Installers & User guide Deadbolt 2S. Version 0.
Welcome! This guide will get you up and running with your igloohome Deadbolt 2S. In the meantime, you should follow igloohome on Facebook and Youtube! Like us on Facebook Visit our Youtube As our igloohome app is frequently updated, there may be changes to this manual. Please refer to our website igloohome.co/support for the latest version of the manual.
Table of Contents What’s Included 3 Specifications 4 Installation Guide Requirements 5 Prepare Door for Installation 6 Prepare Lock for Installation 7 Installation Instructions 9 Test Lock 13 Prepare the Door Frame 14 User Guide Lock Anatomy 15 Features 16 Unlocking and Locking 18 App Onboarding 19 Managing Access in App 20 Lock Tutorial 21 Lock Behaviour 22 Airbnb Connect 23 Troubleshooting 24
What’s Included Back Plate Back Assembly Rubber Gasket Front Assembly & Rubber Gasket Back Assembly AA Alkaline Batteries x4 Strike Plate Housing & Strike Plate Bolt Assembly Screw Holder 10mm (Optional) Drill for: 60mm (2-3/8”) backset Fold this line 03/18 Face of the door Drill for: 70mm (2-3/4”) backset Version 0.
Specifications Model igloohome Smart Deadbolt 2S Material Zinc Alloy, ABS Current Rating (Standby) ~30uA Current Rating (Active) ~200mA Batteries 4 x AA Alkaline Battery Life Up to 9 months Unlock Mechanism Bluetooth, PIN code, Physical Keys, Thumbturn Side Back 145mm (5-11/16”) 160mm (6-19/64”) Front 60mm (2-23/64”) 11mm (7/16”) 51mm (2-1/64”) 64.5mm (2-35/64”) * DO NOT USE: Heavy Duty, Eveready, GP, or rechargeable batteries.
Installation Guide Requirements Clearance Door Thickness a b 160mm (6-19/64”) 144.
Prepare Door for Installation Items needed: Drill Sheet #2 Phillips Screw Driver Recommended Door and door frame material : Wood Drill 25mm (1”) Spade Bit 10mm (25/64”) Drill Bit 20mm (25/32”) Chisel 54mm (2-1/8”) Hole Saw Hammer Recommended Gap between door and door frame: <3mm (1/8”) Please ensure that there is an existing handle on your door for push - pull access. Not for: metal gates, glass doors or sliding doors.
How to use the Drill Sheet Drilling (Door) Make sure this is aligned to the centre of door edge Fold here before drilling holes for side 25mm (1”) Spade Bit 54mm (2-1/8”) Hole Saw Door edge Chiselling Put the bolt tongue in & chisel around the edge Depth: 4.5mm (11/64”) or until bolt assembly plate is flush against door 20mm (25/32”) Chisel 20mm (25/32”) Chisel Mark the center of the holes and then drill for accuracy.
Prepare Lock For Installation Set Back Assembly for Left / Right Installation Left Installation Set the toggle to ‘L’ for left-side installation. L R Right Installation Set the toggle to ‘R’ for right-side installation. L R Remove Battery Cover from the Back Assembly Top View of Battery Cover Press the button on the top of the battery cover, and pull outwards.
Installation Instructions Measure If you are replacing your current deadbolt lock, industry standards are 60mm (2-3/8”) or 70mm (2-3/4”) backset. To determine which backset length you should use, so measure the distance (x) between the center of 54mm (2-1/8”) hole to door edge. 54mm (2-1/8”) Hole X Prepare bolt assembly based on the distance (x) Bolt ships with bolt assembly in 60mm (2-3/8”) position. If required, twist the bolt and pull to extend (simultaneously) to 70mm (2-3/4”) backset position.
Insert bolt and front assembly into door edge The ‘+ ‘ hole on the backset should be in the middle of the hole. Screw Holder c c Screws Please ensure that tailpiece is in vertical position. 15mm (19/32”) Measure and cute the tailpiece if necessary After inserting the tailpiece, measure the distance of protrusion from the door. Notch Door thickness (mm) No. of notch to cut 60 0 55 1 45 2 40 3 35 4 The recommended tailpiece protrusion from the door is 15mm.
Secure the Front Assembly using the Back Plate. To do this, place the Back Plate (ensuring the correct side placement). d d Follow this orientation Screws d 43mm (1-11/16”) 5 Door Sensor Installation Adjust the position of the door sensor according to the door handling (left or right installation). Use the 2 x 5 (13/64) mm screws to secure the door sensor to the back plate.
6 Fit in the Rubber Gasket Insert the front assembly cable through the rectangular hole on the rubber gasket. The hole should be on the right side of the rubber gasket.
7 Connect Assembly Cable Connect the sensor cable to the Back Assembly then connect the assembly cable from the Front assembly through the 54mm hole to the Back Assembly. Ensure that the wire is installed properly and securely. Door Sensor Cable Assembly Cable 8 LR Fit Back Assembly to the Door Tailpiece Ensure thumbturn position is turned to ‘unlock’ position.
