IE-MediaChassis/1-DC Operation Manual
FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Table of Contents FCC Radio Frequency Interference Statement ........................................................ ii Warranty................................................................................................................ ii About the IE-MediaChassis/1-DC ...........................................................................1 Installing the IE-MediaChassis/1-DC .......................................................................1 Rackmount Precautions.............................
About the IE-MediaChassis/1-DC The IE-MediaChassis/1-DC is a stand-alone chassis for use with iMcV modules. As an unmanaged chassis, the IE-MediaChassis/1-DC supports a single-wide iMcV module. All iMcV modules, with the exception of the SNMP management card, will function properly in this chassis. The IE-MediaChassis/1-DC contains an internal Telco compatible DC power supply.
Rackmount Precautions 1. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. 2.
Configuring and Installing Modules IMC Networks recommends disconnecting the chassis power before proceeding. 1. To install an iMcV module, slide the module into the chassis until the module is firmly seated in the backplane. 2. Secure the module to the chassis by tightening the captive thumb screw on the iMcV module. 3. Attach the network cables between the iMcV module and other devices that will be interconnected. 4. Connect the DC power source.
This equipment is designed to permit the connection of the grounded conductor of the DC supply circuit to the grounded conductor at the equipment. If this connection is made, all of the following conditions must be met: 1. This equipment shall be connected directly to the DC supply system grounded electrode conductor or to a bonding jumper from a grounded terminal bar or bus to which the DC supply system grounding electrode conductor is connected. 2.
DC Power Supply Precautions The following precautions must be observed when installing this chassis. 1. 2. Check nameplate ratings to ensure there is no overloading of supply circuits that could effect over current protection and supply wiring. In addition, the following must be observed: a. Connect the equipment to a 35 to 75 VDC power source that is electrically isolated from the alternating current source. b.
IMC Networks Technical Support Tel: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada); +32-16-550880 (Europe) Fax: (949) 465-3020 E-Mail: techsupport@imcnetworks.com Web: www.imcnetworks.
Electrostatic Discharge Precautions Electrostatic discharge (ESD) can cause damage to your add-in modules. Always observe the following precautions when installing or handling an add-in module or any board assembly. 1. Do not remove unit from its protective packaging until you’re ready to install it. 2. Wear an ESD wrist grounding strap before handling any module or component.
Safety Certifications UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment. CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (89/336/EEC) and the Council Directive on Electrical Equipment Designed for use within Certain Voltage Limits (73/23/EEC). Certified to Safety of Information Technology Equipment, Including Electrical Business Equipment. For further details, contact IMC Networks.
19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2008 IMC Networks. All rights reserved. The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any errors that may appear in this document. IE-MediaChassis/1-DC is a trademark of IMC Networks. Other brands or product names may be trademarks and are the property of their respective companies.
