USB Mini Portable USB Duplicator User’s Guide
CONTENT I. Product Introduction.............................................................................................................................2 1. Overview............................................................................................................................................2 2. Features………………………………………………………………………............................…………..………………………..2 3. Package Contents………………………….………………………………………..........................……...…………….……...2 4.
I. Product Introduction 1. Overview The new compact USB Duplicator will produce up to two mirror image copies of any USB device at lightning fast speed – up to 2GB per minute. The Checking Capability will determine defective devices & the Capacity Checker enables you to determine the actual capacity of a device. The Speed Measuring function will determine a devices actual read & write speed. 2.
. Basic Instructions A. System Overview B. Side Power Switch and Power Supply Input Power Supply Power Switch C.
. Function Table Function Description 1. Copy USB/SD/Micro SD/CF Flash copy. 2. Compare 3. Copy+Compare This option makes bit‐by‐bit comparison between the master source and all other copied flash cards. This option will make a copy first and then compare the copied Flash devices with the source immediately after the copy has finished. 4. Utility 4.1 Device Info. This function will show the Flash device’s general information including capacity, format and data size. 4.
II. Function Introduction 1. Copy The USB Mini Portable USB Duplicator copies data from source Flash devices to target Flash devices. The default setting copy area is “Data Only”. If you would like to change the copy area from “Data Only” to “ Whole HDD” or “All Partitions”, please refer to function [5.1 Copy Area] to select other copy modes. Copy steps: Insert source Flash Device(Master) and target Flash devices into duplicatorÆSelect [1.
ProcessingÆCompare finishedÆ Press[ESC] to finish compare. **Do not remove any Flash device while it is processing. ** When the copying process is in progress, the green LED will flash. When the process has finished the green LED will stop flashing but will remain illuminated. If an error occurs the red LED will illuminate. 3. Copy & Compare This function first makes a copy and then compares the target Flash devices with the source(master) Flash device to ensure data integrity. 4. Utility 4.
viruses. It can only check to see if the virus is present, but cannot clean or eliminate the virus. Show Flash device’s USB virus Steps: 1. Insert Flash devices into duplicatorÆSelect [4. Utility ]ÆPress [OK]ÆSelect [4.2 Chk USB Virus ]ÆPress [OK]ÆSystem will search for USB Viruses When red LED is on, it means the system found a potential risk of a USB Auto run virus. 2. Press [Forward]/[Backward] to check other Flash devices’ for virusesÆ Press [ESC] to finish 4.
1. Insert Flash devices into duplicatorÆSelect [4. Utility ]ÆPress [OK]ÆSelect [4.4 Format FAT]ÆPress [OK]ÆSystem formats the Flash devices 2. Press [Forward]/[Backward] to check other Flash devices’ format statusÆ Press [ESC] to finish. 4.5 Measure Speed This function measures a Flash device’s read and write speed. Check Flash device’s speed Steps: 1. Insert Flash devices into duplicatorÆSelect [4. Utility ]ÆPress [OK]ÆSelect [4.5 Measure Speed]ÆPress [OK]ÆSystem checks the Flash devices speed. 2.
4.8 System Update This function updates the system’s firmware version. Please save an un‐zipped update file to your Flash device (DO NOT save the file in a folder). Insert the Flash device in slot (port #1) and select [8 System Update], press [OK], the system will automatically start to update firmware. When it finished, turn the system off for 5 seconds and then turn it on, the new firmware will be upgraded. 5. Setup 5.1 Copy Area There are two options for copy: Only Data Area and Whole Media.
III. FAQ Q1: Can I use USB Mini to copy other Flash devices such as Micro SD? A1: Some users may use a USB card reader to copy other types of Flash devices, such as SD, CF, and Memory Sticks etc. Due to the different quality and stability of the USB card readers in the market, a poor‐quality card reader may damage the system and the quality of copies. Therefore, it is recommended to copy SD/Micro SD/CF by using a qualified USB card reader.
VI. Specification Model USB Mini Target 2 Operation Standalone Support media USB1.1 / USB2.0 SD / SDHC / Micro SD / MMC / Mini SD / CF (by USB multimedia card reader) Display 2 x 16 Bright LCD Display Control Button 4 Buttons ( Forward , Backward, OK, ESC) LED Green/Red LED on Each Slot Temperature Humidity Working 5°C~45°C Storage ‐20°C~85°C working 20%~80% Storage 5%~95% Power Supply DC +5V, 2A (Adapter) Copy mode Full Copy, Quick Copy Check function Device Info.
