Owner's manual

ManualsBrandsIEI Integration ManualsComputer AccessoriesTANK-820-H61 v2.03

TANK-820-H61 Embedded System

Page i

User Manual

MODEL:

TANK-820-H61 Series

Embedded System with 2nd Generation Intel® Core™ desktop

processor, VGA, DVI-I, Tw o Gigabit Ethernet,

Four USB 2.0, Tw o USB 3.0, RS-232/422/485,

RoHS Compliant

Re v. 2.03 – 27 December 2013

Summary of content (157 pages)

PAGE 1
TANK-820-H61 Em be d d e d S ys te m MODEL: TANK-820-H61 S e rie s Em b e d d e d S ys te m with 2n d Ge n e ra tio n In te l® Co re ™ d e s kto p p ro c e s s o r, VGA, DVI-I, Two Gig a b it Eth e rn e t, Fo u r US B 2.0, Two US B 3.0, RS -232/422/485, Ro HS Co m p lia n t Us e r Ma n u a l Page i Re v. 2.
PAGE 2
TANK-820-H61 Em be d d e d S ys te m Re vis io n Date Version Changes 27 December 2013 2.03 Update BIOS version Updated Section 3.4: System Fan Installation 16 July 2013 2.02 Update Section 1.4: Technical Specifications (Operating Temperature : -20°C ~ 55°C) 19 June 2013 2.01 Update Section 1.2: Model Variations 22 May 2013 2.00 Change to fanless design 2 April 2013 1.01 Add backplane max. size 12 December 2012 1.
PAGE 3
TANK-820-H61 Em be d d e d S ys te m Co p yrig h t COP YRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
TANK-820-H61 Em be d d e d S ys te m Ta b le o f Co n te n ts 1 INTRODUCTION ........................................................................................................... 1 1.1 OVERVIEW................................................................................................................... 2 1.2 MODEL VARIATIONS ..................................................................................................... 3 1.3 FEATURES ........................................................
PAGE 5
TANK-820-H61 Em be d d e d S ys te m 3.7.8 Power Input, 3-pin Terminal Block .................................................................. 31 3.7.9 Power Input, 4-pin DIN Connector ................................................................. 31 3.7.10 RJ-45 RS-422/485 Serial Ports ...................................................................... 31 3.7.11 RS-232 Serial Port Connectors ...................................................................... 32 3.7.12 USB Connectors .............
PAGE 6
TANK-820-H61 Em be d d e d S ys te m 4.3.5 Ethernet and USB2.0 Connectors (USBLAN2) ................................................ 49 4.3.6 Power Connector (PWR2) ............................................................................... 50 4.3.7 Power Connector (PWR1) ............................................................................... 50 4.3.8 RS-232 Serial Port Connector (COM1) ........................................................... 50 4.3.9 RS-232 Serial Port Connector (COM2) .....
PAGE 7
TANK-820-H61 Em be d d e d S ys te m 5.3.10.1 Smart Fan Mode Configuration .............................................................. 77 5.3.11 Serial Port Console Redirection..................................................................... 81 5.3.11.1 Console Redirection Settings................................................................... 82 5.3.12 iEi Feature...................................................................................................... 85 5.4 CHIPSET.................
PAGE 8
TANK-820-H61 Em be d d e d S ys te m A.6.6 Setup a Client System for Auto Recovery ...................................................... 130 A.7 OTHER INFORMATION ............................................................................................. 133 A.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller ....................... 133 A.7.2 System Memory Requirement ........................................................................ 135 B SAFETY PRECAUTIONS ................................
PAGE 9
TANK-820-H61 Em be d d e d S ys te m Lis t o f Fig u re s Figure 1-1: TANK-820-H61 .............................................................................................................2 Figure 1-2: TANK-820-H61 Front Panel ........................................................................................6 Figure 1-3: TANK-820-H61 Rear Panel..........................................................................................7 Figure 1-4: TANK-820-H61 LED Indicators .......................
PAGE 10
TANK-820-H61 Em be d d e d S ys te m Figure 3-24: USB Device Connection .........................................................................................34 Figure 3-25: VGA Connector .......................................................................................................35 Figure 3-26: VGA Connector .......................................................................................................35 Figure 3-27: Power Button ........................................................
PAGE 11
TANK-820-H61 Em be d d e d S ys te m Figure A-23: Launching the Recovery Tool .............................................................................113 Figure A-24: Auto Recovery Environment for Windows ........................................................113 Figure A-25: Building the Auto Recovery Partition .................................................................114 Figure A-26: Factory Default Image Confirmation ..................................................................
PAGE 12
TANK-820-H61 Em be d d e d S ys te m Lis t o f Ta b le s Table 1-1: TANK-820-H61 Model Variations .................................................................................3 Table 1-2: Technical Specifications ..............................................................................................5 Table 1-3: LED Indicators Description..........................................................................................8 Table 1-4: Supported Signals ........................................
PAGE 13
TANK-820-H61 Em be d d e d S ys te m Table 4-24: RS-232 Serial Port Connector Pinouts (COM8) .....................................................51 Table 4-25: RS-422/485 Serial Port Connectors Pinouts (LANCOM3) .....................................52 Table 4-26: USB 3.0 Connectors Pinouts (USB3_12) ................................................................52 Table 4-27: VGA Connector Pinouts (VGA1) .............................................................................53 Table 4-28: Jumper ...
PAGE 14
TANK-820-H61 Em be d d e d S ys te m Ch a p te r 1 1 In tro d u c tio n Page 1
PAGE 15
TANK-820-H61 Em be d d e d S ys te m 1.1 Ove rvie w Figure 1-1: TANK-820-H61 The TANK-820-H61 is an embedded system for wide range temperature environments. It is powered by the 2nd Generation Intel® Core™ low power desktop processor, uses the Intel® H61 chipset and has 2.0 GB of DDR3 memory on-board. The TANK-820-H61 series includes one VGA port, one DVI-I port, two GbE LAN ports, four USB 2.0 ports, two USB 3.0 ports, six RS-232 connectors and two RS-422/485 connectors.
PAGE 16
TANK-820-H61 Em be d d e d S ys te m 1.2 Mo d e l Va ria tio n s The model variations of the TANK-820-H61 series are listed below. Model No.
