Model iP98 The Home System For Your iPhone® or iPod® Questions? Visit www.ihomeaudio.
Table of Contents Quick Start ........................................................................................................................................................................1 Controls and Indicators / iP98 Display ..........................................................................................................................2 Using the iP98 ......................................................................................................................................
quick start 1: power 2: antenna Attach AC adaptor cable to DC jack on back of the iP98 and plug the other end into a wall socket. Snap AM antenna into provided stand, then plug antenna cable into socket on back of iP98. Move antenna 12” away. NOTE: If you do not have an insert for your iPhone/iPod, please visit www.ihomeaudio.com or call iHome toll free at 877-446-6301 to purchase one.
Controls and Indicators Dock Radio Button Preset Buttons 1-6 Set Wheel Volume Wheel SPUL PU Play/Pause Button LX Alarm 2 Button Alarm Reset / Power Button Alarm 1 Button EQ Button Sleep Button Snooze/Dimmer Button Clock Adjust Button Time Zone Button Line-in Jack AC Adaptor Jack +* = T( DST switch JSVJR HKQ [PTL aVUL +:; HT HU[LUUH SPUL PU FM Antenna AM Loop Antenna socket iP98 Display Time Display Sleep Indicator PM Indicator Alarm 1, Alarm 2 Indicators Wake-to Ind
Using the iP98 Connect iP98 to Power Source Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120 VAC wall socket. Adaptor must be plugged in to operate. The iP98 does not operate on batteries. Setting the Clock a) b) c) d) Press and hold the Time Zone Button until the display flashes. Turn the Set Wheel to select your time zone. Press the Time Zone Button again. The clock will display the current time in your time zone.
Using the iP98 Radio Setting up Antennas a) Snap AM loop antenna into provided stand, then plug AM antenna cable into AM Loop Antenna socket on back of unit. Move antenna 12” away from unit for best reception. b) Extend FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas. Tuning and Playing the Radio a) Press the Radio Button to select radio play mode. Press as needed to select FM or AM radio band. b) Turn the Set Wheel to tune radio to a desired station.
Using The Remote Control Unit The Remote Control controls basic functions on the iP98 and certain iPhone®/iPod® functions when the iPhone®/iPod® is docked in the iP98. For best results, use the remote control within 12 feet of the unit. - Power /Alarm Reset Button: Turns iP98 ON or OFF or resets alarm when alarm is sounding - Fwd/Rev Button: Skip to previous or next track, or HOLD to scan current playing track; Also controls set wheel functions (changing settings, tuning radio, etc.
A Consumer Guide to Product Safety When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
Troubleshooting Symptom Possible Problem Solution iP98 does not turn on AC adaptor isn't plugged into a working wall socket or not plugged into the power supply jack on back of the unit Plug the AC adaptor into a working wall socket and plug the connector into the supply jack on the unit iP98 doesn’t respond iP98 requires a reset If unit is plugged in and doesn't respond, try resetting the unit by following these steps: a) remove iPhone/iPod from dock b) unplug unit from power source c) remove back
Troubleshooting Symptom Sound is distorted Possible Problem Solution Volume level is set too high Decrease the volume Sound source is distorted If the iPhone/iPod original sound source (MP3) is old or of poor quality, distortion and noise are easily noticed with high-power speakers. Try a different audio source such as a music CD. If you are using an external sound source like older generation of iPod or iPod Shuffle, try reducing the output volume on the device itself.
Solucionando problemas Causa Solución La unidad no enciende Síntoma El adaptador de corriente AC no está conectado a un tomacorriente que funcione o no está conectado en la parte posterior de la unidad Conecte el adaptador de corriente a un tomacorriente que funcione y a la parte posterior de la unidad La unidad no responde La unidad debe ser reprogramada Si la unidad está conectada y no responde, pruebe reprogramarla siguiendo estos pasos: a) Quite el iPod de la base b) Desconecte la unidad del tom
Solucionando problemas Síntoma Causa La banda de AM se escucha con distorsión La antena circular no está ubicada correctamente. Aleje la antena de la unidad y del adaptador AC y gírela hasta mejorar la recepción. Solución El sonido sale distorsionado El volumen se encuentra muy alto Baje el volumen El sonido sale distorsionado de la unidad Si el sonido original de su iPhone/iPod era de pobre calidad, las distorsiones y ruidos se harán más notables con los parlantes de alta potencia.
Limited 1 Year Warranty Information iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 1 Year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
