SRM Series/SRM-KIT Series Monitor SRM Series LCD Monitor IEI Technology Corp. MODEL: SRM Series/SRM-KIT Series High Brightness Industrial Monitor 9-36 V DC Input, VGA/DVI-D, Auto-Dimming, Touch Screen, RoHS Compliance, IP 65 Protection User Manual Page I Rev. 2.
SRM Series/SRM-KIT Series Monitor Revision Date Version Changes 8 November, 2011 2.02 Updated Section 5.4.6: RS-232 Touch Panel Connector 15 December, 2010 2.01 Modified AV-6600 AD board information Modified Chapter 6 OSD Controls Updated Chapter 7 Software Drivers 27 August, 2010 2.00 Updated for SRM-121/150-R20 and SRM-KIT-R20 September 2008 1.11 Added SRM-121XA/XMA models information May 2007 1.
SRM Series/SRM-KIT Series Monitor Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
SRM Series/SRM-KIT Series Monitor Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.1.1 Standard Features .............................................................................................. 2 1.1.2 SRM Series Industrial Monitor Applications .....................................
SRM Series/SRM-KIT Series Monitor 2.3.4 Monitor Arm or Stand Mounting...................................................................... 19 3 LCD AND TOUCH PANEL SPECIFICATIONS ..................................................... 20 3.1 LCD SPECIFICATIONS ............................................................................................... 21 3.1.1 LCD Overview ................................................................................................. 21 3.1.
SRM Series/SRM-KIT Series Monitor 5.5.2 Cabinet and Rack Installation ......................................................................... 45 5.5.3 Wall Mounting.................................................................................................. 47 5.5.4 Monitor Stand Installation ............................................................................... 51 5.5.5 Monitor Arm Installation .................................................................................
SRM Series/SRM-KIT Series Monitor B.1 ROHS COMPLIANT .................................................................................................. 79 B.2 IP 65 COMPLIANT FRONT PANEL ............................................................................. 79 C SMARTOSD ................................................................................................................ 80 C.1 IEI SMARTOSD QUICK INSTALLATION GUIDE ......................................................... 81 C.
SRM Series/SRM-KIT Series Monitor List of Figures Figure 1-1: SRM and SRM-KIT Series LCD Monitor ....................................................................2 Figure 1-2: SRM Series Front View ...............................................................................................5 Figure 1-3: SRM-KIT Series Front View ........................................................................................6 Figure 1-4: SRM Series Rear View ....................................................
SRM Series/SRM-KIT Series Monitor Figure 5-16: Monitor Arm Mounting............................................................................................53 Figure 6-1: OSD Control Buttons for All Models .......................................................................55 Figure 6-2: Main Display Features ..............................................................................................58 Figure 6-3: Color Options ........................................................................
SRM Series/SRM-KIT Series Monitor List of Tables Table 1-1: SRM-121 Model Variants ..............................................................................................4 Table 1-2: SRM-150 Model Variants ..............................................................................................4 Table 1-3: SRM Series Specifications.........................................................................................11 Table 2-1: SRM Series Mounting Kits ......................................
SRM Series/SRM-KIT Series Monitor Chapter 1 1 Introduction Page 1
SRM Series/SRM-KIT Series Monitor 1.1 Overview Figure 1-1: SRM and SRM-KIT Series LCD Monitor The SRM series industrial monitor is the latest member of IEI’s line of sophisticated LCD designs, and it has been improved to be RoHS compliant. The SRM series is designed to fit industrial automation, or any other applications that require minimum installation space and flexible configuration.
SRM Series/SRM-KIT Series Monitor Wide range operating temperature Wide viewing angle High contrast ratio Advanced thermal and air-flow design 9 ~ 36V DC power input for mobile application Supports panel, rack, wall, stand and arm mounting RS-232 and USB interface touch panel 1.1.2 SRM Series Industrial Monitor Applications The SRM series industrial monitor is designed for rigorous industrial environments where it may be exposed to both heat and moisture.