PAGE 17
TANK-820-H61 Em be d d e d S ys te m S p e c ific a tio n s Me m o ry 1 x 204-pin DDR3 SDRAM SO-DIMM slot (Max. to 10G) On-board 2GB DDR3 memory Eth e rn e t Co n tro lle r Dual Realtek RTL8111E PCIe GbE controllers with ASF 2.0 support I/O a n d In d ic a to rs Eth e rn e t 2 x RJ-45 GbE ports RS -232 4 x RS-232 serial ports (DB-9) 2 x RS-232 serial ports (DB-9 with isolation) RS -422/RS -485 2 x RS-422/485 serial ports (RJ-45) US B In te rfa c e s 4 x USB 2.0 ports on front side 2 x USB 3.
PAGE 18
TANK-820-H61 Em be d d e d S ys te m S p e c ific a tio n s P o we r P o we r S u p p ly Redundant dual DC input Terminal Block: 9 ~ 24V DC Jack: 9 ~ 24V P o we r Co n s u m p tio n 19V@3.
PAGE 19
TANK-820-H61 Em be d d e d S ys te m 1.
PAGE 20
TANK-820-H61 Em be d d e d S ys te m  4 x USB 2.0 ports  1 x Reset button  6 x LED indicators (Section 1.7)  1 x Power button  1 x CompactFlash® Type II socket  1 x VGA port  1 X DVI-I port  1 x To Ground  3 x Expansion slots  1 x ACC mode switch  1 x AT/ATX mode switch 1.
PAGE 21
TANK-820-H61 Em be d d e d S ys te m 1.7 LED In d ic a tors There are several indicators on the rear panel of the TANK-820-H61 as shown in Figure 1-4. Figure 1-4: TANK-820-H61 LED Indicators The descriptions of each LED indicator are listed below. LED In d ic a to r De s c rip tio n AT Power Mode The current power mode status is AT mode. Controlled by the AT/ATX power mode switch. ATX Power Mode The current power mode status is ATX mode. Controlled by the AT/ATX power mode switch.
PAGE 22
TANK-820-H61 Em be d d e d S ys te m 1.8 Ba c kp la n e Op tio n s The backplane options of the TANK-820-H61 are shown below. Figure 1-5: HPE-3S6 (2P1E) Figure 1-6: HPE-3S7 (1P2E) The supported signals of the backplane slots are listed below. Ba c kp la n e S lo t S ig n a l PCI PCI PCIe x16 PCIe x8 PCI PCI PCIe x4 PCIe x1 PCIe x16 PCIe x8 HP E-3S 6 (2P 1E) HP E-3S 7 (1P 2E) Table 1-4: Supported Signals The rated voltage and current of the backplanes are listed below.
PAGE 23
TANK-820-H61 Em be d d e d S ys te m +12 V 3.75 A -12 V 0.1 A +3.3 V 8A Table 1-5: Rated Voltage and Current WARNING: The system default power is 120 W. The maximum total power of the backplane to support expansion cards is 45 W. The power of the selected expansion cards can not exceed the max. power (45 W), otherwise, the system may be unstable.
PAGE 24
TANK-820-H61 Em be d d e d S ys te m 1.
PAGE 25
TANK-820-H61 Em be d d e d S ys te m Ch a p te r 2 2 Un p a c kin g P a g e 12
PAGE 26
TANK-820-H61 Em be d d e d S ys te m 2.1 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during installation may result in permanent damage to the TANK-820-H61 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TANK-820-H61. Dry climates are especially susceptible to ESD.
PAGE 27
TANK-820-H61 Em be d d e d S ys te m 2.3 Un pa c kin g Ch e c klis t NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the TANK-820-H61 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw.
PAGE 28
TANK-820-H61 Em be d d e d S ys te m Qu a n tity Ite m a n d P a rt Nu m b e r Im a g e S ta n d a rd 2 Mounting Brackets (P/N: 41020-0366E4-00-RS) 4 HDD Screws (P/N: 44043-030051-RS) 4 Rubber Foot Pad Screws (P/N: 44033-040061-RS) 4 Rubber Foot Pads (P/N: 46015-006300-RS) 2 RJ-45 to DB-9 COM Port Cable (P/N: 32005-000200-200-RS) 1 Pluggable DC-in Terminal Block (P/N: 33502-000007-RS) 1 One Key Recovery CD (P/N: 7B000-000724-RS) 1 User Manual and Driver CD 4 Fan Screws (P/N: 44003-030151
PAGE 29
TANK-820-H61 Em be d d e d S ys te m The following table lists the optional items that can be purchased separately. Op tio n a l System Fan (50mmx50mmx15mm) (P/N: 31100-000340-RS) OS: Win CE 6.
PAGE 30
TANK-820-H61 Em be d d e d S ys te m Ch a p te r 3 3 In s ta lla tio n P a g e 17
PAGE 31
TANK-820-H61 Em be d d e d S ys te m 3.1 In s ta lla tio n P re c a u tio n s During installation, be aware of the precautions below:  Read the user manual: The user manual provides a complete description of the TANK-820-H61, installation instructions and configuration options.  DANGER! Disconnect Power: Power to the TANK-820-H61 must be disconnected during the installation process, or before any attempt is made to access the rear panel.
PAGE 32
TANK-820-H61 Em be d d e d S ys te m Figure 3-1: CF Card Socket S te p 2: Open the CF card socket cover (Figure 3-2). Figure 3-2: CF Card Socket Cover S te p 3: Correctly align the CF card with the socket and insert the CF card into the socket (Figure 3-3).
PAGE 33
TANK-820-H61 Em be d d e d S ys te m Figure 3-3: CF Card Installation S te p 4: Reinstall the cover. 3.3 Ha rd Dis k Drive (HDD) In s ta lla tio n To install the hard drive, please follow the steps below: S te p 1: Remove the two retention screws on the rear panel and loosen the two thumbscrews on the front panel, slide the cover inwards, and then lift the cover up gently (Figure 3-4).
PAGE 34
TANK-820-H61 Em be d d e d S ys te m S te p 2: Unplug the SATA signal and power cables connected to the TANK-820-H61, and then put the cover on a flat surface (Figure 3-5). Figure 3-5: Remove the Cover from TANK-820-H61 S te p 3: Attach the HDD to the HDD bracket, and then slide the HDD to connect the HDD to the SATA connector (Figure 3-6).
PAGE 35
TANK-820-H61 Em be d d e d S ys te m S te p 4: Secure the HDD with the HDD bracket by four retention screws (Figure 3-7). Figure 3-7: HDD Retention Screws S te p 5: Reconnect the SATA signal and power cables to the TANK-820-H61. S te p 6: Reinstall the cover. 3.
