Model ZN90 Dual Alarm Clock Radio for your Zune® Questions? Visit www.ihomeaudio.
Table of Contents Quick Start ........................................................................................................................................................................ 1 Controls and Indicators / ZN90 Display ......................................................................................................................... 2 Using the ZN90 .....................................................................................................................................
quick start 1:power 3:inserts 2:antenna Zune connector Attach AC adaptor cable to DC jack on back of the ZN90 and plug the other end into a wall socket. Snap AM antenna into stand, then plug antenna cable into socket on back of ZN90. Move antenna 12” away. Use this insert For this Zune ZuneHD Zune HD 16GB & 32GB Select the dock insert for your Zune model from the table below and place insert in dock. Slide the Zune connector to left or right to match proper insert if needed.
Controls and Indicators Dock EQ Button Preset Buttons Radio/line in Button Set Wheel Volume Wheel Play/Pause Button Alarm Reset / Power Button Alarm 2 Button Sleep Button Snooze/Dimmer Button Alarm 1 Button Clock Adjust Button Time Zone Button Line Out Jack DST switch AC Adaptor Jack Line-in Jack FM Antenna AM Loop Antenna socket ZN90 Display Time Display AM/PM Indicator Alarm 1, Alarm 2 Indicators Sleep Indicator Battery Low Indicator Wake-to Indicator Radio / Alarm Time / Zune Display 2
Using the ZN90 Connect ZN90 to Power Source Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 100-240 VAC wall socket. Adaptor must be plugged in to operate. The ZN90 does not operate on batteries. Setting the Clock a) To adjust the time for Daylight Saving Time, slide the DST switch to +1 to advance the time 1 hour. Slide to -1 to turn the clock back 1 hour. b) Press and hold the Time Zone Button until the display flashes. c) Turn the Set Wheel to select your time zone.
Using the ZN90 Radio Setting up Antennas a) Snap AM loop antenna into provided stand, then plug AM antenna cable into AM Loop Antenna socket on back of unit. Move antenna 12” away from unit for best reception. b) Extend FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas. c) Locate ZN90 and all antennas away from AC adaptor in wall socket (at least 3 feet) for best radio reception.
A Consumer Guide to Product Safety When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
Troubleshooting Symptom Possible Problem Solution ZN90 does not turn on AC adaptor isn't plugged into a working wall socket or not plugged into the power supply jack on back of the unit Plug the AC adaptor into a working wall socket and plug the connector into the supply jack on the unit ZN90 doesn’t respond ZN90 requires a reset If unit is plugged in and doesn't respond, try resetting the unit by following these steps: a) remove Zune from dock b) unplug unit from power source c) remove back up batt
Troubleshooting Symptom Sound is distorted Possible Problem Solution Volume level is set too high Decrease the volume Sound source is distorted If the Zune original sound source (MP3) is old or of poor quality, distortion and noise are easily noticed with high-power speakers. Try a different audio source such as a music CD. If you are using an external sound source, try reducing the output volume on the device itself. Also try turning bass boost OFF.
Solucionando problemas Síntoma Causa Solución La unidad no enciende El adaptador de corriente AC no está conectado a un tomacorriente que funcione o no está conectado en la parte posterior de la unidad Conecte el adaptador de corriente a un tomacorriente que funcione y a la parte posterior de la unidad La unidad no responde La unidad debe ser reprogramada Si la unidad está conectada y no responde, pruebe reprogramarla siguiendo estos pasos: a) Quite el Zune de la base b) Desconecte la unidad del tom
Solucionando problemas Síntoma El sonido sale distorsionado Causa Solución El volumen se encuentra muy alto Baje el volumen El sonido sale distorsionado de la unidad Si el sonido original de su Zune era de pobre calidad, las distorsiones y ruidos se harán más notables con los parlantes de alta potencia. Pruebe utilizar otra fuente de audio como un CD. Si tiene una fuente de sonido externa en uso, intente reducir el volumen de salida del aparato.
Limited 90-Day Warranty Information iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