SRM Series/SRM-KIT Series Monitor 1.1.3 Model Variations 1.1.3.1 SRM-121 Model Variations The SRM-121 has eight models variations listed in Table 1-1. Model Number LCD Size Resolution 9~36V Power Touch Screen SRM-121GS/R-R20 12.1” 800 x 600 No RS-232 and USB SRM-121GMS/R-R20 12.1” 800 x 600 Yes RS-232 and USB SRM-121XA/R-R20 12.1” 1024 x 768 No RS-232 and USB SRM-121XMA/R-R20 12.1” 1024 x 768 Yes RS-232 and USB SRM-KIT121G-R20 12.1” 800 x 600 No No SRM-KIT121GM-R20 12.
SRM Series/SRM-KIT Series Monitor 1.2 External Overview The SRM series industrial monitors are durable devices that can be used in harsh industrial environments. The following sections describe the physical layout of the SRM series industrial monitors. 1.2.1 SRM Series Front View The front of the SRM series industrial monitor is a flat panel TFT LCD screen surrounded by an aluminum frame.
SRM Series/SRM-KIT Series Monitor 1.2.2 SRM-KIT Series Front View The front of the SRM-KIT series monitor is a flat panel TFT LCD screen attached to a metal chassis. Figure 1-2 shows a typical SRM-KIT front view. Figure 1-3: SRM-KIT Series Front View 1.2.3 SRM Series Rear View The rear panel features fan ventilation holes and four retention screw holes that support a wall-mounting bracket. The retention screw holes are circled in Figure 1-4.
SRM Series/SRM-KIT Series Monitor 1.2.4 SRM-KIT Series Rear View The rear of the SRM-KIT series monitor is a metal chassis. An on screen display (OSD) control button panel is located vertically on the left side of the chassis with the following control buttons: LCD On/Off Auto Left Right Menu The OSD panel also has one auto-dimming sensor, one power LED and one autodimming LED. Refer to Chapter 6 for a complete description of OSD panel.
SRM Series/SRM-KIT Series Monitor 1.2.5 Top View The top view provides access to retention screws that secure the back cover to the chassis. The retention screw holes are circled in Figure 1-6 below. Figure 1-6: Top View 1.2.6 Bottom View The bottom view provides access to retention screws that secure the back cover to the chassis. The retention screw holes are circled in Figure 1-7 below. Figure 1-7: Bottom View 1.2.
SRM Series/SRM-KIT Series Monitor Figure 1-8: Side View 1.2.8 SRM-KIT Series I/O Panel The I/O panel of the SRM-KIT Series shown in Figure 1-8 has the following interfaces.
SRM Series/SRM-KIT Series Monitor 1.2.9 SRM Series Frame An aluminum frame surrounds the SRM series LCD monitor. This aluminum frame has small screw holes that are used to attach the LCD monitor to a rack mount kit for mounting into a rack or cabinet. The screw holes on SRM-121 and SRM-150 are circled in Figure 1-10 and Figure 1-11.
SRM Series/SRM-KIT Series Monitor 1.3 Series Specifications Table 1-3 shows the SRM Series specifications. Model SRM-121 SRM-121XA/XMA SRM-150 LCD Size 12.1” 12.1” 15” Input Interface Analog VGA and DVI-D Resolution 800 x 600 Brightness 1000 cd/m2 800 cd/m2 Contrast 700:1 600:1 Display Color 262K (6 bit/color) or 16.7M (8 bit/color) Pixel Pitch 0.
SRM Series/SRM-KIT Series Monitor 1.4 Certifications All SRM series industrial monitor models comply with the following international standards: RoHS IP 65 For a more detailed description of these standards, please refer to Sections B.1 and B.2.