PAGE 36
TANK-820-H61 Em be d d e d S ys te m Figure 3-8: System Fan Installation S te p 4: Connect the system fan cable to the CPU_FAN1 connector on the motherboard of TANK-820-H61. S te p 5: Reconnect the SATA signal and power cables to the TANK-820-H61. S te p 6: Reinstall the cover. 3.5 Mo u n tin g th e S ys te m with Mo u n tin g Bra c ke ts To mount the embedded system onto a wall or some other surface using the two mounting brackets, please follow the steps below.
PAGE 37
TANK-820-H61 Em be d d e d S ys te m Figure 3-9: Mounting Bracket Retention Screws S te p 3: Secure the brackets to the system by inserting two retention screws into each bracket (Figure 3-9). S te p 4: Drill holes in the intended installation surface. S te p 5: Align the mounting holes in the sides of the mounting brackets with the predrilled holes in the mounting surface. S te p 6: Insert four retention screws, two in each bracket, to secure the system to the wall. 3.
PAGE 38
TANK-820-H61 Em be d d e d S ys te m Figure 3-10: Foot Pad Installation 3.7 Exte rn a l P e rip h e ra l In te rfa c e Co n n e c to rs The TANK-820-H61 has the following connectors. Detailed descriptions of the connectors can be found in the subsections below.
PAGE 39
TANK-820-H61 Em be d d e d S ys te m  RS-422/485  USB  VGA 3.7.1 ACC Mo d e S e le c tio n The TANK-820-H61 allows turning the ACC mode on or off. The setting can be made through the ACC mode switch on the external peripheral interface panel as shown below. Figure 3-11: ACC Mode Switch 3.7.2 AT/ATX P owe r Mo d e S e le c tio n The TANK-820-H61 supports AT and ATX power modes. The setting can be made through the AT/ATX power mode switch on the external peripheral interface panel as shown below.
PAGE 40
TANK-820-H61 Em be d d e d S ys te m Figure 3-12: AT/ATX Power Mode Switch 3.7.3 Au d io Co n n e c to r The audio jacks connect to external audio devices.  Line Out port (Green): Connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers.  Microphone (Pink): Connects a microphone. Figure 3-13: Audio Connector 3.7.4 Co m pa c tFla s h ® Typ e II The TANK-820-H61 has one CF Type II socket. The location of the socket is shown in Figure 1-2.
PAGE 41
TANK-820-H61 Em be d d e d S ys te m 3.7.5 Dig ita l In p u t/Ou tp u t Co n n e c to r The digital I/O connector provides programmable input and output for external devices. The pinouts for the digital I/O connector are listed in the table below. Figure 3-14: DIO Connector 3.7.6 DVI Co n n e c to r The TANK-820-H61 has one female DVI-I connector on the front panel. The DVI connectors are connected to digital display devices.
PAGE 42
TANK-820-H61 Em be d d e d S ys te m Figure 3-15: DVI Connector S te p 4: Secure the connector. Secure the DVI connector from the digital display device to the external interface by tightening the two retention screws on either side of the connector. 3.7.7 LAN Co n n e c to rs The LAN connectors allow connection to an external network. S te p 1: Locate the RJ-45 connectors. The locations of the RJ-45 connectors are shown in Figure 1-2. S te p 2: Align the connectors.
PAGE 43
TANK-820-H61 Em be d d e d S ys te m Figure 3-16: LAN Connection S te p 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the on-board RJ-45 connector. Figure 3-17: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked. See Table 3-1.
PAGE 44
TANK-820-H61 Em be d d e d S ys te m 3.7.8 P owe r In p u t, 3-p in Te rm in a l Blo c k The power connector connects the leads of a 9 V~24 V DC power supply into the terminal block. Make sure that the power and ground wires are attached to the correct sockets of the connector. Figure 3-18: 3-pin Terminal Block 3.7.9 P owe r In p u t, 4-p in DIN Co n n e c to r The power connector connects to the 9 V~24 V DC power adapter. Figure 3-19: Power Input Connector 3.7.
PAGE 45
TANK-820-H61 Em be d d e d S ys te m Figure 3-20: RJ-45 RS-422/485 Serial Device Connection S te p 3: Insert the serial connector. Insert the DB-9 connector of a serial device into the DB-9 connector on the RJ-45 to DB-9 COM port cable. S te p 4: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Figure 3-21: RJ-45 RS-422/485 Serial Port Connector 3.7.
PAGE 46
TANK-820-H61 Em be d d e d S ys te m Figure 3-22: Serial Device Connector S te p 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Figure 3-23: DB-9 RS-232 Serial Port Connector 3.7.12 US B Co n n e c to rs The USB ports are for connecting USB peripheral devices to the system. S te p 1: Locate the USB connectors. The locations of the USB connectors are shown in Figure 1-2.
PAGE 47
TANK-820-H61 Em be d d e d S ys te m Figure 3-24: USB Device Connection S te p 3: Insert the device connector. Once aligned, gently insert the USB device connector into the on-board connector. 3.7.13 VGA Co n n e c to r The VGA connector connects to a monitor that accepts VGA video input. S te p 1: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Figure 1-2. S te p 2: Align the VGA connector.
PAGE 48
TANK-820-H61 Em be d d e d S ys te m Figure 3-25: VGA Connector S te p 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector. Figure 3-26: VGA Connector 3.8 P owe rin g On /Off th e S ys te m WARNING: Make sure a power supply with the correct input voltage is being fed into the system.
PAGE 49
TANK-820-H61 Em be d d e d S ys te m  Power on the system: press the power button for 3 seconds  Power off the system: press the power button for 6 seconds Figure 3-27: Power Button 3.9 P owe r The TANK-820-H61 embedded system supports single DC power input mode, but can be simultaneously connected to two power sources. When both power connectors are connected to power sources, prior to use the corresponding power supply which with higher voltage. There are two power connectors on the rear panel.
PAGE 50
TANK-820-H61 Em be d d e d S ys te m Figure 3-28: Power Connectors LED In d ic a to r De s c rip tio n Power 1 Breathing Orange: Standby mode. Power 2 Solid blue: Power-on mode. Table 3-2: Power LED Indicators Description 3.9.1 ACC ON NOTE: In ACC On mode, the Power 1 connector must connect to ACC on signal to be able to control the system power. The ACC On mode is designed for vehicle applications. 3.9.1.
PAGE 51
TANK-820-H61 Em be d d e d S ys te m low to high. The system will detect the Power1 and Power2 voltages and prior to use the corresponding power supply which with higher voltage. The user can choose to use AT power mode or ATX power mode to control the system. The following flow diagrams show the boot-up process and the LED status in AT and ATX power modes. Figure 3-29: ACC On: AT Mode Figure 3-30: ACC On: ATX Mode 3.9.1.
