Owner’s manual
Safety instructions 1. R ead these instructions – All the safety and operating instructions should be read before this product is operated. 2. K eep these instructions – The safety and operating instructions should be retained for future reference. 3. Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow all instructions – All operating and use instructions should be followed. 5.
Contents Getting started............................................................................. 4 Remote control setup......................................................................................................4 Network setup.................................................................................................................4 Wireless setup.................................................................................................................5 Wired setup...............
Getting started Remote control setup Pull the plastic tab from the remote control battery compartment and remove the protective film from remote buttons. Network setup Contour 200i Air can be connected to your network by using a wireless or wired connection. The wireless connection method is very flexible as it does not require an Ethernet cable to be run between Contour 200i Air and your wireless router, allowing you to position your Contour 200i Air anywhere within range of your wireless connection.
Wireless setup 1. Position Contour 200i Air in range of your wireless network. 2. Insert the connector of the mains power adapter into the socket on the rear of Contour 200i Air. 18V DC 3. Plug in to the mains supply. 4. A network connection between your computer and Contour 200i Air will then be established automatically. When the red Status LED on the front has stopped flashing, Contour 200i Air is in Standby. 5. Refer to “Connection methods” on page 7 for the next setup steps.
Wired setup 1. Connect an Ethernet cable from the Ethernet port on the back of Contour 200i Air to your router. 2. Insert the connector of the mains power adapter into the DC In socket on the rear of Contour 200i Air. 18V DC 3. Plug in to the mains supply. 4. A network connection between your computer and Contour 200i Air will then be established automatically. When the red Status LED on the front has stopped flashing, Contour 200i Air is in Standby. 5.
Connection methods Contour 200i Air can be connected and used in different ways: • As a docking station for an iPod, iPhone or iPad. See page 19 • As an AirPlay device for playing audio from iTunes on your computer or an iPod touch, iPhone or iPad with AirPlay, via your wireless network. See page 11. • As a speaker for an audio device connected via the Aux In connector. See page 20. Switching between Sleep, Standby and On Contour 200i Air has three power states, Standby, Sleep and On.
Controls and connectors Standby Press to switch between Sleep, Standby and On. See page 7. Press repeatedly to cycle between sources. Mute Volume down Volume up Status LED Fault LED DC In Connector for supplied mains power adapter. 8 Digital Coaxial Connector for output of digital audio signal. See page 20. Wi-Fi Setup Button used when setting up a wireless network. See page 11. Aux In Connector for analogue stereo input for MP3 player or similar. See page 20. Ethernet Connector for network cable.
Remote control Mode: On Hold to enter Standby Press once to exit Standby/Sleep Sleep Hold button to enter Standby Press button once to return to last active state. Standby Press to enter last active state. Source Once in On, press to switch between AirPlay, iPod and Auxiliary input. Shuffle the track playback order. + Vol Menu < Select > and Toggle to repeat current track , repeat all or no repeat. Volume up/Volume down. Press to access the menu on a docked iPod or iPhone.
Front panel Status LED When Contour 200i Air is powered on, the Status LED is visible through the front speaker mesh. This LED indicates the various states of the Contour 200i Air, by colour.
Setting up AirPlay Introduction There are three stages in setting up Contour 200i Air to use AirPlay: 1. Create a connection between Contour 200i Air and your setup device (any device with Wi-Fi and a browser, such as an iPhone or laptop), by using a temporary wireless network. (To connect Contour 200i Air using a network cable see page 6). 2. Add Contour 200i Air to your wireless network using a configuration web page that you can now access on your setup device. 3.
Stage 2: Adding Contour 200i Air to your wireless network Once you have established the temporary connection between your setup device and Contour 200i Air, you can add it to your wireless network as follows: 1. In your setup device’s web browser, enter the following in the address bar: http://192.168.1.12 2. The main configuration web page will display: 3. The Contour 200i Air main configuration page features three tabs. In most cases, you only need to configure the settings on the Connection tab.
Connection tab The wireless settings on the Contour 200i Air can be configured automatically or manually. We recommend trying the automatic configuration first as this should work for the majority of home Wi-Fi networks. Note: We recommend that you contact your IT department before attempting to connect Contour 200i Air to a corporate wireless network. Automatic wireless setup 1. If you prefer, you can change the name of your Contour 200i Air by typing the name (e.g.
Manual wireless setup 1. Select ‘Configure Manually’ from the Network drop-down list and select the encryption type of your wireless network from the drop-down list below. Contour 200i Air supports the following encryption types: • No Encryption Select this option if your wireless network is not being secured with any type of encryption. • WEP Select this option if your wireless network is being secured using the Wired Equivalent Privacy (WEP) method.