SRM Series/SRM-KIT Series Monitor Chapter 2 2 Mechanical Overview Page 13
SRM Series/SRM-KIT Series Monitor 2.1 Physical Dimensions The following sections describe the physical dimensions for the SRM-121, SRM-150 and SRM-KIT industrial monitor. 2.1.1 SRM-121 Physical Dimensions The physical dimensions of the SRM-121 are shown in Figure 2-1.
SRM Series/SRM-KIT Series Monitor 2.1.2 SRM-150 Physical Dimensions The physical dimensions of the SRM-150 are shown in Figure 2-2.
SRM Series/SRM-KIT Series Monitor 2.1.3 SRM-KIT121 Physical Dimensions The physical dimensions of the SRM-KIT121 are shown in Figure 2-2.
SRM Series/SRM-KIT Series Monitor 2.1.4 SRM-KIT150 Physical Dimensions The physical dimensions of the SRM-KIT150 are shown in Figure 2-2.
SRM Series/SRM-KIT Series Monitor 2.2 Mounting Kits The following sections describe the various optional mounting kits available for each model of the SRM series industrial monitor. Refer to Section 5.5 for detailed instructions on the different mounting methods for the monitors. Table 2-1 lists the mounting kits available for the SRM series monitor.
SRM Series/SRM-KIT Series Monitor Model Mounting Clamps SRM-121 10 SRM-150 10 Table 2-2: Panel Mounting Clamps 2.3.2 Rack and Cabinet Mounting Each model of the SRM series industrial monitor has a series of holes located on the rear of the front panel for securing the monitor to the rack mounting kit. Table 2-3 lists the number of holes each monitor has to secure the monitor to the rack mounting kit. Model Holes SRM-121 10 SRM-150 12 Table 2-3: Rack Mounting Holes 2.3.
SRM Series/SRM-KIT Series Monitor Chapter 3 3 LCD and Touch Panel Specifications Page 20
SRM Series/SRM-KIT Series Monitor 3.1 LCD Specifications 3.1.1 LCD Overview The SRM series industrial monitors use the following LCD panels. SRM-121: MITSUBISHI AA121SN02 SVGA TFT LCD SRM-150: MITSUBISHI AA150XN08 XGA TFT LCD Detailed specifications for the LCD screens are listed in the following sections. 3.1.2 SRM-121 LCD Specifications Table 3-1 lists the LCD specifications of the SRM-121. Model SRM-121 Size 12.
SRM Series/SRM-KIT Series Monitor Model Power Supply Current for LCD SRM-121 300mA / 450mA Voltage: 540 Vrms Lamp Voltage/Current Current: 12.0 mArms/14.0 mAms (Max.) 1000 Vrms (25°C)/ 1200 Vrms (0°C)/ Starting Lamp Minimum Voltage 1290 Vrms (-20°C) Operating Temperature -10°C ~60°C Operating Humidity 5%~90% RH. Storage Temperature -20°C ~80°C Shock Level (Non-operation) 1470 m/s2 (100G), Waveform 2ms. 9.8 m/s2 (1.
SRM Series/SRM-KIT Series Monitor Model SRM-121XA/XMA View Angle (H/V) 120 / 120 Brightness (cd/m2) 1000 Contrast Ratio 700:1 Response Time (ms) TR: 6 TF: 19 Interface LVDS (6 bit/8 bit) Input Voltage (V) 3.3V Backlight 4 CCFL Power Supply Voltage for LCD 3.3V / 3.6V (Max.) Power Supply Current for LCD 300mA / 450mA Voltage: 540 Vrms Lamp Voltage/Current Current: 13.
SRM Series/SRM-KIT Series Monitor 3.1.4 SRM-150 LCD Specifications Table 3-3 lists the LCD specifications of the SRM-150. Model SRM-150 Size 15” MFR/Model MITSUBISHI AA150XN08 Resolution XGA (1024 x 768) Active Area (mm) 246.0 x 184.5 Pixel Pitch (mm) 0.297 x 0.297 Number of Colors 262K(6 bit/color), 16.7M(8 bit/color) View Angle (H/V) 150 / 110 Brightness (cd/m2) 800 Contrast Ratio 600:1 Response Time (ms) TR: 6 TF: 19 Interface LVDS (6 bit/8 bit) Input Voltage (V) 3.