9 Secure the Back Assembly Do not overtighten the screws Screws 8mm (5/16”) 20mm (25/32”) 10 Insert 4 AA Alkaline Batteries and push the battery case lid inwards to close Side View 15
Test Lock Place hand over your lock to activate touchpad and hold # to lock. Does your bolt lock? Yes No Congrats! Your lock is correctly installed. Proceed to next steps. Bummer! Does the bolt lock and unlock when you turn the thumbturn? Yes No Left-Right toggle incorrectly set Tailpiece and/or thumbturn incorrectly set Troubleshoot: Try Setting the left-right toggle on your back assembly to the correct side. (See Pg. 10) Still experiencing issues? Go to igloohome.
Prepare the Door Frame Mark out where the bolt tongue locks then drill a corresponding hole on door frame. Chisel to fit the strike plate in as well. Ensure to align the lock to the door frame and mark it down. Door Frame 20mm (25/32”) Chisel 25mm (1”) Spade Bit 26mm (1-1/32” ) Mark & Drill Hole 58mm (2-9/32”) Same height Secure strike plate housing and strike plate using 2x 25mm (1”) wood screws.
User Guide Lock Anatomy Outer Body Battery Cover Release Touch Screen Keypad Battery Cover Key hole Cover (Remove cover to access physical key unlock) Thumbturn Privacy Lockout Button 9V Jumpstart 18
Features PIN / Bluetooth Unlock Bluetooth Master Key Master PIN Code The igloohome Smart Deadbolt 2S unlocks with Bluetooth via the app. The igloohome Smart Deadbolt 2S unlocks with a permanent Master PIN Code. Bluetooth Guest Key User PIN Code Bluetooth keys based on duration can be generated and shared with guests. The mobile app can generate user PIN codes, with validity duration from One-Time, Permanent, or a Duration based on Date-time.
Features Security / Alarms Security Lockout Mode Activity Logs After 5 consecutive unsuccessful attempts at entering a PIN code, the igloohome Smart Deadbolt 2S will be unresponsive for 5 minutes. Physical key and Bluetooth Unlock can be used to unlock in this state. Entry via PIN codes and Bluetooth Key will be logged in the app. Privacy Lockout Mode Tamper Alarm Activate this from indoors to prevent entry from outsiders. Physical key can be used to unlock in this state.
Unlocking & Locking Sensor Re-Lock (Recommended Accessory) PIN Code / Decoy PIN Code igloohome App Bluetooth Basic Unlock Main Door Thumbturn Physical Key Unlocking PIN Code Key in your PIN code and press ‘#’ Bluetooth Guest Key Refer to page 23 Bluetooth Basic Unlock On your app, click on the Bluetooth Unlock button and tap on your lock Physical Key Use the physical key to unlock the door Thumbturn Use thumbturn at the back of lock Locking ‘#’ Key Press and hold ‘#’ Physical Key Use the physical
App Onboarding Test Factory PIN Unlock In the factory mode (before pairing), the PIN to unlock is * 1234567890 # 2 Register as a Lock User a) Download igloohome from App store / Play store. b) Create an account and login. 3 Pairing a) Select [Add new igloohome lock] Note: For exitisting users with other paired locks, go to [Configuration], select [Manage Locks] followed by the [Add] icon.
Managing Access in App Creating PIN codes PIN codes can be generated on the app under [Access], create [New Key] and choose either One-Time, Permanent or Duration PIN. Pin codes will expire if its not use within its activation period. Refer to the table below. 2 PIN Type Use PIN within* One-Time PIN 6 hrs of generation Permanent PIN 24hrs of generation Duration PIN 24hrs from the start time Bluetooth Guest Key Bluetooth Guest Key can be shared with other users for mobile access.
Lock Tutorial Edit PIN codes Once PIN code is generated, user must key the generated code onto the Deadbolt 2S keypad followed by # to activate the code before proceeding.
Lock Behaviour 4 Security Lockout Mode After 5 consecutive unsuccessful attempts at entering a PIN code, the igloohome Samrt Deadbolt 2S will be unresponsive for 5 minutes. Note: Physical key and Bluetooth Unlock can be used to unlock in this mode. 5 Privacy Lockout Mode Privacy Lockout Mode prevents others from using PIN code and Bluetooth Key to unlock when you are inside the property. Note: Physical key can be used to unlock in this mode.
Airbnb Connect 7 8 Airbnb Connect Airbnb Connect automates the generation of PIN codes for your Airbnb guests based on their approved reservations. It costs USD$4.99 per month, but is currently on free trial. Here are the steps to activate Airbnb Connect Step 1: Connect to your Airbnb Under [Account Settings], select [Connect with Airbnb] Step 2: Connect to Airbnb listings Under [Reservations], click the [Add] icon to select a home to connect to. Select Airbnb Listing and PIN Time to associate.
Troubleshoot Pairing is unsuccessful • Try with a different mobile device, using the same username and password • Update your phone’s Operating system to the latest version • Restart the Bluetooth and internet connection on your mobile device • Restart igloohome app on your mobile device • Switch to a new set of batteries Lock is not working when battery level is not 100% • Do a Bluetooth Key unlock to refresh the battery level on the app • Battery level shown in the app may not be accurate • Use Alkaline
For enquiries go to: igloohome.
