USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.
CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC Directive”, 2014/35/EU “Low Voltage Directive” and 2011/65/EU “RoHS Directive”. Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. IIYAMA CORPORATION: Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands ENGLISH Model No.
TABLE OF CONTENTS FOR YOUR SAFETY............................................................................1 SAFETY PRECAUTIONS................................................................1 SPECIAL NOTES ON LCD MONITORS .........................................3 CLEANING ......................................................................................5 BEFORE YOU OPERATE THE MONITOR ..........................................6 FEATURES................................................................
FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fire or electric shock. NEVER REMOVE THE CABINET High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor. ENGLISH DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located.
SPECIAL NOTES ON LCD MONITORS NOTE - When you first turn on the LCD monitor, the picture may not fit in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position. - You may find slightly uneven brightness on the screen depending on the desktop pattern you use. - Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours.
USAGE CONFIRMATION This product is designed for optimum usage at 24hours per day. The display is compatible for usage in Landscape/Portrait and Tabletop (face-up) applications. If being used in Tabletop application, please utilise the Fan-on function. IMAGE PERSISTENCE / IMAGE STICKING ENGLISH Please be aware that all LCD screens can experience Image Persistence or Image Sticking. This occurs when a residual image remains visible on a screen when static images are displayed for long periods of time.
CUSTOMER SERVICE NOTE If you have to return your unit for service and the original packaging has been discarded, please contact your dealer or iiyama service center for advice or replacement packaging. If you drop any materials or liquids such as water into the monitor when cleaning, WARNING unplug the power cable immediately and contact your dealer or iiyama service center. For safety reasons, turn off the power switch and unplug the monitor before you CAUTION clean it.
BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1920 × 1080 2 High Contrast 3000:1 (Typical) / Brightness 500cd/m (Typical: without Touch panel): ProLite TF3237MSC ENGLISH 2 High Contrast 1000:1 (Typical) / Brightness 400cd/m (Typical: without Touch panel): ProLite TF4237MSC-B2AG 2 High Contrast 3000:1 (Typical) / Brightness 400cd/m (Typical: without Touch panel): ProLite TF4237MSC-B3AG 2 High Contrast 4000:1 (Typical) / Brightness 500cd/m (Typical: without Touch panel): ProLi
UNPACKING : ProLite TF4237MSC Before unpacking your monitor, prepare a stable, level, and clean surface near a wall outlet. Set the LCD Monitor box in an upright position and open from the top of the box before removing the top cushions. Remove the carton holders. Pinch and Pull the Knob. CAUTION Moving the monitor requires at least two people. If not, it may drop and could result in a serious injury. When moving/shipping the monitor, please hold by the carton holders.
CONTROLS AND CONNECTORS : MONITOR POWER UP DOWN AUTO/EXIT POWER ENGLISH UP DOWN SOURCE/OK AUTO/EXIT SOURCE/OK MENU MENU LED IR AC IN USB COM IN HDMI DVI IN VGA IN AUDIO IR IN LED IR POWER Power Button UP Up/Volume + Button DOWN Down/Volume - Button AUTO / EXIT Auto/Exit Button SOURCE / OK Input Select/OK Button MENU Menu Button LED Green Normal Operation Orange Power Management IR Remote Sensor SPEAKERS Speakers AC IN AC-INLET AC Connector( AC
INSTALLATION CAUTION ENGLISH Follow the manual instructions for the type of mount you have selected. Refer all servicing to qualified service personnel. Moving the monitor requires at least two people. Before installing, please make sure the wall is strong enough to hold the necessary weight of the display and the mount. [WALL MOUNTING] Mounting Stage Screw L Chassis CAUTION When using the wall mounting, consideration of thickness of the mounting stage needs to be taken.
[ROTATING THE DISPLAY] It is designed to be compatible in both landscape and portrait modes, however, it is optimized for landscape mode.
CONTROLS AND CONNECTORS : REMOTE CONTROL (For maintenance) POWER MUTE MEMU AUTO OK ENGLISH PLAY VOL EXIT STOP SELECT NOTE To use the remote control we advise you to position it at the back of the monitor (left side) where the remote sensor is located. It might not work if you use it standing in front of the monitor. POWER Turns the monitor ON and OFF. MENU Opens the monitor’s on-screen menu systems. When the menu system is already open, pressing this button will select the previous submenu.
PREPARING THE REMOTE CONTROL To use the remote control, insert the button battery. CAUTION Do not use any other batteries other than those specified in this manual for the Remote Control. Burst batteries or the electrolyte from these batteries may cause stains, fire or injury. ENGLISH Push Lock to right and remove the battery case in the direction of the arrow. Put it in face up the + side of the button battery (CR2025). Button Battery Replace the battery case in the direction of the arrow.
BASIC OPERATION Turning the monitor ON The monitor is on and the Power Indicator turns Green when you press the Power Button on the monitor or the Remote Control. The monitor is off and the Power Indicator turns Orange when you press the Power Button on the monitor or the Remote Control. Press again to turn the monitor on.
