User's Manual
Table Of Contents
- Contents
- Introduction
- 1 – Installation and Setup
- 2 – Turning The Unit On/Off - Calibration Process
- 3 – Overview
- 4 – Front Panel Interface
- 4.1 – Home Display
- 4.2 – Sound Editing Matrix
- 4.2.1 – Oscillators (OSC)
- 4.2.2 - Mixer (MIX)
- 4.2.3 – Filters (FILTER)
- 4.1.4 – LFOs (LFO)
- 4.2.5 – Envelopes (FILTER ENV - AMP ENV)
- 4.2.6 – Modulation Matrix (MATRIX)
- 4.2.6 – Effects (FX)
- 4.2.7 – Effects Type List And Parameters
- 4.2.8 – Other Sound Editing Shortcuts
- 5 – Global Controls
- 5.1 – Presets
- 5.1.1 – The Edit Preset Menu
- 5.1.2 - Store a Preset
- 5.1.3 – Recall Preset
- 5.1.4 – Rename Preset
- 5.1.5 – Initialize A Preset
- 5.1.6 – Compare Preset
- 5.1.7 – Demo
- 5.2 – Setup
- 5.2.1 – Master Tuning
- 5.2.2 – MIDI
- 5.2.3 – Sync
- 5.2.4 – Keyboard
- 5.3 – Song
- 5.4 – Arpeggiator
- 5.5 – Sequencer
- 5.5.1 – ALT(ernative) Editing button
- 5.6 – Voice Mode: Assign System
- 6 – FAQ and Troubleshooting
- 7 – Support
UNO Synth Pro
4 – Front Panel Interface
22
4.2.7 – Effects Type List And Parameters
The controls for the effects are:
DELAY:
TYPE: Selects between MONO, STEREO, DOUBLER, PING PONG and LCR.
SYNC: Enables or disables the sync of the delay division to the master tempo.
TIME (both L and R when available): Adjusts the delay tempo and division. When sync is off, the tempo goes
from 1ms to 350ms without decimal values. When sync is on, the values are 1/4, 1/8 T, 1/8 D, 1/8, 1/16 T, 1/16
D, 1/16, 1/32T, 1/32 D, 1/32 (some divisions depend on the master tempo).
NOTE: The maximum total delay time is 1 second, which becomes 500ms for stereo delays and 350 for LCR.
For this reason, available time divisions depend on the delay type and BPM.
FEEDBACK: Adjusts the delay feedback from 0% to 80% (where 100% is near auto oscillation).
FILTER: Adjusts the LPF cutoff from 20Hz to 10000Hz.
REVERB:
TYPE: Selects between HALL, PLATE, REVERSE and SPRING.
PRE-DELAY: Adjusts the pre-delay time between 0ms and 200ms.
SIZE: Adjusts the reverb size between 0 and 100.
TIME: Adjusts the reverb decay time. Each type has a different way to deal with the decay:
• HALL PLATE: will have 3 controls: TIME with min 0.1 and max 30 sec, TIME LOW and TIME HIGH (with
the same range). Changing TIME will automatically change the other 2 settings. If you changed manually
TIME LOW or HIGH, the control TIME will automatically retain the ratio between the controls.
• REVERSE: Time is a feedback control that goes from 0% to 100%
• SPRING: Time goes from 0.2 to 15 sec.
FILTER: Adjusts the LPF IN from 50Hz to 10kHz.
MODULATIONS:
TYPE: Selects between CHORUS, PHASER and FLANGER
MODE: Available only for CHORUS. Select between SYNTH I, SYNTH II and STRING.
INTENSITY/DEPTH: Available only for CHORUS. Adjusts the intensity of the effect between 0% and 100%.
RATE: Adjusts the speed of the effect
COLOR: Available only for PHASER. Select between COLOR 1 and 2.
FEEDBACK: Available only for FLANGER. Adjust the amount of feedback in a range of +/-100%