SRM Series/SRM-KIT Series Monitor Model SRM-150 Operating Humidity 5%~90% RH. Storage Temperature -20°C ~80°C Shock Level (Non-operation) 980 m/s2 (100G), Waveform 2ms. 9.8 m/s2 (1.0G) zero to peak, frequency Vibration Level (Non-operation) range 5-500Hz sweep rate 0.
SRM Series/SRM-KIT Series Monitor 3.2 Optional Touch Panels IEI offers optional touch panels for the SRM series industrial monitors with the following features: Small border customized design All size touch panel design Customized activation force and palm rejection Customized optical characteristics High reliability and durability in the field 3.2.1 Touch Panel Models Table 3-4 lists the SRM series industrial monitors and their associated touch panels.
SRM Series/SRM-KIT Series Monitor 3.2.2 Touch Panel Dimensions Table 3-5 shows the touch panel dimensions in millimeters. Model Dimension Width Length Thick Dimensional Outline: 204 268 2.1 Viewing Area: 188 250 - Active Area: 185 246 - Dimensional Outline: 257.5 333.6 2.9 Viewing Area: 232.1 308.2 - Active Area: 228.1 304.
SRM Series/SRM-KIT Series Monitor 3.2.3 Touch Panel Specifications Table 3-6 lists the touch panel specifications.
SRM Series/SRM-KIT Series Monitor Chapter 4 4 AD Board Page 29
SRM Series/SRM-KIT Series Monitor 4.1 AV-6600 AD Board Overview The AV-6600 AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. The following sections describe the AV-6600 AD board in detail. Figure 4-1: AV-6600 AD Board Overview 4.1.1 AV-6600 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the AV-6600 AD board.
SRM Series/SRM-KIT Series Monitor Auto-dimming connector 6-pin wafer connector CN7 Debug connector 4-pin wafer connector CN9 External OSD and LED indication connector 9-pin wafer connector CN10 Infrared connector 6-pin wafer connector CN8 Inverter interface connector 6-pin wafer connector CN6 LVDS connector 30-pin connector CN5 Power output connector (+12 V) 2-pin wafer connector CN3 Power output connector (+5 V) 2-pin wafer connector CN4 Power input connector 3-pin connector CN2
SRM Series/SRM-KIT Series Monitor 4.1.2 AV-6600 Rear Panel Connectors Table 4-2 lists the rear panel connectors on the AV-6600 AD board.
SRM Series/SRM-KIT Series Monitor Chapter 5 5 Installation Page 33
SRM Series/SRM-KIT Series Monitor 5.1 Installation Precautions When installing the SRM series industrial monitor, please follow the precautions listed below: Read the user manual: The user manual provides a complete description of the SRM series industrial monitor, installation instructions and configuration options. DANGER! Disconnect Power: Power to the monitor must be disconnected when installing the SRM series industrial monitor, or before any attempt is made to access the rear panel.
SRM Series/SRM-KIT Series Monitor 5.2 Unpacking 5.2.1 Packaging When shipped, the SRM series industrial monitor is wrapped in a plastic bag. Two polystyrene ends are placed on either side of the monitor. The monitor is then placed into a first (internal) cardboard box. This box is then sealed and placed into a second (external) cardboard box. The second box is also sealed. A bag containing accessory items is placed underneath the monitor, at the bottom of the internal (first) box. 5.2.
SRM Series/SRM-KIT Series Monitor 5.2.3 Packing List All the monitors in the SRM series are shipped with the following components: Quantity Item 1 36 W AC power adapter 1 AC power cord 1 DVI cable 1 Screw kit 1 VGA cable 1 User manual and driver CD 1 Touch screen driver CD (SRM series only) 1 Touch pen (SRM series only) Image If any of these items are missing or damaged, contact the distributor or sales representative immediately.
