Manual

5
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting
installation. Read and follow the instructions provided
with any tools listed here.
Tools Needed
■ Level
■ Drill with 1
1
/
4
" (3.0 cm),
3
/
8
" (9.5 mm),
1
/
8
" (4.8 mm),
and
7
/
64
" (2.75 mm) drill bits
■ Pencil
■ Wire stripper or utility knife
■ Tape measure or ruler
■ Pliers
■ Caulking gun and weatherproof caulking compound
■ Vent clamps
■ Jigsaw or keyhole saw
■ Flat-blade screwdriver
■ Metal snips
■ Phillips screwdriver
■ Metric hex key set
Parts Needed
■ Home power supply cable
■
1
/
2
" (12.7 mm) UL listed or CSA approved strain relief
■ 3 UL listed wire connectors
For Vented Installations, You Will Also Need:
■ 1 wall or roof cap
■ Metal vent system
For Non-Vented (Recirculating) Installations,
You Will Also Need:
■ Charcoal Filter Kit Part Number W10412939 for non-vented
(recirculating) installations only. See the “Assistance or
Service” section to order.
■ 6" (15.2 cm) diameter round metal vent duct—
length required is determined by ceiling height.
Parts Supplied
Remove parts from packages. Check that all parts are included.
■ Hood canopy assembly with ventilator and LED lights
installed
■ Vent transition with back draft dampers installed
■ Metal grease filter(s)
■ Vent cover support bracket
■ Mounting template
■ Air deflector with extensions (for non-vented installations)
■ 2-piece vent cover
■ 2 - 2.9 x 6.5 mm screws (T10 drive)
■ 6 - 3.5 x 6.5 mm screws (T10 drive )
■ 2 - 3.5 x 9.5 mm screws (Phillips)
■ 4 - 4.2 x 8 mm screw (T20
®†
drive)
■ 6 - 5 x 45 mm mounting screws (#2 Phillips drive)
■ 6 - 8 x 40 mm wall anchors (masonry)
■ 2 - Flat washers
■ T10 Torx
®†
adapter
■ T20
®
Torx
®
adapter
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer’s responsibility to comply with installation clearances
specified on the model/serial/rating plate. The model/serial/
rating plate is located behind the left filter on the rear wall
of the vent hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
This range hood is recommended for use with cooktops
with a maximum total rating of 60,000 BTUs or less.
Grounded electrical outlet is required. See “Electrical
Requirements” section.
The canopy hood is factory set for venting through the roof or wall.
For non-vented (recirculating) Installation, see “For
Non-vented (recirculating) Installation Only” in “Connect Vent
System” section. Charcoal Filter Kit Part Number W10412939
is available from your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will
be installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title
24 CFR, Part 328 (formerly the Federal Standard for Mobile
Home Construction and Safety, Title 24, HUD, Part 280)
or when such standard is not applicable, the standard for
Manufactured Home Installation 1982 (Manufactured Home
Sites, Communities and Setups) ANSI A225.1/NFPA 501A
or latest edition, or with local codes.
Product Dimensions
9
3
/8"
(238 mm)
18
7
/8"
(480 mm)
11
3
/4"
(298 mm)
*32
1
/8" (816 mm) min.
**31
3
/8" (797 mm) min.
*45
1
/8" (1146 mm) max.
**41" (1041 mm) max.
2"
(51 mm)
4"
(356 mm)
30"
(762 mm)
10
7
/8"
(276 mm)
* For non-vented (recirculating) installations only
** For vented installations only
†
®
TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.