Users Manual

And also check if the message can show up on your phone's
notification bar or not. If not, please allow the APP notifications
to pop-up in the notification bar in the system setting: Setting-
Notifications- Notification style-Tick the "Banners".
If the messages can still not be displayed on the watch even
after trying the above steps, please exit the
Gl
oryFit
APP and
restart the mobile phone and the watch.
3. How to synchronize the watch data to my phone?
Auto synchronization: When the watch is connected to the APP,
it will automatically synchronize data;
Manual synchronization: After the watch is connected to the
APP successfully, you can manually synchronize the data by
swiping down the screen from the APP homepage or data
interface;
If the data cannot be synchronized, please try to disable and
enable the Bluetooth function again on your mobile phone, or
restart your mobile phone;
(Note: In case of any common problems in operation, please
refer to the Common problem in My profile of the APP, which can
help you solve some problems) As shown in the figure below:
KW66
User Manual
CONTENTS
English 01-07
Read this manual carefully before use, and retain it for future reference.
Product Introduction
Touch screen
Wrist strap
Charging port
Heart rate sensor
Charging cable
Power button
(Press and hold
the Power
button for 5
seconds to turn
it on Press the
power button
to wake the
screen or return
to the previous
interface）
Wearing
Wear the wristband about one finger away from the wrist bone
and adjust the tightness of the wristband to a comfortable
position.
Tip: If you wear the strap too loose, the data acquisition of heart
rate sensor may be affected.
Connection and binding
1. Scan the QR code on the watch display (Settings-APP
Download) by your mobile phone, and then install the APP Runto
Sport. You can also scan the QR code below to download and
install GloryFit from the mobile APP store.
EN-01
EN-02 EN-03
EN-04 EN-05
EN-06 EN-07
FCC ID: 2APA9-IMILAB-KW66
Model: KW66
MADE IN CHINA
2. After installing the APP, open and log in GloryFit, then select
(device KW66 to be added) on the device page so as to connect
it.
In the process of pairing, check if the Bluetooth functionon
your mobile phone is enabled, so that the watch can be
connected to your mobile phone.
If the device cannot be found in the pairing process, or the
device cannot be connected during use, please click
"Settings - Reset" on the watch, then try to start the pairing again.
If the watch still can not be found, please exit and re-open the
APP.
The connection status of the watch is as shown in the figures
below :
Tips:
Operation
1. Open the control panel: Swipe the screen on the main interface
downwards from the top
2. Open the messages/notifications: Swipe the screen on the
main interface upwards from the bottom
3. Open the main menu:Swipe the screen on the main interface
from left to right (Note: On other interfaces, slide your finger
from left to right to return to the previous interface)
4. Open the status interface: Swipe the screen on the main
interface from right to left
5. Quick dial change: Press and hold the dial interface for 3
seconds, and the watch vibrates once; then you can slide your
finger to left or right to select the dial.
6. Power on: Press and hold the Power button for 5 seconds to
switch it on (Power off: You need to press and hold the button
for 3 seconds when the display is on to select whether to power
off)
7. Quick sports pause/continue: Press the power button.
8. Press the power button to return to the homepage (Note: If
you are on the level 2 interface, you will return to the level 1
interface).
Note: The battery power will be shown as 5 different levels on
the watch (0%-25%-50%-75%-100%)
Not connected Connected
Features
13 sport modes
(Running, Walking,
Cycling, Alpinism, Yoga,
Skipping, Tennis,
Baseball, Basketball,
Badminton, Football,
Rugby, Table Tennis)
In running, walking,
Alpinism and other
sports modes, you can
click the screen to view
the sports data (steps,
pace, calories, distance
and duration).
Heart Rate Monitor: The
watch will continuously
track your heart rate for
24 hours(Need to turn on
the “Heart rate
monitoring” in the APP
at first), you can also
view the historical heart
rate data in the APP.
Note: When this feature
is enabled, the power
consumption will be
increased, and the
battery endurance will
be reduced.
Status Interface: The
steps, distance and
calories will be recorded
in detail and displayed
on watch everyday.
Sleep: The watch will monitor
your sleep status from 6:00 pm
to the 11:59 am of the next day.
Note: The sleep data on watch
will be cleared at 6:00pm
everyday. But you still can check
the historical sleep data in the
GloryFit APP.
Music: The watch can be used to
control the music player of the
mobile phone, you can use it to
play/pause or skip songs (it is
only compatible with the in-built
music player of the mobile
phone, may not be compatible
with third party’s player, and the
volume cannot be adjusted on
the watch)
Stopwatch: The watch can be
used to count time (slide your
finger to the right after pressing
the pause button to exit and
return to the previous menu)
Message: The watch will receive
and display texts/ messages/
social media notifications from
your phone.
Setting: You can shut down or
reset the watch from setting, and
you can also check the info
about the watch and App
download QR code.
Charging
1. Place the watch on the magnetic charger, please make sure
the charging contacts on the back of the watch are fully
adsorbed the metal contacts of the charger. It can be fully
charged within about 3.5 hours.
2. Plug the charging cable into a standard USB charger
purchased via official channels. The output voltage is 5V and the
output current is 1A.
If the watch cannot be turned on after being out of use for a
long time, please wipe the charging contacts of the charging
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician
for help
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
cable when using it again to remove the sweat or moisture
residue.
Note: (If you do not use the watch often, please charge it once
every month.)
Basic parameters
FAQ
1. The watch can not be connected to the APP.(Or the watch cant
be found by the APP)
Please make sure the software version of your smart phone is
over Android 4.4 Or iOS 7.0.
Please check whether the watch was connected to another
phone or not, if yes please unbind it at first.
Please make sure you have enabled the Bluetooth function of
your phone. (If it's still not working, we recommend you to exit
all of other APP and reopen the Bluetooth function)
If the watch still cant be connected even after trying the above
steps, please exit the
Gl
oryFit
APP and restart the mobile phone
and the watch.
*Note:Some smart phones will not be connected to the watch in
low battery mode.
2. Can’t get any text/message on the watch
First, please make sure the Bluetooth function is enabled on
your mobile phone, and check whether the watch is connected
successfully with your phone through the
Gl
oryFit
APP. Then turn
on the "Notifications reminders" in the APP.
Then please check whether you give this APP the permission to
keep running in the background on your mobile phone. If not,
please allow it to keep running in the background.
Display
Touch screen
Material of shell
Material of strap
Battery and
battery life
Button
Charging mode
Water-proofing
Standby time>30 days
Service time: 7 days (with all features on)
Power button on side
Magnetic charging
IPX8 waterproof level
1.28inch TFT 240*240
Capacitive full touch screen
Zinc alloy with vacuum plating
Silicone rubber
340mAh lithium polymer battery
Hardware parameters
Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.