Move the cursor vertically Select adjustment by pressing the UP / DOWN Button on the monitor or the Remote Control while the menu page is displayed on the screen. [Monitor] POWER / Button on the [Remote Control] POWER MUTE UP MEMU ENGLISH AUTO/EXIT AUTO OK DOWN PLAY VOL EXIT STOP SOURCE/OK SELECT MENU LED IR Move the cursor horizontally Select menu or setting, or perform the adjustment by pressing the Control while the menu page is displayed on the screen.
Adjust the volume of sound Press the UP / DOWN Button on the Monitor or the VOL / Button on the Remote Control to adjust the volume of sound when the menu page is not displayed on the screen. [Monitor] [Remote Control] POWER MUTE POWER UP MEMU AUTO OK DOWN PLAY EXIT ENGLISH VOL AUTO/EXIT STOP SELECT SOURCE/OK MENU LED IR Switch the input signal This is activated when you successively press the SOURCE Button on the monitor or SELECT Button on the Remote Control.
CONNECTING YOUR MONITOR ENGLISH Ensure that both the computer and the monitor are switched off. Connect the computer to the monitor with the signal cable. Connect the computer to the monitor with the USB Cable. Connect the Power Cable to the monitor first and then to the power supply. Turn on your monitor (Main Power Switch and Power Switch) and computer. NOTE The signal cables used for connecting the computer and monitor may vary with the type of computer used.
COMPUTER SETTING Windows XP/Vista/7/8/8.1/10 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows XP/Vista/7/8/8.1/10 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied. For installation on Windows XP: The monitor Information File for iiyama monitors may be necessary for your computer and obtained via the Internet, using the address: http://www.iiyama.
OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 36. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 25 for SCREEN ADJUSTMENTS. ENGLISH Press the MENU Button to start the On Screen Display feature. There are additional / Buttons.
LOCK MODE: * Available for Back Controller only. Pressing and holding the MENU button and the Power Switch for about 3 seconds when the Menu is not displayed. * The OSD menu is not displayed when the OSD is locked. Pressing and holding the MENU button and the Power Switch for about 3 seconds when the Menu is not displayed. The following OSD menu is displayed. OSD Power Key Remoto Control Problem / Option On The OSD menu is Locked. Off The OSD menu is Unlocked. On The POWER SWITCH is Locked.
ADJUSTMENT MENU CONTENTS Brightness/Contrast ENGLISH Schedule Settings Adjustment Item Problem / Option Brightness * Too dark Too bright Contrast Too dull Too intense Button to Press * Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright. Color Settings Schedule Settings Adjustment Item Color Temp.
Display Settings Schedule Settings Problem / Option Off Aspect Ratio Button to Press Aspect Ratio is turned off. 16:10 Displays all picture in 16:10 aspect ratio. 5:4 Displays all picture in 5:4 aspect ratio. 4:3 Displays all picture in 4:3 aspect ratio. Gamma You can set the Gamma. Native / 2.2 / 1.8 Sharpness You can change the picture quality from 0 to 100 (soft to sharp). Press the Button to change the picture quality in Button to change the numerical order.
Other Settings Schedule Settings ENGLISH Adjustment Item Problem / Option Language English Français Español Deutsch OSD time out You can set the OSD display duration time between 5 and 30 seconds. Volume Too soft Too loud Mute Fan *1 Anti Image Retention Opening Logo Factory Reset *2 English French Spanish German Button to Press Nederlands Poliski Pусский Italiano Dutch Polish Russian Italian On Turn off the sound temporarily. Off Return the sound volume to the previous level.
Schedule Settings Date and Time 2016 - 03 - 11 Timer day set Everyday On timer input select VGA 15 : 00 Reset Schedule Settings Date and Time Timer day set * Problem / Option Adjust the current date and time for the internal clock. Date / Time Sets a recurring schedule. Everyday / Sun / Mon / Tue / Wed / Thu / Fri / Sat Activation On Time Off Time On timer input select Reset Button to Press On Schedule is turned on. Off Schedule is turned off.
Input Source Schedule Settings ENGLISH Adjustment Item Input Source Problem / Option Button to Press AUTO Select the signal input automatically. VGA Select the analog input. DVI HDMI Select the digital(DVI) input. Select the digital(HDMI) input. NOTE When only one of the three signal inputs is connected to the signal source, the one connected is automatically selected.
SCREEN ADJUSTMENTS The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use. The monitor is designed to provide the best performance at resolution of 1920 × 1080, but can not provide the best at resolutions of less than 1920 × 1080 because the picture is automatically stretched to fit the full screen. It is recommended to operate at resolution of 1920 × 1080 in normal use.