PAGE 52
TANK-820-H61 Em be d d e d S ys te m Figure 3-31: ACC On: Shutdown NOTE: To turn on the system in the ATX power mode, press the Power button for three seconds. Press the Power button for six seconds to turn off the system. 3.9.2 ACC OFF When the TANK-820-H61 is in the ACC Off mode, the system does not require an external ACC on signal. 3.9.2.
PAGE 53
TANK-820-H61 Em be d d e d S ys te m Figure 3-33: ACC Off: ATX Mode 3.9.2.2 S h u td own The system will shutdown in the following situations:  Power 1 < 9 V and Power 2 < 9 V  Press Power buttons for 6 seconds The following flow diagram shows the system shutdown process and the LED statuses. Figure 3-34: ACC Off: Shutdown NOTE: The power LED turns off when the power cable is unplugged from the system.
PAGE 54
TANK-820-H61 Em be d d e d S ys te m Chapter 4 4 S ys te m Mo th e rb o a rd P a g e 41
PAGE 55
TANK-820-H61 Em be d d e d S ys te m 4.1 Ove rvie w This chapter details all the jumpers and connectors of the system motherboard. 4.1.1 La yo u t The figures below show all the connectors and jumpers of the system motherboard. The Pin 1 locations of the on-board connectors are also indicated in the diagram below.
PAGE 56
TANK-820-H61 Em be d d e d S ys te m Figure 4-2: System Motherboard (Rear) 4.2 In te rn a l P e rip h e ra l Co n n e c to rs The table below shows a list of the internal peripheral interface connectors on the system motherboard. Pinouts of these connectors can be found in the following sections.
PAGE 57
TANK-820-H61 Em be d d e d S ys te m Co n n e c to r Typ e La b e l SATA power connector 2-pin wafer CN1 SMBus connector 4-pin wafer CN3 TPM connector 20-pin header TPM1 Table 4-1: Peripheral Interface Connectors 4.2.1 Ba tte ry Co n n e c to r (BAT1) PIN NO. DESCRIPTION 1 VBATT 2 GND Table 4-2: Battery Connector Pinouts (BAT1) 4.2.2 BIOS P ro g ra m m in g Co n n e c to r (S P I2) PIN NO. DESCRIPTION PIN NO.
PAGE 58
TANK-820-H61 Em be d d e d S ys te m 5 EC_EPP_PD1 6 EC_EPP_INIT# 7 EC_EPP_PD2 8 EC_EPP_SLIN# 9 EC_EPP_PD3 10 GND 11 EC_EPP_PD4 12 EC_EPP_ACK# 13 EC_EPP_PD5 14 EC_EPP_BUSY 15 EC_EPP_PD6 16 EC_EPP_PE 17 EC_EPP_PD7 18 EC_EPP_SLCT Table 4-5: EC Debug Connector Pinouts (CN4) 4.2.5 EC P ro g ra m m in g Con n e c to r (J S P I1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 +V3.
PAGE 59
TANK-820-H61 Em be d d e d S ys te m 4.2.8 S ATA 3Gb /s Drive Co n n e c to rs (S ATA1) PIN PIN NO. DESCRIPTION 1 GND 2 SATA20_PTX_C_DRX_P2 3 SATA20_PTX_C_DRX_N2 4 GND 5 SATA20_PRX_C_DTX_N2 6 SATA20_PRX_C_DTX_P2 7 GND 8 GND 9 SATA20_PTX_C_DRX_P3 10 SATA20_PTX_C_DRX_N3 11 GND 12 S ATA20_PRX_C_DTX_N3 13 SATA20_PRX_C_DTX_P3 14 GND NO. DESCRIPTION Table 4-9: SATA 3Gb/s Drive Connectors Pinouts (SATA1) 4.2.9 S ATA P o we r Co n n e c to r (CN1) PIN NO.
PAGE 60
TANK-820-H61 Em be d d e d S ys te m 7 LPC_AD3 8 LPC_AD2 9 +V3.3S 10 LPC_AD1 11 LPC_AD0 12 GND 13 SMBCLK_MAIN 14 SMBDATA_MAIN 15 +V3.3A 16 INT_SERIRQ 17 GND 18 PM_CLKRUN# 19 PM_SUS_STAT# 20 SIO_DRQ#0 Table 4-12: TPM Connector Pinouts (TPM1) 4.3 Exte rn a l In te rfa c e P a n e l Co n n e c to rs The table below shows a list of the external interface panel connectors on the system motherboard. Pinouts of these connectors can be found in the following sections.
PAGE 61
TANK-820-H61 Em be d d e d S ys te m 1 GND 2 ILMIC1-L 3 GND 4 IMIC1_JD 5 ILMIC1-R 22 ILINE_OUTL 23 GND 24 ISPK_JD 25 ILINE_OUTR Table 4-14: Audio Jack Pinouts (AUDIO1) 4.3.2 DIO c o n n e c to r (DIO1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DIN1 2 DOUT1 3 DIN2 4 DOUT2 5 DIN3 6 DOUT3 7 DIN4 8 DOUT4 9 VCC5 Table 4-15: DIO connector Pinouts (DIO1) 4.3.3 DVI Co n n e c to r (DVI_1) PIN NO. DESCRIPTION PIN NO.
PAGE 62
TANK-820-H61 Em be d d e d S ys te m C3 BB-2 C5 GND C4 HSYNC-2 Table 4-16: DVI Connector Pinouts (DVI_1) 4.3.4 Eth e rn e t a n d US B2.0 Co n n e c to rs (US BLAN1) PIN NO. DESCRIPTION PIN NO.
PAGE 63
TANK-820-H61 Em be d d e d S ys te m Table 4-18: Ethernet and USB2.0 Connectors Pinouts (USBLAN2) 4.3.6 P owe r Co n n e c to r (P WR2) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 2 GND 3 VCC 4 GND 5 GND Table 4-19: Power Connector Pinouts (PWR2) 4.3.7 P owe r Co n n e c to r (P WR1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 ACCON 2 VCC 3 GND Table 4-20: Power Connector Pinouts (PWR1) 4.3.8 RS -232 S e ria l P o rt Co n n e c to r (COM1) PIN NO. DESCRIPTION PIN NO.
