- IkeLite Indoor Lighting

9
CCaannoonn,, OOllyymmppuuss && SSoonnyy TTrraayy IInnsseerrtt IInnssttaallllaattiioonn
Applies to Single or Dual Tray.
Non-Ikelite housings are mounted to the tray with a single bolt. To
keep the camera housing from rotating on the tray, a Tray Insert
must be installed. Note that there are 3 Tray Inserts included with
the AF35. Select the Tray Insert for the corresponding camera
housing being installed.
NNOOTTEE::
see special Sony instructions pg.10.
IInnssttaallllaattiioonn
1. The Tray Insert has an adhesive coating on the side opposite the
l
ettering. Remove the protective backing to expose the adhesive.
2. Align the Tray Insert with the Tray Recess, the arrows on the Tray
Insert should be pointing toward the holes in the tray.
3. Place Insert into Recess and push down to secure Insert to tray.
C
ANON
C
ANON
CANON
T
ray Insert
Protective
Backing
Tray Recess
Mounting Holes
Tray Insert
Tray Insert
CANON
OLYMPUS
SONY B
SONY A
Tray Inserts
10
SSoonnyy HHoouussiinngg TTrraayy IInnsseerrtt IInnssttaallllaattiioonn
Applies to Single or Dual Tray.
Sony housings have 2 different size Base Plates. The Tray Insert
marked Sony has 2 different cut-outs. To determine the correct cut-
out, place each of the Sony Tray Insert cut-outs against the Sony
housing Base Plate as shown below. Use the cut-out that fits snug
around the Base Plate. When the correct cut-out is determined
proceed with the installation.
See page 9 for drawings of the following procedure.
1. The Tray Insert has an adhesive coating on the side opposite the
lettering. Remove the protective backing to expose the adhesive.
2. Align the Tray Insert with the Tray Recess, the arrows on the Tray
Insert should be pointing toward the holes in the tray.
3. Place Insert into Recess and push down to secure Insert to tray.
4. See pg. 11 for mounting the Tray to the housing.
SONY B
SONY A
Tripod Mount
Base Plate
Tray Insert
11
MMoouunnttiinngg CCaannoonn,, OOllyymmppuuss && SSoonnyy HHoouussiinnggss ttoo tthhee TTrraayy
Applies to Single or Dual Tray.
After the proper Tray Insert is installed the housing can be mounted
to the AF35 tray. Turn the housing so the Tripod Mount on the
bottom of the housing is facing up. Place the tray across the bottom
of the housing, align the center hole in the tray with the hole in the
Tripod Mount on the bottom of the housing. Insert the mounting
bolt with lock washer as shown below and tighten the bolt firmly to
secure the tray to the housing. Check that the Tripod Mount aligns
correctly with the Tray Insert restricting the housing from rotating
on the tray.
Tripod Mount
Tray Insert
Canon, Olympus
or Sony Housing
Single or Dual Tray
Mounting Blot
Lock Washer
12
IInnssttaalllliinngg HHoouussiinngg DDeefflleeccttoorrss
Installing a Deflector in front of the camera’s built-in flash will block
the camera’s flash from going forward and lighting the particles in
the water; helping to reduce backscatter, it will also deflect the light
back toward the AF35 Sensor used to trigger the AF35 Flash.
IIkkeelliittee HHoouussiinnggss
Deflectors are supplied with Ikelite housings, see housing
instructions for installation.
NNoonn--IIkkeelliittee HHoouussiinngg DDeefflleeccttoorr IInnssttaallllaattiioonn
Most Canon, Olympus and Sony digital camera housings have a flash
diffuser built on the housing to which the deflector can be attached.
(see drawing pg 13). If the housing does not have a flash diffuser
pick a spot on the outside of the housing in front of the camera’s
built-in flash to mount the deflector.
Deflector Kit includes:
1 strip of hook material, 1/4” wide x 6” long
1 strip of loop material, 2” wide x 3” long
1. The loop material (deflector) is white on one side and black on the
other side. The white side will go against the housing as it has loops
that will stick to the hook material once it is secured to the housing.
2. Using a piece of paper, cut a template to fit on the outside of the
housing in front of the camera’s built-in flash. Trace the template
on the loop material and cut it out. Test fit the loop material
(deflector) on the housing and trim as necessary.
3. Position the loop material (deflector) on the housing to determine
where to locate the 2 strips of hook material to secure the deflector
to the housing. Cut 2 strips of the hook material to fit on each side
or on the top and bottom of the deflector. Peel the adhesive
backing from the hook material strips and press them onto the
housing. The loop material (deflector) can now be secured or easily
removed from the housing.