PCSLEDK-110 Pro Copy Stand with Dual LED Panel Light Kit INSTRUCTIONS
Introduction Thank you for choosing Impact. The Impact Pro Copy Stand allows you to accurately and repeatedly shoot products or documents. It provides an alignment grid, top-down shooting platform, and dual LED lighting. The grid makes it easy to align each shot and take the same image again and again. A shooting platform offers a top-down angle over your subject and is mounted on an adjustable 42-inch sliding column.
Specifications Baseboard finish 18% matte gray Grid Yes Column height 42 in. (106.7 cm) Camera mount 1/4-20 3/8-16 bushing Weight capacity 8 lb. (3.6 kg) Clamp width 1.45 in. (3.7 cm) Light type LED LED count 96 each Max output 20 W Color temp 5600 K CRI 95 Beam angle 120° Light intensity @ 1 ft. (30.5 cm): 5213 lx / 484.3 fc @ 3 ft. (91.4 cm): 656 lx / 60.9 fc Voltage 100–240 V AC Avg lamp life 50,000 hr. Max document size 16 × 20 in. (40.6 × 50.
Overview 1. Hex key holder 2. Slide column 3. Camera mounting screw with 1/4-20 thread and 3/8-16 bushing 4. Mounting screw cap 5. Platform extension 6. Camera mount 7. Camera platform 8. Quick-release handle 9. Horizontal support (×2) 10. Horizontal support adapter 11. Vertical adjustment locking knob 12. Vertical support (×2) 13. Clamp locking knob 14. Pivot locking knob Additional Hardware • 17 mm short extension screws • 17 mm washers • Spare backstop screw and spacer 4 15. 16. 17. 18. 19. 20. 21.
1 2 3 10 4 6 5 7 19 8 11 20 21 9 22 23 24 25 13 14 12 15 16 17 18 28 26 29 27 5
Setup Base and Slide Column Assembly 1. Remove the hex key from its storage holder on top of the sliding column. 1 2. Use the hex screws and washers to attach the baseplate, baseboard, and slide column. Make sure the camera platform is positioned over the baseboard. Use the hex key to tighten until secure.
Table Clamp / Light Assembly Follow these instructions for both support arms. 1. Unscrew and remove the clamp’s pivot locking knob. 1 2. Align the vertical support with the clamp. Screw the pivot locking knob through the washer and into the clamp assembly. Tighten until secure. 2 3. Loosen the clamp locking knob, and fit the clamp onto the baseboard, one support arm on each side of the sliding column. Tighten until secure.
4. Slide the horizontal support’s adapter over the vertical support. Tighten the adapter’s locking knob until secure. 4 5. Loosen the LED’s support adapter, and slide it over the horizontal support. Tighten until secure. 5 6. Plug each of the LED panels into a power source, and press the power switches to On.
Mounting a Camera 1. Unscrew the mounting screw cap to reveal the 3/8-16 bushing. Remove the bushing to reveal the 1/4-20 threaded screw. 1 2. Align and mount your camera onto the 3/8-16 or 1/4-20 threaded screw. Tighten until secure. 2 3. Press the quick release handle to raise or lower your camera. Release to lock in place.
Removing the Camera Platform Extension The camera platform extension can be removed to accommodate a larger camera setup. 1. Use the hex key to remove the three screws from the front of the camera platform, and then remove the platform extension. 1 2. Screw in the three provided 17 mm short extension screws to secure the camera mount to the platform.
Adjustments Camera height Lighting support pivot LED panel tilt Lighting support vertical LED panel rotation and horizontal adjustment 11
One-Year Limited Warranty This Impact product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
