USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
ENGLISH
CE MARKING DECLARATION OF CONFORMITY IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands Model No. : PL2738M We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address: http://www.iiyama.com You can access the Web page of different countries from there. We reserve the right to change specifications without notice.
TABLE OF CONTENTS FOR YOUR SAFETY.............................................................................1 SAFETY PRECAUTIONS................................................................1 SPECIAL NOTES ON LCD MONITORS..........................................3 ENGLISH CUSTOMER SERVICE....................................................................3 CLEANING.......................................................................................3 BEFORE YOU OPERATE THE MONITOR....................
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. ENGLISH DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
SPECIAL NOTES ON LCD MONITORS NOTE When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours.
BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1920 × 1080 2 2 High Contrast 1000:1 (Typical) / Brightness 500cd/m (Typical), 425cd/m (with Touch panel) ENGLISH Digital Character Smoothing Automatic Set-up Stereo Speakers 2 × 3W Stereo Speakers Standby Feature (VESA DPMS Compliant) VESA Mounting Standard (200mm×100mm, 100mm×100mm) Compliant IPX1 Standard Compliant (Only front face) CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your pack
INSTALLATION WARNING Before installation, make sure the wall, ceiling or desktop arm is strong enough to hold the necessary weight of the display and the mount. < WALL MOUNTING > WARNING When you use with the wall mounting, in consideration of thickness of the mounting stage, tighten the M4 Screws (4 pcs) with washer which “L” length is 8mm(VESA screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor.
CONTROLS AND CONNECTORS MENU ENGLISH ENTER Menu Button (MENU) Scroll Up / Audio Adjust Button ( ) Scroll Down / i-Style Color Button ( ) Select / Input Select Button (ENTER) Power Switch ( ) Speakers Power Indicator NOTE Blue: Orange: Standby mode Normal operation USB Connector (USB) Audio Connector (AUDIO IN) HDMI Connector (HDMI) DVI-D Connector (DVI) DisplayPort Connector (DP) AC Connector( : Alternating current) (AC POWER IN) 6 BEFORE YOU OPERATE THE MO
CONNECTING YOUR MONITOR Ensure that both the computer and the monitor are switched off. Connect the computer to the monitor with the signal cable. Connect the computer to the monitor with the USB Cable. NOTE Make sure that the building installation has a circuit breaker of 120/240V, 20A (maximum). The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer.
[Fitting and Removal of Cable Cover] Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down. ENGLISH < Fitting > Remove the screw from the monitor as shown in Step1. Step 1 Connect the cables, as shown in Step2, place the cable cover and fix it firmly using a screw. Screw Step 2 Cable Cover Screw < Removal > Remove the screw and the cable cover as shown in Step3.
COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 22: COMPLIANT TIMING. TOUCH support operation system Mouse Digitizer Gestures *1 Remarks Mac OS/OS X *2 *3 Linux Android *4 Functions Click Drag Double-Click Mouse function Right-Click Flick Visual feedback For Mac OS X version 10.6 and above you need a driver. Works for single touch only. Kernel 2.6.38 and above Kernel 2.6.
Touch Input Settings in Dual Screen Mode ENGLISH Connect the primary monitor to the computer first. Set Control Panel > Hardware and Sound > Tablet PC Settings > Display > Setup. The following message will appear on the screen. Please follow the instructions. After setting NOTE , connect a second monitor and perform the setup as in . The monitors are recognized as dual-display, and touch operation cannot be performed on two monitors at the same time.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 22. You are also able to adjust the picture by following the button operation shown below. Press the Button to start the On Screen Display (OSD) feature. There are additional Menu items which can be switched by using the / Buttons.
ADJUSTMENT MENU CONTENTS Picture Adjust Picture Adjust ENGLISH Adjustment Item Problem / Option Contrast *3 Too dull Too intense Brightness *1,2,3 Too dark Too bright Adv. Contrast *2,3,4 ECO Mode *3 Overdrive *5 Off Typical Contrast Ratio On Increased Contrast Ratio Off Normal Button to Press 1 Brightness of back-light is reduced. 2 Brightness of back-light is reduced more than 1. 3 Brightness of back-light is reduced more than 2.