Advanced tab The Advanced tab is divided into two main sections, Proxy Server settings and IP address settings. Proxy Server Settings IP Address Settings Configuring Proxy Server settings Carry out the following if the Contour 200i Air will connect to the internet via a proxy server. 1. Tick the Use Proxy Server checkbox. 2. Enter the IP address of your Proxy Server into the Proxy Server box. 3. Enter the port number being used by your Proxy Server into the Proxy Server Port box. 4.
Status tab The Status tab displays a summary of Contour 200i Air’s firmware/hardware information and also displays information about the state of the wireless connection. 16 Connection Status Indicates if Contour 200i Air is connected to a wireless network or not. Also indicates the wireless LAN type, i.e. Basic Service Set, Extended Service Set. Signal Strength Displays the strength of the wireless connection between Contour 200i Air and the peer network device.
Stage 3: Checking your Contour 200i Air is visible Once you have successfully added Contour 200i Air to the same network as your iTunes computer, iPod touch, iPhone or iPad, it should be automatically detected. In iTunes, the AirPlay symbol is located in the bottom status bar of the iTunes window. On an iPod Touch, iPhone or iPad, the AirPlay symbol when playing music. is located at the bottom of the screen The AirPlay symbol will be white when any AirPlay device is available on the network.
Using AirPlay to play audio Using AirPlay AirPlay allows you to stream audio from iTunes to one or more Contour 200i Air devices. AirPlay also allows you to stream audio from an iPod touch, iPhone or iPad to a single Contour 200i Air. Selecting the AirPlay source If you wish to select AirPlay as the source, press Source until the Status LED is white. Note: When an AirPlay connection is established, it will always take control of Contour 200i Air and override any other modes.
Listening to a docked iPod/ iPhone/iPad Compatibility The dock on Contour 200i Air is compatible with most iPod, iPhone and iPad models. For the latest information, check the compatibility table on our website: www.pure.com/products/ipodcompatibility. Docking your device Dock your device onto the connector. Your device will start charging as soon as it is docked and will continue charging whether Contour 200i Air is playing, or in Standby or Sleep.
Using the digital output Using an external digital output device You can connect Contour 200i Air to a digital output device, such as compatible hi-fi system. Any audio playing through Contour 200i Air will also be sent to the attached device. Note: The volume controls on Contour 200i Air will not change the volume on the digital device.
Updating the firmware Firmware updates for your Contour 200i Air will automatically be delivered via the Wi-Fi connection when Contour 200i Air initially boots up. If there is a new version of firmware available, the Status LED will alternately flash red/green/blue/white while the firmware is being installed. A firmware update takes between six to eight minutes.
Help Hints and tips I cannot connect to my wireless network Ensure that your Contour 200i Air is within range of your wireless base station and that you are not located in a dead spot. The Status LED is flashing white Your Contour 200i Air has Airplay selected as the source but does not currently have a connection to a wireless network. Follow the instructions in Setting up AirPlay on page 7. There is a red light on the back of Contour 200i Air This red LED indicates an internal fault.
Specifications Dock compatibility Speakers Audio output Input connectors Output connectors Remote control Mains power supply Dimensions Approvals Supports most iPod, iPhone and iPad* models. For the latest information, check the compatibility table on our website: www.pure.com/products/ipodcompatibility. 2 full-range 3.5” drive units with twin downward firing bass ports. 2 x 18W RMS. 18V DC power adapter socket. iPod/iPhone/iPad dock connector. 3.5mm Aux-in for auxiliary devices. Ethernet socket.
PURE Warranty Statement for Australia This statement replaces any reference to warranty which may be contained elsewhere within this manual What do you need to do now? Option 1: You can register your purchase on-line at https://www.pure.com/au/register/register.asp Option 2: Or you can do nothing other than keep your proof of purchase as evidence of your purchase date. This proof of purchase would need to be presented if warranty service was ever required.
Warranty information Imagination Technologies Ltd. warrants to the end user that this product will be free from defects in materials and workmanship in the course of normal use for a period of two years from the date of purchase. This guarantee covers breakdowns due to manufacturing or design faults; it does not apply in cases such as accidental damage, however caused, wear and tear, negligence, adjustment, modification or repair not authorised by us. Please visit www.pure.
www.pure.com PURE Imagination Technologies Ltd. Home Park Estate Kings Langley Herts, WD4 8LZ United Kingdom http://support.pure.com PURE - Vertrieb über: TELANOR AG Unterhaltungselektronik Bachstrasse 42 4654 Lostorf Suiza info@telanor.ch www.telanor.ch PURE Karl-Marx Strasse 6 64589 Stockstadt/Rhein Alemania sales_gmbh@pure.com http://support.pure.com/de PURE Australasia Pty Ltd PO Box 5049 Wonga Park Victoria 3115 Australia sales.au@pure.com http://support.pure.
