floss VAPE FTE ISH AIRFLOW | FORCEFUL MOTOR | LOW HOSE SPRANG Elements ik www.ikich.com Vising ww Er nail tw i Installation Guide & User Manual Version: 1KIS01 JINRIKISHA KISSOFFS {sand Mount Range Hood 6” Top Vent, 1mm Thickness ITCH STOP and read! Test before installing 1. Please unpack the range hood and accessories carefully, 2. Remove the baffle filters, check any dent or damage inside and outside, 3. If found any loosing parts, please remove them. 4.
PLEASE READ AND SAVE THESE INSTRUCTIONS. WARNING — TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE FOLLOWING CAREFULLY before attempting to assemble, install, operate or maintain the product. CONTENTS 1. KNOW BEFORE INSTALLATION. 2. INCLUDED PARTS & ACCESSORY 3. IMPORTANT SAFETY NOTICE 4. VENTING HEIGHT REQUIREMENTS 85. METHODICALNESS ELECTRICAL REQUIREMENTS & SPECIFICATION INSTALLATION PREPARATION INSTALLATION INSTRUCTIONS. 8. RANGE HOOD OPERATIONS. 10. 1.
Research, plan and prepare the optional accessories & fools. Burt venting and accessories (NOT INCLUDED) st have exhaust duct, prepare « For new insinuation or your old range hood do 10 cut the openings: fireplug the bottom of the cei round duct is included (Recommend ta purchase a higher quality 6” sem aluminum duct if you are noi satisfied with these provided duct) Refer fo Section 3 VENTING METHODS for detail = Check the existing exhaust duet size.
+ The saw ration of greasy residue in the blower and fifers may cause increased inflammability. Keep anti clean and free of grease. and residue tulle-np val times tw prevent possible fires + For optima operation, dean revenged wad all bafflefspacorfilter/groass tunneler container regularly, Regular care will field preserve the appearance of the rage hood. «Filters must be leaned periodically and freak firm accumulation of cooking residue. Old and wom filters must be relapsed immediately. © "DO NOT.
Read sll Instructions before Installing and operating this appearance installation Cautions The installation. in this manual is intended for qualified installers, service technicians or persons with similar qualified background. Installation. and electrical wiring must be done by qu and fn accordance with all applicable cores and standards, including fire fated Constriction.
1 2) Install the bail floes and fin power ON in control panel. Check all lights and fan operations Cones! Panel Layout ami Buttons Configurations: ZEN YARN From left 0 right side: Lighting Key {K1), Timer Key (K2), LED Display, Speed Key (K3), Power Koy (Kd) 3. When the power supply connected. all indicate lighting is On and then Off in [ second “To press K4 10 open the hood 3. Wuhan ihe hou is On. to press Kiosk open Fan Speed 1°.
«BO NOT terminate the vent system in an tic or other looseness © DONG nse 47 (10.2.em] sundry-type Walt caps. «Use bimetallism vent only. Rigid or Flexible meal © allotment vent duct is recommended. + DO NOT ise plastic vent. + Always keep the unclean To ensure proper airflow. © Measure and estimate the following rigors before installation: dares. 1. Districts betting the collateral the range hid. Recommend 23° performance, pint ran 25.57 (inches) for Safety ww 327 for dial concern, 2.
nek fou sy dent or. cng inside nil outside. Idiom any Loosing parts, please remove then Place the tangs aad an a flat bless surface. Don't instill the tempered omit to 2 denigrated standard carol (130-Nikolai, 60712, AC only).
“This range hod is 6” top vent for venting through the roof or wail Vent work cas terminate either through ihe roof.or wall as shows below. “Fo ent through 2 Walt, a 90° obo or a6” semi-rigid akin duct is needed. A imam of 6" round duct (purchase separately) mast be used to rainmaking maxima aid low efficiency. Always use rigid type annihilate nun ducts if available to maximize airflow. Dresden the location of the venting pipe from the hood w the outside.