PAGE 64
TANK-820-H61 Em be d d e d S ys te m 3 INTX3 4 INDTR3 5 GND 6 INDSR3 7 INRTS3 8 INCTS3 9 INRI3 10 INDCD4 11 INRX4 12 INTX4 13 INDTR4 14 GND 15 INDSR4 16 INRTS4 17 INCTS4 18 INRI4 Table 4-22: RS-232 Serial Port Connector Pinouts (COM2) 4.3.10 RS -232 S e ria l P o rt Co n n e c to r (COM7) PIN NO. DESCRIPTION PIN NO.
PAGE 65
TANK-820-H61 Em be d d e d S ys te m A3 N/A A4 ITXD5485+ A5 N/A A6 IRXD5485# A7 N/A A8 IRXD5485+ B1 N/A B2 ITXD6485# B3 N/A B4 ITXD6485+ B5 N/A B6 IRXD6485# B7 N/A B8 IRXD6485+ Table 4-25: RS-422/485 Serial Port Connectors Pinouts (LANCOM3) 4.3.13 US B 3.0 Co n n e c to rs (US B3_12) PIN NO. DESCRIPTION PIN NO.
PAGE 66
TANK-820-H61 Em be d d e d S ys te m Table 4-27: VGA Connector Pinouts (VGA1) 4.4 J u m p e r S e ttin g s The jumpers on the system motherboard are listed in Table 4-28. Co n n e c to r Typ e La b e l Clear CMOS setup 3-pin header J_CMOS2 Table 4-28: Jumper 4.4.
PAGE 67
TANK-820-H61 Em be d d e d S ys te m Ch a p te r 5 5 BIOS P a g e 54
PAGE 68
TANK-820-H61 Em be d d e d S ys te m 5.1 In tro d u c tio n The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice. 5.1.1 Sta rtin g S e tu p The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1.
PAGE 69
TANK-820-H61 Em be d d e d S ys te m Ke y Fu n c tio n - Decrease the numeric value or make changes Page Up key Increase the numeric value or make changes Page Dn key Decrease the numeric value or make changes Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu F1 General help, only for Status Page Setup Menu and Option Page Setup Menu F2 Previous values F3 Load optimized defaults F4 Save change
PAGE 70
TANK-820-H61 Em be d d e d S ys te m  Save & Exit – Selects exit options and loads default settings. The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above.
PAGE 71
TANK-820-H61 Em be d d e d S ys te m 5.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor American Megatrends Set the Date. Use Tab to Core Version 4.6.5.3-0.19 switch between Data Compliency UEFI 2.3; PI 1.2 elements. Project Version SE21AR33.
PAGE 72
TANK-820-H61 Em be d d e d S ys te m The Main menu lists the following system details:  BIOS Information  Processor Information  Memory Information  PCH Information  SPI Clock Frequency The Main menu has two user configurable fields:  S ys te m Da te [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year.  S ys te m Tim e [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.
PAGE 73
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 74
TANK-820-H61 Em be d d e d S ys te m  ACP I S le e p Sta te [S 1 (CP U Sto p Clo c k)] Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.  S1 (CPU Stop DEFAULT The system enters S1(POS) sleep state. The system appears off. The CPU is stopped; RAM is Clock) refreshed; the system is running in a low power mode.  S3 (Suspend The caches are flushed and the CPU is powered to off. Power to the RAM is maintained.
PAGE 75
TANK-820-H61 Em be d d e d S ys te m  Wa ke S ys te m with Fixe d Tim e [Dis a b le d ] Use the Wake System with Fixed Time option to specify the time the system should be roused from a suspended state.
PAGE 76
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Configuration Security Device Support Enables or Disables BIOS support for security device. O.S. will not Current Status Information show Security Device. NO Security Device Found TCG EFI protocol and INT1A interface will not be available. ---------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
PAGE 77
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Configuration > CPU Information ---------------------: Select Screen Hyper-threading [Enabled] ↑ ↓: Select Item Intel Virtualization Technology [Disabled] Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 78
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Information Genuine Intel(R) CPU @ 2.
PAGE 79
TANK-820-H61 Em be d d e d S ys te m  L2 Cache: Lists the amount of storage space on the L2 cache.  L3 Cache: Lists the amount of storage space on the L3 cache. 5.3.5 S ATA Co n fig u ra tio n Use the SATA Configuration menu (BIOS Menu 8) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced SATA Controller(s) SATA Mode Selection [Enabled] [IDE] Enable or disable SATA Device.
PAGE 80
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Intel Trusted Execution Technology Configuration Intel TXT support only can be enabled/disabled if SMX is enabled. VT and VT-d support must also be enabled prior to TXT. Secure Mode Extensons (SMX) Enabled Intel TXT(LT) Support [Disabled] --------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
PAGE 81
TANK-820-H61 Em be d d e d S ys te m  US B De vic e s The USB Devices field lists the USB devices that are enabled on the system  Le g a c y US B S u p p o rt [En a b le d ] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded.
PAGE 82
TANK-820-H61 Em be d d e d S ys te m 5.3.8.1 S e ria l P o rt n Co n fig u ra tio n Use the Serial Port n Configuration menu (BIOS Menu 12) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Serial Port n Configuration Serial Port Device Settings Enable or Disable Serial Port (COM) [Enabled] IO=2C0h; IRQ=11 --------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
PAGE 83
TANK-820-H61 Em be d d e d S ys te m    IO=2C0h; Serial Port I/O port address is 2C0h and the interrupt IRQ=10, 11 address is IRQ10, 11 IO=2C8h; Serial Port I/O port address is 2C8h and the interrupt IRQ=10, 11 address is IRQ10, 11 De vic e Mo d e [RS 232] The Device Mode shows Serial Port 7 provides RS-232 communications. 5.3.8.1.2 S e ria l P o rt 8 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.
PAGE 84
TANK-820-H61 Em be d d e d S ys te m 5.3.9 F81866 S u pe r IO Co nfig u ra tio n Use the F81866 Super IO Configuration menu (BIOS Menu 13) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 85
TANK-820-H61 Em be d d e d S ys te m 5.3.9.1.1 S e ria l P o rt 1 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 86
TANK-820-H61 Em be d d e d S ys te m  Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 87
TANK-820-H61 Em be d d e d S ys te m     IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=10 address is IRQ10 IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=10, 11 address is IRQ10, 11 IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=10, 11 address is IRQ10, 11 De vic e Mo d e [RS 232] The Device Mode shows Serial Port 3 provides RS-232 communications. 5.3.9.1.
PAGE 88
TANK-820-H61 Em be d d e d S ys te m  De vic e Mo d e [RS 232] The Device Mode shows Serial Port 4 provides RS-232 communications. 5.3.9.1.5 S e ria l P o rt 5 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.