Adjust the Auto Adjustment. Adjust the image manually by following procedure below when the screen has a flicker or blur, or the picture does not fit in the display area after performing the Auto Adjust. ENGLISH Adjust the V-Position so that the top and bottom of the picture frame will fit to the display area. 1) Adjust the H-Position so that the left side of the picture frame will move to the left edge of the display area.
NOTE and In case the strong flicker or blurs remain on a part of the screen, repeat steps because the Clock may not be adjusted correctly. If the flicker or blurs still remain, set again. the refresh rate of computer to low (60Hz) and repeat steps from Adjust the H-Position after the Phase adjustment if the horizontal position moves during the adjustment. Adjust the Brightness and Color to get the desired picture after you complete the Clock and Phase adjustments. Put back your favorite wallpaper.
POWER MANAGEMENT FEATURE ENGLISH The power management feature of this product complies with power saving requirement of VESA DPMS. When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured by the operating system.
TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. 1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2. 2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. 3.
RECYCLING INFORMATION ENGLISH For better environment protection please don't dispose your monitor. Please visit our web site: www.iiyama.com/recycle for monitor recycling.
APPENDIX Design and specifications are subject to change without prior notice. SPECIFICATIONS : ProLite TF3237MSC Touch Screen 84% Hardness 7H Thickness 4mm Communication system Size Category LCD Panel Projected Capacitive 12points USB serial transfer ENGLISH Technology Light transmission 32" Panel technology MVA Size Diagonal: 31.5" (80cm) Pixel pitch Contrast ratio 0.364mm H × 0.
SPECIFICATIONS : ProLite TF4237MSC Model Name Technology Touch Screen Light transmission 84% Hardness 7H Thickness 4mm Communication system ENGLISH Size Category LCD Panel ProLite TF4237MSC-B2AG ProLite TF4237MSC-B3AG Projected Capacitive 12points USB serial transfer 42" Panel technology IPS Size Diagonal: 42" (106.5cm) Pixel pitch Contrast ratio 0.4833mm H × 0.4833mm V 0.4845mm H × 0.
Model Name ProLite TF4237MSC-B4AG Technology Light transmission 84% Hardness 7H Thickness 4mm Communication system Size Category LCD Panel USB serial transfer 42" ENGLISH Touch Screen Projected Capacitive 12points Panel technology AMVA3 Size Diagonal: 42" (106.5cm) Pixel pitch Contrast ratio 0.4845mm H × 0.
DIMENSIONS : ProLite TF3237MSC 35.5mm/1.4” 69.0mm/2.7” 620.0mm/24.4” 781.5mm/30.8” 700.5mm/27.6” 103.5mm/4.1” 355.0mm/14.0” 200.0mm/7.9” 395.0mm/15.6” 476.0mm/18.7” 138.0mm/5.4” 200.0mm/7.9” 400.0mm/15.7” 138.0mm/5.4” ENGLISH 4xM6 SCREW HOLE (VESA MOUNT) 238.0mm/9.4” 20.0mm/0.8” 8xM6 SCREW HOLE (Outer) 400.0mm/15.7” 190.75mm/7.55” 20.0mm/0.8” 190.75mm/7.55” DIMENSIONS : ProLite TF4237MSC-B2AG 63.0mm/2.5” 88.0mm/3.5” 591.5mm/23.3” 975.5mm/38.4” 928.0mm/36.
DIMENSIONS : ProLite TF4237MSC-B3AG / ProLite TF4237MSC-B4AG 44.5mm/1.7” 69.5mm/2.7” 593.5mm/23.4” 187.5mm/7.4” 400.0mm/15.7” 200.0mm/7.8” 97.5mm/3.8” 429.5mm/16.9” 523.5mm/20.6” 575.0mm/22.6” 285.0mm/11.2” 287.5mm/11.3” POWER UP DOWN AUTO/EXIT SOURCE/OK MENU LED IR AC IN USB COM IN HDMI DVI IN VGA AUDIO IR IN IN 8xM6 SCREW HOLE (Outer) 24.0mm/0.9” 187.5mm/7.4” 200.0mm/7.8” 187.5mm/7.4” 4xM6 SCREW HOLE (VESA MOUNT) 287.5mm/11.3” 400.0mm/15.7” 287.5mm/11.
COMPLIANT TIMING Horizontal Frequency Vertical Frequency Dot Clock 640 × 480 31.469kHz 59.940Hz 25.175MHz 720 × 400 31.467kHz 70.080Hz 28.320MHz 800 × 600 37.879kHz 60.317Hz 40.000MHz 1024 × 768 48.363kHz 60.004Hz 65.000MHz 1280 × 720 44.720kHz 60.000Hz 74.500MHz 1280 × 768 47.776kHz 59.870Hz 79.500MHz 1280 × 1024 63.981kHz 60.020Hz 108.000MHz 1366 × 768 47.712kHz 59.790Hz 85.500MHz Video Mode VGA ENGLISH SVGA VESA XGA SXGA SD HD WSXGA+ 1680 × 1050 65.290kHz 59.
