McPC 100Mbps (PCI Version) Operation Manual
FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents FCC Radio Frequency Interference Statement ....................................................ii Warranty............................................................................................................ii About the McPC 100Mbps.................................................................................1 LED Indicators....................................................................................................3 LinkLoss and FiberAlert ................................
About the McPC 100Mbps The McPC 100Mbps is an IEEE 802.3 single-conversion PC media converter card designed to convert twisted pair (100Base-TX) connections to a variety of other fiber connections: 100 Base-SX 850 or 1300nm multi-mode or 100Base-FX 1310nm or 1550nm single-mode. Single strand versions are also available. The McPC 100Mbps can be installed in any PC with a standard PCI slot. It includes diagnostic LEDs for each port, and a 4-pin peripheral power supply connector.
NOTE The default for all features except Auto Negotiation is "Disabled." Jumper Settings Feature Jumper Position ON (pins) OFF (pins) Factory Default JP2 TXLL 1-2 2-3 OFF JP3 FXLL 1-2 2-3 OFF AutoCross The McPC 100Mbps includes AutoCross, a feature which automatically selects between a crossover workstation or a straight-through/repeater hub connection depending on the connected device. Auto Negotiation on McPC 100Mbps Auto Negotiation is available on the McPC 100Mbps.
Enabling Auto Negotiation Configure Auto Negotiation on the McPC 100Mbps by adjusting a two-position switch, labeled AN, on the faceplate next to the fiber connectors. Enable this feature by moving the switch to the up ON position. Disable (default) by moving the switch to the down OFF position. LED Indicators The McPC 100Mbps features four diagnostic LEDs.
The McPC 100Mbps also sends out link pulses from its copper and fiber transmitters, but normally has no way of knowing whether the cable to the other device is intact and the link pulses are reaching the other end. The combination of FiberAlert and LinkLoss allows this information to be obtained, even when physical access to a remote device (and its link integrity LED) is not available. FX LinkLoss (FXLL) FX LinkLoss is a troubleshooting feature.
Enabling TX and FX LinkLoss In order to enable the LinkLoss features, remove the cover from the unit and place the jumpers accordingly. Follow the instructions below, referencing the diagram. 1. 2. 3. 4. Make sure that there is no power going to the unit by UNPLUGGING THE POWER CORD. Using a Philllips screwdriver, remove the screws on the corners of the cover. Remove the cover and find the three-pin jumper blocks for TX and FX LinkLoss. Adjust the shunts on the jumpers accordingly.
Installation Troubleshooting During installation, first test the fiber and twisted pair connections with FiberAlert disabled. Then enable FiberAlert, if desired, just before final installation. This will reduce the feature’s interference with testing. To test McPC 100Mbps by itself, use the appropriate fiber patch cable. First, connect McPC 100Mbps to the twisted pair device with a twisted pair cable.
Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, which can obstruct the optic path and cause performance degradation. Good system performance requires clean optics and connector ferrules. 1. Use fiber patch cords (or connectors, if you terminate your own fiber) only from a reputable supplier; low-quality components can cause many hard-to-diagnose problems in an installation. 2.
Safety Certifications UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment. CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (2004/108/EC) and the Council Directive on Electrical Equipment Designed for use within Certain Voltage Limits (2006/95/EC). Certified to Safety of Information Technology Equipment, Including Electrical Business Equipment. For further details, contact IMC Networks.
19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2009 IMC Networks. All rights reserved. The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any errors that may appear in this document. McPC 100Mbps is a trademark of IMC Networks. Other brands or product names may be trademarks and are the property of their respective companies.