Direct Adjustment Item Problem / Option Button to Press DVI Select the DVI input. HDMI Select the HDMI input. DisplayPort Select the DisplayPort input. Search for an available input source and select Auto automatically. Input Select NOTE Input Select Input source is fixed, not selected automatically when DVI, HDMI and DisplayPort which are selected. Direct You can skip the Menu items and directly display an option setting screen by using the following button operations.
Color Adjust * Color Adjust Adjustment Item Problem / Option Cool Bluish white Normal Greenish white Reddish white User Color Red Green Blue ENGLISH Warm Off Standard Direct i-Style Color Button to Press Too weak Too strong Return to a state set by color adjustment except i-Style Color. For general windows environment and monitor default setting. Game For PC game environment. Cinema For movie and video environment.
Manual Image Adjust Adjustment Item Manual Image Adjust Problem / Option Button to Press Sharpness Video Mode Adjust Blue Light Reducer *2 Direct X-res Technology You can change the picture quality from 1 to 5 (soft to sharp). Button to change the picture quality in numerical Press the order. Press the Button to change the picture quality in reverse numerical order. Adjust the picture quality at resolutions of less 1920 x 1080. You can change the picture quality (5 steps).
Setup Menu Adjustment Item ENGLISH Language Select Setup Menu Problem / Option English Français Deutsch Nederlands Polski English French German Dutch Polish OSD H.Position OSD is too left OSD is too right OSD V.Position OSD is too low OSD is too high Button to Press Русский Russian Japanese Simplified Chinese Traditional Chinese OSD Position OSD Time Out OSD Background* Opening Logo* LED* NOTE You can set the OSD display duration time.
● Lock Mode 1. The OSD lock will be activated by pressing the front buttons and for about 5 seconds. If you try to access the OSD by pressing any of the buttons , , and , message "OSD Locked" will appear on the screen. and again for 5 seconds. 2. The OSD lock will be deactivated by pressing the front buttons 1. The power switch lock will be activated by pressing the front buttons and for 5 seconds.
STANDBY FEATURE ENGLISH The standby feature of this product complies with power saving requirement of VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a standby step the monitor takes as described below. The standby function, including any timer settings is configured by the operating system.
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. 3.
Problem Check A strange noise is heard. The Audio Cable is properly connected. T h e t o u c h screen shows no response. The USB Cable is firmly seated in the socket. Touch screen driver software is installed. The calibration function set up correctly. ENGLISH The touch position does not deviate. RECYCLING INFORMATION For better environment protection please don't dispose your monitor. Please visit our web site: www.iiyama.com for monitor recycling.
APPENDIX Design and specifications are subject to change without prior notice. Touch Screen Technology Projected capacitive 10pt touch Light transmission 85% Hardness 6H Total thickness 3.6mm Communication system USB serial transfer Size Category LCD Panel ENGLISH SPECIFICATIONS : ProLite TF2738MSC-B2 27" Panel technology IPS (In-Plane-Switching) Size Diagonal: 27" (68.6cm) Pixel pitch 0.3114mm H × 0.
DIMENSIONS 20.3mm/0.8” 52.0mm/2.0” 318.0mm/12.5” 10xM4 SCREW HOLE (VESA MOUNT) 224.25mm/8.8” 142.5mm/5.6” 48.5mm/1.9” 50.0mm/2.0” 216.0mm/8.5” 338.0mm/13.3” 386.5mm/15.2” 193.0mm/7.6” 68.0mm/2.7” 250.0mm/9.8” 68.5mm/2.7” 50.0mm/2.0” 50.0mm 50.0mm 8xM4 SCREW HOLE (Outer) 11.0mm/0.4” ENGLISH 52.0mm/2.0” 100.0mm/3.9” 648.5mm/25.5” 599.5mm/23.6” 11.0mm/0.4” 174.25mm/6.9” 300.0mm/11.8” 174.25mm/6.
