supplied sub-mini (2.
PAGE 10
Step 3: Setting Up the Receiver (DC Model) If using a portable flash unit, you can attach the flash directly to the DC Receiver’s hot shoe. With the 1/4˝ female threads on the back of the DC Receiver, you can then mount your remote flash on a tripod or a light stand with an adapter. You can also use the DC Receiver’s sync cord to connect directly to a studio flash.
PAGE 11
Step 3: Setting Up the Receiver (AC Model) • Be sure your flash head is turned OFF. Unplug the power cord from the wall socket. • Unplug the AC power cord from the flash (either the power pack or mono light) and plug it into the bottom of the PowerSync AC Receiver. • Insert the power cord of the receiver into the AC power socket of the flash. • Then insert the sync cord of the receiver into the sync socket of the flash.
PAGE 12
Step 4: Mounting the Receiver Shoe mount 1/4˝-20 mount There are many ways you can mount your PowerSync Receiver to your flash unit. Attach an adhesivebacked accessory shoe to your flash and the shoe-to-1/4˝-20 adapter to your Receiver. Or use the Receiver’s 1/4˝-20 female threads to mount the Receiver to a light stand or mounting arm. You can also thread a lanyard through the lanyard hole and hang the Receiver from a light stand, flash handle, or anywhere else convenient.
PAGE 13
Triggering a Remote Camera You can use your PowerSync System to trigger a remote camera. The camera must have an electronic shutter release connection, and you must have a compatible camera release cable (see Accessories). Step 1: Connect your PowerSync DC Receiver to the electronic shutter release connection on your camera using a compatible camera release cable. Step 2: Make certain that both your PowerSync DC Receiver and Transmitter are set to the same channel and are powered up.
PAGE 14
Accessories: Sync Cables Your PowerSync Radio Slave system is compatible with a wide variety of cameras and flash units right out of the box, but you may need an accessory sync cable for some cameras and/or flash units. Below are the plug ends commonly in use and the equipment they typically connect. Verify the plug compatible with your equipment. PC Standard Fits most professional cameras. 2.5 mm Sub-Miniphone This plug is typically used only on slave systems.
PAGE 15
Accessories: Miscellaneous To use your PowerSync System to trigger your camera shutter, you’ll need a Camera Release Cable compatible with your camera. Please see the included cable compatibility insert card.
PAGE 16
Troubleshooting 1. Turn OFF the Receiver (if it’s a DC Receiver) and verify that the batteries’ polarity is correct. Turn the Receiver back to the ON position. 2. Make sure the batteries in the Transmitter are fresh. Weak batteries will reduce the distance over which a transmission can be made. 3. Ensure that both the PowerSync Transmitter and Receiver are connected properly. 4. Make sure that both the Transmitter and Receiver are set to the same channel. 5.
PAGE 17
10M 25M Specifications 2.4 GHz Channels: 16 digitally-coded channels Operating Range: ~590 feet (~180 meters) indoors +200 feet (+60 meters) outdoors 50M Frequency: 75M Sync Speed: Trigger Speed: 100M Sync Jacks: 1/250 second maximum 8 frames/second maximum 10Y Transmitter – 2.5 mm sub-mini female DC Receiver – 1/8˝ mini (3.5 mm) female PC female hot shoe female AC Receiver – 1/8˝ mini (3.5 mm) female Transmitter Trigger: 3 V DC Transmitter – 1 × CR2450 DC Receiver – 2 × AA 1.
PAGE 18
Backward Compatibility The PowerSync 16-80 is backward compatible with the PowerSync 16 Radio Slave System. PowerSync 16 Transmitter to PowerSync 16-80 as Receiver: The PowerSync 16 transmitter can be used to trigger the PowerSync 16-80. Set your PowerSync 16-80 to Receiver (Rx) or Transmitter/Receiver (Tx/Rx) mode using the M button to accept a signal from the PowerSync 16 transmitter. Ensure the channel on both devices is identical. See chart below.
PAGE 19
10M 25M One-Year Limited Warranty 50M This IMPACT product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
PAGE 20
GG3