20000003967 EUROSTAR_102014 IKA® EUROSTAR 20 high speed control Operating instructions EN
EUROSTAR station Wireless Controller (WiCo) D E F 3 2 Q C 4 1 G N O B P L M H I J P Fig. 2 A G J H N O P G I Fig. 1 RS 232 Fig. 3 R Fig. 4 Temp. Sensor T U U S Q Fig. 5 USB Fig. 6 H G Z G I X W V Fig. 7 Fig.
EN Source language: German Contents Page Page EC-Declaration of conformity 3 Note for USA (FCC) 3 Note for Canada (IC) 3 Explication of warning symbols 3 Safety instructions 4 Correct use 5 Unpacking 5 Drive 6 Motor protection 6 Speed – normal operation 6 Speed – overload operation 6 Output shaft 6 Speed display 6 Commissioning 6 Securing 7 Switching on the instrument 8 Useful information 8 Wireless Controller (WiCo) 8 Interfaces and outputs 14 Maintenance and cleaning 16 Error codes
Safety instructions • Read the operating instructions in full before starting up and follow the safety instructions. • Keep the operating instructions in a place where it can be accessed by everyone. • Ensure that only trained staff work with the instrument. • Follow the safety instructions, guidelines, occupational health and safety and accident prevention regulations.
• The machine must only be opened by trained specialists, even during repair. The instrument must be unplugged from the power supply before opening. Live parts inside the instrument may still be live for some time after unplugging from the power supply. Covering or parts that are capable of being removed from the unit without accessory equipment have to be reattached to the unit for safe operation in order to prevent, for example, the ingress of fluids, foreign matter, etc..
OS 1.0 power supply unit (for Wireless Controller (WiCo)) Adapter Europe, Switzerland Adapter USA, China Adapter Australia Adapter England Drive The rotary knob (B, see Fig. 1) of the Wireless Controller (WiCo) allows the speed of the stirrer to be adjusted over the entire speed range. Motor protection The stirring instrument is suitable for continuous operation. The motor current is limited electronically. The instrument has an anti-stall and anti-overload system.
Securing Securing the extension arm to the overhead stirrer Diagram (see Fig. 2) Ensure that the extension arm is fitted securely. Vibration may cause the screw to become loose. It is therefore necessary for safe use to occasionally check that the extension arm is attached securely. Tighten the hexagonal socket screw as required. Securing the overhead stirrer to the stand Diagram (see Fig. 3) First secure the cross sleeve (H) to the stand (I).
Switching on the instrument Check whether the voltage given on the type plate corresponds to the available mains voltage. The socket used must be earthed (fitted with earth contact). If these conditions have been met, the machine is ready for operation when the mains plug is plugged in. If these conditions are not met, safe operation is not guaranteed and the machine could be damaged.
Working screen at the time of delivery: B 0 Torque: Reset Torque Timer: Ncm Back 00:00:00 0 actual rpm 0 set rpm The start screen appears for a few seconds after the Wireless Controller is switched on. The device name and the software version are displayed. After this, the following working screen appears automatically in the display. Note: The wireless symbol appears only when the stirrer (station) is switched on. Explanation of symbols on the working screen: B Torque: Temp.
Menu structure Factory settings Menu Stirring Speed Limit ………………………………………………………………………… 6000 rpm Torque Limit ……………………………………………………………..………… 20 Ncm Torque Display ……………………………………………………………………… activated Intermittent Mode Run/Stop …………………………………........ Interval Run Time…..…………... 00:00 [mm:ss] Stop Time………………. 00:00 [mm:ss] Torque Calibration…………………………………………………………............. - Temperature Probe Temperature……………………………………………………………… Display……………………………………………………………………………..
Menu (details) Stirring Speed Limit: The ”Speed Limit” menu allows the user to set the desired maximum upper speed limit for the EUROSTAR 20 high speed control stirrer. The initial setting is the maximum permissible speed of the stirrer. If the user changes this setting, the Wireless Controller saves the new value for future stirring tasks. If the “Speed Limit” has been changed, then the speed can be adjusted only within the new range.
Operating Mode Operating Mode A: In this operating mode, the set speed is not saved when the current run comes to an end or the device is switched off. Operating Mode B: In this operating mode, the set speed is saved when the current run comes to an end or the device is switched off, and the value can be changed. Operating mode C: In this operating mode, the set speed is saved when the current run comes to an end or the device is switched off, and the value cannot be changed.
Sample for editing the program: PROGRAM 1 Programs Programs Programs Program 1 Program 1 Program 1 Program 2 Program 2 Program 2 Program 3 Program 3 Program 3 Program 4 Program 4 Program 5 Program 5 PROGRAM 1 Seg No. rpm Time hh:mm 1 0 00:00 Interm. Mode No Edit Delete PROGRAM 1 Seg No. rpm 0 1 Edit Start edit PROGRAM 1 Time Interm. hh:mm Mode Seg No. 00:00 1 No rpm 0 3 4 4 Edit edit PROGRAM 1 Seg No. 00:00 1 rpm 150 Delete No rpm Time Interm.
Safety Time Out: In the “Time Out“ menu, the user can set a time limit. This time limit applies if there is a communication failure between the EUROSTAR station and the Wireless Controller or the communication range is exceeded. The EUROSTAR station will continue to run at the set speed until the set time has expired. After that the EUROSTAR stirrer (station) will continue to run at the set safe speed (see the "Safe speed" menu). Note: The initial setting for the time limit is 30 seconds.
- Each individual command (incl. parameters and data) and each response are terminated with Blank CR LF (Code: hex 0x20 hex 0x0d hex 0x20 hex 0x0A) and have a maximum length of 80 characters. - The decimal separator in a number is a dot (Code: hex 0x2E).
9-pin RS 232 9-pin RS 232 or A micro B USB A USB micro B USB A Maintenance and cleaning The instrument is maintenance-free. It is only subject to the natural wear and tear of components and their statistical failure rate. Cleaning For cleaning disconnect the main plug! Use only cleaning agents which have been approved by IKA® to clean IKA® instruments.
Warranty In accordance with IKA® warranty conditions, the warranty period is 24 months. For claims under the warranty please contact your local dealer. You may also send the machine direct to our factory, enclosing the delivery invoice and giving reasons for the claim. You will be liable for freight costs.
Technical data EUROSTAR station + Wireless Controller (WiCo) Speed range under nominal load Speed adjustment Speed display Speed setting accuracy Deviation – speed measurement rpm rpm Max. torque at stirrer shaft Torque trend measurement Torque trend display Deviation – torque measurement Max. stirring quantity (water) Max. viscosity Intermittent operation Reversible direction of rotation Port for ext.
IKA® - Werke GmbH & Co.KG Janke & Kunkel-Str. 10 D-79219 Staufen Tel. +49 7633 831-0 Fax +49 7633 831-98 sales@ika.de www.ika.