PAGE 89
TANK-820-H61 Em be d d e d S ys te m 5.3.9.1.6 S e ria l P o rt 6 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 90
TANK-820-H61 Em be d d e d S ys te m 5.3.10 F81866 H/W Mo n ito r The F8186 H/W Monitor menu (BIOS Menu 15) shows the operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select > Smart Fan Mode Configuration CPU Temperature System Temperature Fan1 Speed Fan2 Speed :+62 C :+37 C :2325 RPM :N/A --------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
PAGE 91
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Smart Fan Mode Configuration Smart Fan control Temperature of Off Temperature of Start Start PWM Slope(Duty Cycle) Smart Fan Mode Select [Auto PWM Mode] 75 80 30 [4] -------------------: Select Screen ↑ ↓: Select Item Enter Select System Smart Fan control [Auto Duty-Cycle Mode] +/-: Change Opt.
PAGE 92
TANK-820-H61 Em be d d e d S ys te m the CPU is at a very high temperature and therefore cause the system to be damaged. The Temperature of Off option can only be set if the Smart Fan control option is set to Auto PWM Mode. When the CPU Temperature is lower than Temperature of Off, the fan will be rotate at lowest speed. To set a value, select the Temperature of Off option and enter a decimal number between 0 and 127. The temperature range is specified below.
PAGE 93
TANK-820-H61 Em be d d e d S ys te m the Start PWM option and enter a decimal number between 0 and 100. The temperature range is specified below.   Minimum Value: 0  Maximum Value: 100 S lo p e (Du ty Cyc le ) [4 (P WM)] The Slope (Duty Cycle) option can only be set if the Smart Fan control option is set to Auto PWM Mode. Use the Slope (Duty Cycle) option to select the linear rate at which the PWM mode increases with respect to an increase in temperature.
PAGE 94
TANK-820-H61 Em be d d e d S ys te m  Firs t Bo u n d a ry Te m p e ra tu re Use the + or – key to change the First Boundary Temperature value. Enter a decimal number between 1 and 100.  S e c o n d Bo u n d a ry Te m p e ra tu re Use the + or – key to change the Second Boundary Temperature value. Enter a decimal number between 1 and 100.  Th ird Bo u n d a ry Te m p e ra tu re Use the + or – key to change the Third Boundary Temperature value. Enter a decimal number between 1 and 100.
PAGE 95
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 96
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced COM1 Console Redirection Settings Terminal Type Bits per second Data Bits Parity Stop Bits [ANSI] [115200] [8] [None] [1] Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.
PAGE 97
TANK-820-H61 Em be d d e d S ys te m   57600  115200 The transmission speed is 57600 DEFAULT The transmission speed is 115200 Da ta Bits [8] Use the Data Bits option to specify the number of data bits.   7  8 Sets the data bits at 7. DEFAULT Sets the data bits at 8. P a rity [No n e ] Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors.  None  Even DEFAULT No parity bit is sent with the data bits.
PAGE 98
TANK-820-H61 Em be d d e d S ys te m 5.3.12 iEi Fe a tu re Use the iEi Feature menu (BIOS Menu 19) to configure the iEi features. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes. Please install Auto Recovery API service before enabling this function. --------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
PAGE 99
TANK-820-H61 Em be d d e d S ys te m 5.4 Ch ips e t Use the Chipset menu (BIOS Menu 20) to access the Northbridge and Southbridge configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 100
TANK-820-H61 Em be d d e d S ys te m 5.4.1 P CH-IO Co n fig u ra tio n Use the PCH-IO Configuration menu (BIOS Menu 21) to configure the PCH parameters. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset PCH-IO Configuration High Definition Audio Controller. Auto Power Button Status [Enabled(AT)] High Definition Audio Controller [Enabled] --------------------- : Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 101
TANK-820-H61 Em be d d e d S ys te m 5.4.2 S ys te m Ag e n t (S A) Co n fig u ra tio n Use the System Agent (SA) Configuration menu (BIOS Menu 22) to configure the graphics setting and memory setting. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 102
TANK-820-H61 Em be d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Graphics Configuration Select DVMT 5.0 Pre-Allocated (Fixed) DVMT Pre-Allocated [256M] Graphics Memory size DVMT Total Gfx Mem [MAX] used by the Internal Graphics Device. Internal Graphics [Auto] ---------------------: Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.14.1219.
PAGE 103
TANK-820-H61 Em be d d e d S ys te m  In te rn a l Gra p h ic s [Au to ] Use the Internal Graphics option to keep IGD enabled based on the setup option. The following options are available:  Auto  Disabled  Enabled Default 5.5 Bo o t Use the Boot menu (BIOS Menu 24) to configure system boot options. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 104
TANK-820-H61 Em be d d e d S ys te m  On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.  Does not enable the keyboard Number Lock Off automatically. To use the 10-keys on the keyboard, press the Number Lock key located on the upper left-hand corner of the 10-key pad.
PAGE 105
TANK-820-H61 Em be d d e d S ys te m  Sets display mode to current. Keep Current  UEFI Bo o t [Dis a b le d ] Use the UEFI Boot option to enable or disable to boot from the UEFI devices.  Enabled  Disabled Boot from UEFI devices is enabled. DEFAULT Boot from UEFI devices is disabled. 5.6 S e c u rity Use the Security menu (BIOS Menu 25) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 106
TANK-820-H61 Em be d d e d S ys te m 5.7 Exit Use the Exit menu (BIOS Menu 26) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Exit the system after saving the changes.
PAGE 107
TANK-820-H61 Em be d d e d S ys te m  S a ve a s Us e r De fa u lts Use the Save as User Defaults option to save the changes done so far as user defaults.  Re s to re Us e r De fa u lts Use the Restore User Defaults option to restore the user defaults to all the setup options.
PAGE 108
TANK-820-H61 Em be d d e d S ys te m Ap p e n d ix A A On e Ke y Re c o ve ry P a g e 95
PAGE 109
TANK-820-H61 Em be d d e d S ys te m A.1 On e Ke y Re c o ve ry In tro d u c tio n The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 110
TANK-820-H61 Em be d d e d S ys te m After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section A.5. NOTE: The initial setup procedures for Linux system are described in Section A.3. A.1.1 S ys te m Re q u ire m e n t NOTE: The recovery CD can only be used with IEI products.
PAGE 111
TANK-820-H61 Em be d d e d S ys te m partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. A.1.
