User Manual

General
• Preserves complete end-to-end fiber
connection integrity
• Bi-directional bandwidth control
• Read/write IEEE 802.1Q VLAN-tags
• Supports Extra Tagging (Q-in-Q)
• QoS: IEEE 802.1p-based packet pri-
oritization (2 queues [high/low] with 8
levels of priority)
• Layer 2 packet switching, store and for-
ward operation
• Forwarding rate: 14,880pps for 10
Mbps; 148,800pps for 100 Mbps;
• AutoCross for MDI-II/MDI-X
• Features Auto-Negotiation and
Selective Advertising
• Supports Half and Full-Duplex operation
• MTU: Supports over-sized packets up to
1916 bytes per packet
Security
• Password Control
• Multiple Access Levels: User Assigned
Accounts & Access Levels
Management
• SNMP V1 and V2c compatible
• Includes GUI-based iView² software for
remote management and upgrades
• Monitors far-end (remote) status without
a physical presence or separate con-
nection
• IEEE 802.3x Flow Control
• Includes DHCP and TFTP clients
• Supports Telnet
• Includes loopback test modes (MAC
swap)
• Includes LinkLoss and FiberAlert
• Supports the Unified Management
Agent (UMA)
• Includes status LEDs
• RS-232 (Craft) interface for local man-
agement
• Serial cable for direct connection to a
PC’s Serial Port
Ethernet Types Supported
• IEEE 802.3i 10Base-T twisted pair
• IEEE 802.3u 100Base-TX twisted pair
• IEEE 802.3u 100Base-FX or SX fiber
Technical Specifications
Network operators can deploy a single
IE-MiniFiberLinX-II in stand-alone applications.
At the Central Office (CO), a fiber switch connects
via a fiber cable to the IE-MiniFiberLinX-II at the
customer premises. The IE-MiniFiberLinX-II can
be managed from the CO over SNMP or Telnet.
The IE-MiniFiberLinX-II is very versatile and
offers a range of AC and DC powering options.
It also supports 802.3af powering functionality,
allowing it to act as a Powered Device (PD).
The IE-MiniFiberLinX-II can be powered from
a PSE-enabled wireless Access Point, which in
turn can be powered by a remote source such
as the solar panels on a street light. The data
is transmitted over fiber to an iMediaChassis/20
with iMcV modules in the Central Office to form an
end-to-end managed system.
Typical Application— Single
IE-MiniFiberLinX-II Solution
Application Examples (cont.)
Typical Application— Powering
Options
NID Application
Networking
RoHS Compliant
Fiber Types Supported
• 50/125µm or 62.5/125µm multi-mode fiber
• 9/125µm single-mode fiber
• Single-strand fiber or CWDM
Connectors: RJ-45, and ST or SC Includes
DIN clips for mounting
Shipping Weight: 0.30 lbs (0.11 kg)
Dimensions: 0.83”H x 1.80”W x 3.35”D (2.11 x
4.57 x 8.51 cm)
Environmental
• Humidity: 5 - 95% (non-condensing)
• Operating Temperature: -49° to +158°F (-35°
to +70°C) excluding AC wall adapter; with
AC wall adapter: 32° to 122°F (0° to 40°C)
• Storage Temperature: -49° to 185° F (-45°
to +85° C)
Power
• AC Wall Adapter: 100/240 ±10% VAC input,
5VDC output
• DC Input Voltage: 750mA@5V
• IEEE 802.3af Power over Ethernet
Physical Specifications