USER'S MANUAL Model No. 831.159700 Serial No. Write the serial number in the space above for reference. Serial Number Decal (under seat) EQUIPMENT [,_i I JR :a_'gl n i_.]i _ m.. 1 HELPLINE! /-800-735-5879 ." _ r_=_:lS I ROEBUCK AND CO. _a_,_)_FMAN ESTATES, IL 60179 S and instructions in this manual before using this equipment, Save this manual for future reference. www.imagefitness.
ImportantPrecautions................................................................... BeforeYouBegin .................................................... Part dentficat_on Chart............ Assembly............................................................................ AdjustingtheWeightBench.............................................................. OrderingReplacement Parts ...................................................... Full90-DayWarranty..................................................
beginning this or any exercise program, consult your physician. This iS especially e of 35or persons with pre-existing health problems.
man .EQr set ,ecmg mevercame IMAGE" e..e. at 1-800-736-6879, MOnday through Saturday, 7 a.m. welgl_tb_nch. The IMAGE" 3.8 is aemgned to help you develop every major muscle group of the body. Whether your goal is a shapely figure, dramatic muscle size and strength, or a healthier cardiovascular system, the'IMAGE" 3.8 will herp you achieve the specific results you want. until 7 p.m. Central Time (excluding holidays).
M6 x 38mm Bolt (60)--1 M6 Washer (30)--5 F_ t_\\\\\\\\\ t_\\\\\\\\\\\\\\\\_ T M6 x 55mm Bolt (4)--4 M6 x 16mm Screw (3)--2 MIO Washer (6)--14 J J J J J J J J J M8 Nylon Locknut M8 Washer (52)--10 (54)--13 MIO Nylon Locknut (11)--24 _\\\\\\\\\ M8 x 70mm Bolt (41)_ M8 x 65mm Carriage Bolt (59)--4 MIO x 25mm Bolt (43)--2 oJ 0,\\\\\\\\\\\\\\\\ • t'n MIO x 65ram Carriage Bolt (40) I o E E 8 o oO _\\\\\\\\\1 X 0 M8 x 60mm Bolt (39)--2 MIO x 65mm Bolt (42)4 _\\\\\\\! M8 x 30mm Bo
• r _" u Before beginning assembly, carefully read the following Information and Instructions: IDENTIFICATION CHART on page 5. • As you assemble the weight bench, make sure all parts are oriented as shown in the drawings. In addition to the included allen wren_ch , assembly requires the following tools (not included): • Two (2) adjustable wrenches • One (1) rubber mallet • Assembly requires two people.
M10 x 65mm Bolts (42), four M10 Washers (6), and two M10 Nylon Locknuts (11). Do not tighten the Nylon Locknuts yet. Slide the Upright (1) and the Brace (2) onto the M10 x 65mm Carriage Bolts (40) and the M8 x 65mm Carriage Bolts (59) in the left Base (7). Attach the Upright with two M10 Nylon Locknuts (11). Attach the Brace with two M8 Washers (52) and two M8 Nylon Locknuts (54). Do not tighten the Nylon Locknuts yet. 59 4O 4, Slide the remaining Brace (2) onto the bracket on the other Upright (1).
While a second person holds a Crossbar (8)in Me position shown, Insert two M10 x 70mm Bolts (46) through the bracket on the Weight Storage Tube (21), the left Brace (2), and the bracket on the Crossbar (8). Thread an M 10 Nylon Locknut (11 ) onto each Bolt. Do not tighten the Nylon Locknuts yet. 46 6, Press a 25mm Round Inner Cap (51) into the end of the other Weight Storage Tube (21).
Insert the Barbell (35) through the locking Bar (34) until the Barbell Is centered in the Locking Bar. 9. Identify the Left Weight Glider (32) by looking at the position of the round tube. 9 Press a 38ram Bushing (29) into each end of the round tube on the Left Weight Glider (32). 32 29 Slide the Left Weight Glider (32) onto the left end of the Barbell (35). Secure the Weight Glider to the Barbell with a hand-tightened M8 x 16mm Screw (50).
Left Safety Spotteris positioned as shown,thehandle. willpoint toward the center of the bench. Place the Left Safety Spotter (24) on the left Base (7) so it is centered over the indicated hole. Have a second person hold the Locking Bar (34) so that the Left Weight Glider (32) rests on top of the Left Safety Spotter (24)..Insert a Weight Guide (18) into the Left Weight Glider, the Left Safety Spotter, and the hole in the Base (7).
A11 Attach the Small Stabilizer (25) to the Bench Frame •.. (5) with two M10 x 65mm Cardage Bolts (40) and two M10 Nylon Locknuts (11). Note: There is an indentation around the holes on one side of the Small "_A _ i//_r I 11- - 5 " " #'-"_.']'!I _'1 iI '4f "--_F_._,<4_> Stabilizer. This side must be facing the floor. _._'_'_"_ 25 40J_J 16. Press a 50mm x 70mm Outer Cap (10) onto each end of the Large Stabilizer (26).
27 and an M10 Nylon Locknut (11). Note: Do not overtighten the Nylon Locknut; the Backrest Tubes must pivot easily. Tube 20. Attach theBackrest (15) to the Backrest Tubes (27) with tour M6 x 55ram Bolts (4) and four M8 Washers (3O). 6 2O 15 : 21. Press a 25ram x 5Ornm inner Cap (58) into the open end of the Seat Support Tube (37). 21 27 9 45 Lubricate an M8 x 80mm Bolt (9).
(37) with two M6 x 16mm Screws (3). Tilt the Seat Support Tube (37) upwards and attach the narrow end of the Seat (14) to the Seat Support Tube with an M6 x 38ram Bolt (60) and an M6 Washer (30). 37 24. Make sure that all parts are properly tightened before you use the weight bench. The use of all remaining parts will be explained in ADJUSTING THE WEIGHT BENCH starting on the following page. .
Th_ _lori explains how the weight bench Is adjusted. See the Included exercise guide for important Information abo_ how to perform a variety of exemlses and how to get the greatest benefit from your exercise program. Inspect and tighten all parts each time you use the weight bench. Replace any wom parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
Toraise the Backrest (15), grip the end of the Backrest with one hand and pull it upwanJ. The Backrest Adjustment Frame (36) will automatically lock into one of the tabs on the bracket on the Bench Frame (5). To lower the Backrest (15), grip the end of the Backrest with one hand and pull it slightly upwards. Grip the handle (not shown) on the right side of the Backrest Adjustment Frame (36) with your other hand and pull the Backrest Adjustment Frame free of the tabs on the bracket on the Bench Frame (5).
KeyNo. Qty.
16 28 8 11 11 2 30 / 21 6 11 42 46 28 57 / 12 11 52 54 11 1(3 20 11 18 17 o o i 11 49 17 : 4o' 7 17 o 49 50 32 10 o o \ 17 48 50 52 40 17 • 29 54 31.
The model number and serial number of your IMAGE 3.8 are listed on a decal attached to the frame. See the front cover of this manual to find the location of the decal. Model No. 831.159700 All replacement parts are available for immediate purchase or special order when you visit your nearest SEARS Service Center. To request service or to order pads by telephone, call the toll-free numbers listed at the left. QUESTIONS? If you find that: • you need help assembling operating the IMAGE 3.