PAGE 112
TANK-820-H61 Em be d d e d S ys te m o o o o o o o Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. A.2 S e tu p P ro c e d u re fo r Win d ows Prior to using the recovery tool to backup or restore Windows system, a few setup procedures are required. S te p 1: Hardware and BIOS setup (see Section A.2.1) S te p 2: Create partitions (see Section A.2.
PAGE 113
TANK-820-H61 Em be d d e d S ys te m A.2.1 Ha rdwa re a n d BIOS S e tu p S te p 1: Make sure the system is powered off and unplugged. S te p 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended. S te p 3: Connect an optical disk drive to the system and insert the recovery CD. S te p 4: Turn on the system. S te p 5: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 114
TANK-820-H61 Em be d d e d S ys te m Figure A-2: Launching the Recovery Tool S te p 3: The recovery tool setup menu is shown as below. Figure A-3: Recovery Tool Setup Menu S te p 4: Press <6> then .
PAGE 115
TANK-820-H61 Em be d d e d S ys te m Figure A-4: Command Mode S te p 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 116
TANK-820-H61 Em be d d e d S ys te m Figure A-5: Partition Creation Commands P a g e 103
PAGE 117
TANK-820-H61 Em be d d e d S ys te m NOTE: Use the following commands to check if the partitions were created successfully. S te p 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build-up Recovery Partition. A.2.3 In s ta ll Op e ra tin g S ys te m , Drive rs a n d Ap p lic a tio n s Install the operating system onto the unlabelled partition.
PAGE 118
TANK-820-H61 Em be d d e d S ys te m A.2.4 Bu ild -u p Re c o ve ry P a rtitio n S te p 1: Put the recover CD in the optical drive. S te p 2: Start the system. S te p 3: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure A-6: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <2> then .
PAGE 119
TANK-820-H61 Em be d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section A.2.2 is hidden and the recovery tool is saved in this partition. Figure A-8: Building the Recovery Partition S te p 6: After completing the system configuration, press any key in the following window to reboot the system.
PAGE 120
TANK-820-H61 Em be d d e d S ys te m A.2.5 Cre a te Fa c to ry De fa u lt Im a g e NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. S te p 1: Turn on the system. When the following screen displays (Figure A-10), press the key to access the recovery tool.
PAGE 121
TANK-820-H61 Em be d d e d S ys te m Figure A-12: About Symantec Ghost Window S te p 4: Use mouse to navigate to the option shown below (Figure A-13). Figure A-13: Symantec Ghost Path S te p 5: P a g e 108 Select the local source drive (Drive 1) as shown in Figure A-14. Then click OK.
PAGE 122
TANK-820-H61 Em be d d e d S ys te m Figure A-14: Select a Local Source Drive S te p 6: Select a source partition (Part 1) from basic drive as shown in Figure A-15. Then click OK. Figure A-15: Select a Source Partition from Basic Drive S te p 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure A-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 123
TANK-820-H61 Em be d d e d S ys te m Figure A-16: File Name to Copy Image to S te p 8: When the Compress Image screen in Figure A-17 prompts, click High to make the image file smaller.
PAGE 124
TANK-820-H61 Em be d d e d S ys te m S te p 9: The Proceed with partition image creation window appears, click Yes to continue. Figure A-18: Image Creation Confirmation S te p 10: The Symantec Ghost starts to create the factory default image (Figure A-19). Figure A-19: Image Creation Process S te p 11: When the image creation completes, a screen prompts as shown in Figure A-20. Click Continue and close the Ghost window to exit the program.
PAGE 125
TANK-820-H61 Em be d d e d S ys te m S te p 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure A-21: Press Any Key to Continue A.3 Au to Re c o ve ry S e tu p P ro c e d u re The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 126
TANK-820-H61 Em be d d e d S ys te m Figure A-22: Auto Recovery Utility S te p 3: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure A-23: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <4> then .
PAGE 127
TANK-820-H61 Em be d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition. In this process the partition created for recovery files in Section A.2.2 is hidden and the auto recovery tool is saved in this partition. Figure A-25: Building the Auto Recovery Partition S te p 6: After completing the system configuration, the following message prompts to confirm whether to create a factory default image.
PAGE 128
TANK-820-H61 Em be d d e d S ys te m S te p 7: The Symantec Ghost starts to create the factory default image (Figure A-27). Figure A-27: Image Creation Complete S te p 8: After completing the system configuration, press any key in the following window to restart the system. Figure A-28: Press any key to continue S te p 9: Eject the One Key Recovery CD and restart the system. S te p 10: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 129
TANK-820-H61 Em be d d e d S ys te m Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit iEi Feature  Auto Recovery Function [Enabled] Recover from PXE [Disabled]  ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 27: IEI Feature S te p 12: Save changes and restart the system.
PAGE 130
TANK-820-H61 Em be d d e d S ys te m Install Linux operating system. Make sure to install GRUB (v0.97 or earlier) S te p 2: MBR type and Ext3 partition type. Leave enough space on the hard drive to create the recover partition later. NOTE: If the Linux OS is not installed with GRUB (v0.97 or earlier) and Ext3, the Symantec Ghost may not function properly.
PAGE 131
TANK-820-H61 Em be d d e d S ys te m DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>exit system32>format N: /fs:ntfs /q /v:Recovery /y system32>exit S te p 4: Build-up recovery partition. Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient. When the recovery tool setup menu appears, type <3> and press (Figure A-30). The Symantec Ghost window appears and starts configuring the system to build-up a recovery partition.
PAGE 132
TANK-820-H61 Em be d d e d S ys te m Figure A-31: Access menu.lst in Linux (Text Mode) S te p 6: Modify the menu.lst as shown below. S te p 7: The recovery tool menu appears. (Figure A-32) Figure A-32: Recovery Tool Menu S te p 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section A.2.5 to create a factory default image.
PAGE 133
TANK-820-H61 Em be d d e d S ys te m A.5 Re c o ve ry To o l Fu n c tio n s After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section A.3 has been completed and the auto recovery function is enabled, the system will automatically restore from the factory default image without pressing the F3 key. The recovery tool main menu is shown below.
PAGE 134
TANK-820-H61 Em be d d e d S ys te m WARNING: All data in the system will be deleted during the system recovery. Please backup the system files before restoring the system (either Factory Restore or Restore Backup). A.5.1 Fa c to ry Re s to re To restore the factory default image, please follow the steps below. S te p 1: Type <1> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.
PAGE 135
TANK-820-H61 Em be d d e d S ys te m Figure A-35: Recovery Complete Window A.5.2 Ba c ku p S ys te m To backup the system, please follow the steps below. S te p 1: Type <2> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure A-36: Backup System S te p 3: The screen is shown as in Figure A-37 when system backup is completed.
