Hy, gy, fall PRO LI AQUA Professional Water Filtration Systems www.proaguawater.com.
NNN TABLE OF CONTENT Introduction / System Specifications 1. Principles of Reverse Osmosis Reverse Osmosis Prices: Semipermeable membrane . Factors affecting membrane service life Reverse Osmosis System Terms and Definitions ..
INSPECTION & PREPARATION INTRODUCTION Water Is an important part of all process applications. In order to always provide the highest quality of water to the end consumer, we must make sure to have all the required parameters for each application. Comet information is important in order to safeguard the welfare of consumers when it comes to water quality for food processing, beverages or whatever the final application may be. Proper selection of treatment technology must be evaluated in a case by case basis.
PRINCIPLES OF REVERSE OSMOSIS 1 > Principles of Reverse Osmosis Technology How the Reverse Osmosis process works? Reverse Osmosis (RO) Is a process in which water Is forced to pass through a semipermeable membrane by pressure, As the water passes through the membrane dissolved particles are rejected remembrance nits spiral layers of semipermeable material formed around a central perforated tube.
PRINCIPLES OF RO & IDENTIFYING SYSTEM COMPONENTS Feed Water Requirements TYPICAL EXPECTED ION RETENTION IN AFC MEMBRANE TYPE: Typical Expected lon Detention In A TTc Membrane Type Sodium 85-94% Lead 95-98% Sulfate 96-98 % Arsenic 92-96 % Calcium 94-98% Magnesium 94-98 % Potassium 85-95% Nickel 96-98% Nitrate 60-75% Fluoride 85-92% Iron 94-98% Manganese 94-98 % Zine 95-98% Cadmium 95-98% Mercury 95-98 % Barium 95-98% Selenium 94-96 % Cyanide 84-92% Phosphate 96-98% Chloride 85-92% WATER SUPPLY REQUIREMENTS:
IDENTIFYING SYSTEM COMPONENTS Turning the valve knob will control the ratio of water discharged / water produced. Turning clockwise will increase pressure inside of the module and reduce the amount of waste water. turning counterclockwise pressure will decrease within the module and increase the amount of waste water. CAUTION! Keep in mind the recovery (product / rejection) suggested by your dealer based on water analysis done. i > CAUTION! Waste valve should never be completely shut.
PRE INSTALLATION REFERENCES & REVERSE OSMOSIS SYSTEM INSTALLATION 3 > PRE INSTALLATION REFERENCES Inlet Feed Water enters through the per-filter housing. The housing connection depending on the model. We suggest system connections are made preferably with PVC SCH 80 or SCH 40. Outlet Product Water On PROPER systems, the permeate water output exits through the product water flow meter. through the back of the system.
CONTROLLER PROGRAMMING > PROGRAMMING THE CONTROLLER NAVIGATION AND PROGRAMMING MENU: (00:00) (000 SET key, is access to settings mode UP key increases the setting values DOWN key decreases the setting values Main screen: Displays the operating status: 00:00 (000 HH gp BEY © Gis FLUSH (Activated) Purges at low pressure {Valid on systems with Fast Flush option) LOW Indicates that the system Is protected by low pressure and is off (standby) until there is sufficient Inlet pressure to restore system operation,
CONTROLLER PROGRAMMING INFORMATION DISPLAYED ON SCREEN: Timer Indicates the time the system has been working and starts measuring a range of time (minutes: seconds), after an hour of operation this changes its time reference to: (hour: minute). You can also view here when the membrane is in fast flush mode. It will display a countdown in seconds. When the system is on (stand by) but has the power Ont he control will save information showing how long the System has been operating.
CONTROLLER PROGRAMMING CABLE CONNECTION IDENTIFICATION: Violet: Green: Yellow: Gray: Orange: Red: Black: Low level Switch In the raw water tank (SW1) Shut-Off Switch for the per-treatment (SW2) (% Storage tank level switch (FULL) Low pressure switch (LOW} Booster Pump System Solenoid Valve for membrane flush ( FLUSH) High Pressure Pump System Solenoid Valve water feed system Power 110V-240V ) Deactivated in PROPER models | SEMIRETIRED TTT TTT -10TDS SENSOR CALIBRATION (CONTROLLER): The controller has a basi
START-UP 7 > START-UP 1. Make sure that everything related to the per-treatment process Is operating properly and has been back washed several times to avoid fines from entering the system. 2. Tum the switch on the control box to AUTO. The indicator light on the display lights and the low pressure indicator is activated. 3. All pressure gauges will read 0. 4, Activate the feed water by opening the supply valve to the system. 5. Make sure the waste and re circulation valve are fully open. 6.
TROUBLESHOOTING GUIDE 8 > TROUBLESHOOTING GUIDE A) Power switch off, A) Place In AUTO position. B1) Check power outlet and make sure system Is plugged in. B) No power. B2) Check AMP fuse on back of controller. Cl) Verify that the feed valve Is fully open. €2) Make sure your per-treatment pump is operating properly to supply pressure to the reverse osmosis system. €} Not enough inlet pressure and the low pressure switch Is not activated.
TROUBLESHOOTING GUIDE A) saturated or dirty membrane. A) Check, dean, replace If necessary. B) Check your feed water temperature, check your correction 4) No product or too 8) The water temperature Is very low. factor for the temperature and make sure that the flow is at an little water production. acceptable level. ©) Check other causes mentioned in this manual under issues. ©) Low pressure In the system. hot having enough pressure A) Waste valve open, check and adjust. A) Low pressure In the system.
REVERSE OSMOSIS PER-TREATMENT PER-TREATMENT REQUIRED FOR REVERSE OSMOSIS SYSTEMS. This flow chart shows the typical per-treatment and post treatment equipment to complete the purification process, For this process to work properly you will need to make the final selection of the most appropriate maltreatment, per the characteristics of incoming water to ensure that your reverse osmosis system will work efficiently. Selection of post treatment is also recommended to achieve a final quality of water desired.
WARRANTY PRO+AQUA warrants that your new PROPER System is built of quality materials and workmanship. When properly installed and maintained, it will give years of trouble free service. One Year Guarantee PRO+AQUA will replace any part that fails within (1) one years from date of purchase, provided the failure is due to a defect in material or workmanship. The only exception shall be when proof of purchase and installation is provided. The warranty period shall be from the date of purchase.
fw ¥ oY Fun 8 PRO LI ACUFF Professional Water Filtration Systems www. proaquawater.com.com © Copyright PRO+AQUA. All Rights Reserved.