PAGE 136
TANK-820-H61 Em be d d e d S ys te m Figure A-37: System Backup Complete Window A.5.3 Re s to re Yo u r La s t Ba c ku p To restore the last system backup, please follow the steps below. S te p 1: Type <3> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure A-38: Restore Backup S te p 3: The screen is shown as in Figure A-39 when backup recovery is completed. Press any key to reboot the system.
PAGE 137
TANK-820-H61 Em be d d e d S ys te m Figure A-39: Restore System Backup Complete Window A.5.4 Ma n u a l To restore the last system backup, please follow the steps below. S te p 1: Type <4> and press in the main menu. S te p 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure A-40: Symantec Ghost Window S te p 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 138
TANK-820-H61 Em be d d e d S ys te m A.6 Re s to re S ys te m s fro m a Lin u x S e rve r thro u g h LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 139
TANK-820-H61 Em be d d e d S ys te m A.6.1 Co n fig u re DHCP S e rve r S e ttin g s S te p 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) S te p 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.
PAGE 140
TANK-820-H61 Em be d d e d S ys te m filename “pxelinux.0”; A.6.2 Co n fig u re TFTP S e ttin g s S te p 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) S te p 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 141
TANK-820-H61 Em be d d e d S ys te m Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp A.6.3 Co n fig u re On e Ke y Re c o ve ry S e rve r S e ttin g s S te p 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). S te p 2: Extract the recovery package to /. #cp RecoveryR10.tar.
PAGE 142
TANK-820-H61 Em be d d e d S ys te m A.6.4 Sta rt th e DHCP, TFTP a n d HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart A.6.5 Cre a te S ha re d Dire c to ry S te p 1: Install the samba. #yum install samba S te p 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 143
TANK-820-H61 Em be d d e d S ys te m Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 S te p 4: Edit “/etc/samba/smb.conf” for your environment. For example: S te p 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer A.6.6 S e tu p a Clie n t S ys te m fo r Au to Re c o ve ry S te p 1: Configure the following BIOS options of the client system.
PAGE 144
TANK-820-H61 Em be d d e d S ys te m S te p 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1  remain the default setting to boot from the original OS. Boot Option #2  select the boot from LAN option. S te p 3: Save changes and exit BIOS menu. Exit  Save Changes and Exit S te p 4: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD.
PAGE 145
TANK-820-H61 Em be d d e d S ys te m NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them.
PAGE 146
TANK-820-H61 Em be d d e d S ys te m A.7 Oth e r In fo rm a tio n A.7.1 Us in g AHCI Mo d e o r ALi M5283 / VIA VT6421A Co n tro lle r When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery. Please follow the steps below to install the SATA RAID/AHCI driver. S te p 1: Copy the SATA RAID/AHCI driver to a floppy disk and insert the floppy disk into a USB floppy disk drive.
PAGE 147
TANK-820-H61 Em be d d e d S ys te m S te p 5: When the following window appears, press ~~to select “Specify Additional Device”. S te p 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD.~~
~~PAGE 148~~
TANK-820-H61 Em be d d e d S ys te m After pressing , the system will get into the recovery tool setup menu. S te p 7: Continue to follow the setup procedure from Step 4 in Section A.2.2 Create Partitions to finish the whole setup process.Step0: A.7.2 S ys te m Me m o ry Re q u ire m e n t To be able to access the recovery tool by pressing while booting up the system, please make sure to have enough system memory. The minimum memory requirement is listed below.
~~PAGE 149~~
~~TANK-820-H61 Em be d d e d S ys te m Ap p e n d ix B B S a fe ty P re c a u tio n s P a g e 136~~
~~PAGE 150~~
TANK-820-H61 Em be d d e d S ys te m B.1 S a fe ty P re c a u tio n s WARNING: The precautions outlined in this appendix should be strictly followed. Failure to follow these precautions may result in permanent damage to the TANK-820-H61. Please follow the safety precautions outlined in the sections that follow: B.1.1 Ge n e ra l S a fe ty P re c a u tio n s Please ensure the following safety precautions are adhered to at all times.
~~PAGE 151~~
TANK-820-H61 Em be d d e d S ys te m Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TANK-820-H61. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the TANK-820-H61 is opened and any of the electrical components are handled, the following anti-static precautions are strictly adhered to.  Wear an anti-static wristband: Wearing a simple anti-static wristband can help to prevent ESD from damaging any electrical component.
~~PAGE 152~~
TANK-820-H61 Em be d d e d S ys te m monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your display products, please follow the guidance of your local authority, or ask the shop where you purchased the product. The mark on electrical and electronic products only applies to the current European Union Member States. Please follow the national guidelines for electrical and electronic product disposal. B.
~~PAGE 153~~
TANK-820-H61 Em be d d e d S ys te m  Vacuum cleaner – Using a vacuum specifically designed for computers is one of the best methods of cleaning the TANK-820-H61. Dust and dirt can restrict the airflow in the TANK-820-H61 and cause its circuitry to corrode.  Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas.  Foam swabs - Whenever possible, it is best to use lint free swabs such as foam swabs for cleaning.
~~PAGE 154~~
~~TANK-820-H61 Em be d d e d S ys te m Ap p e n d ix C C Ha za rd o u s Ma te ria ls Dis c lo s u re P a g e 141~~
~~PAGE 155~~
TANK-820-H61 Em be d d e d S ys te m C.1 Ha za rd o u s Ma te ria ls Dis c lo s u re Ta ble for IP B P ro d u c ts Ce rtifie d a s Ro HS Co m p lia n t Un d e r 2002/95/EC With o u t Me rc u ry The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 156~~
TANK-820-H61 Em be d d e d S ys te m P a rt Na m e To xic o r Ha za rd o u s S u b s ta n c e s a n d Ele m e n ts Le a d Me rc u ry Ca d m iu m He xa va le n t P o lyb ro m in a te d P o lyb ro m in a te d (P b ) (Hg ) (Cd ) Ch ro m iu m Bip h e n yls Dip h e n yl (CR(VI)) (P BB) Eth e rs (P BDE) Ho u s in g X O O O O X Dis p la y X O O O O X P rin te d Circ u it X O O O O X X O O O O O X O O O O X Fa n As s e m b ly X O O O O X P o we r S u p p ly X
~~PAGE 157~~
TANK-820-H61 Em be d d e d S ys te m 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯 (P b ) (Hg ) (Cd ) (CR(VI)) (P BB) 醚 (P BDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T