SRM Series/SRM-KIT Series Monitor 5.3 Pre-installation Preparation 5.3.1 Tools Before installing the SRM series industrial monitor, make sure the following tools are on hand: Phillips (crosshead) screwdriver: All the retention screws on the system are Phillips screws. Soft working mat: When the SRM series industrial monitor is installed, the screen is placed on the working surface.
SRM Series/SRM-KIT Series Monitor Step 4: Use the jumper(s) to set the correct voltage input. Replace the rear panel. Step 5: Replace all removed screws.Step 0: 5.4 Connectors Table 5-1 lists the external peripheral interface panel connectors for the SRM series industrial monitors.
SRM Series/SRM-KIT Series Monitor 5.4.1 Rear Panel Connectors Overview Figure 5-1: Monitor Rear Panel Connections Figure 5-1 shows all the possible rear panel connectors for the SRM series LCD monitor. The following sections fully describe the rear panel connectors for the SRM series LCD monitor. 5.4.2 VGA Connector Use the rear panel standard 15-pin female VGA connector to connect the monitor to the system graphics interface.
SRM Series/SRM-KIT Series Monitor 5.4.3 DVI-D Connector Use the rear panel standard 24-pin female DVI-D connector to connect the monitor to the system graphics interface. 5.4.4 12V Power Connector Use the rear panel +12V DC jack to connect the monitor to a power source. Figure 5-2: 12V Power Connector 5.4.5 DC Power Connector Use the rear panel 3-pin terminal block DC power connector to connect the monitor to a DC power source.
SRM Series/SRM-KIT Series Monitor 5.4.6 RS-232 Touch Panel Connector Use the rear panel standard RS-232 DB-9 female touch panel connector to connect the monitor to the system graphics interface.
SRM Series/SRM-KIT Series Monitor 5.5 Mounting the SRM Series LCD Monitor The SRM series LCD monitor can be mounted in a panel, cabinet, rack, or wall. The monitor can also be mounted on a monitor arm or stand. The mounting methods are described below. CAUTION: When mounting the monitor take care to tighten the retention screws or bolts until fully secure, but do not over tighten. Over tightening the retention screws or bolts may cause them to become stripped, rendering them useless. 5.5.
SRM Series/SRM-KIT Series Monitor Figure 5-5: Panel Opening Step 3: Slide the monitor through the hole until the metal frame is flushed against the panel (Figure 5-6).
SRM Series/SRM-KIT Series Monitor Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of the monitor, behind the metal frame. Figure 5-7 shows the location of clamp insertion holes on one side of the LCD monitor. Refer to Table 2-2 for the mounting clamps required for each model.
SRM Series/SRM-KIT Series Monitor Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 5-8). Figure 5-8: Panel Mounting Clamp Position 5.5.2 Cabinet and Rack Installation The SRM series provides optional rack mount kits for industrial racks. To mount the SRM series LCD monitor into a cabinet/rack, please follow the steps below.
SRM Series/SRM-KIT Series Monitor Step 4: Secure the rack mount kit to the monitor by inserting and tightening the retention screws (Figure 5-9). Figure 5-9: Secure the Rack Mount Kit Step 5: Slide the monitor with the attached rack mount kit into a rack or cabinet (Figure 5-10).
SRM Series/SRM-KIT Series Monitor Figure 5-10: Install into a Cabinet/Rack Step 6: Once the monitor with the attached cabinet/rack has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 5-10). 5.5.3 Wall Mounting To mount the SRM series industrial monitor onto a wall, please follow the steps below. Step 1: Select a location on the wall for the wall-mounting bracket.
SRM Series/SRM-KIT Series Monitor Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into the four pilot holes and tightening them (Figure 5-11). Figure 5-11: Wall-mounting Bracket Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the four screw holes on the real panel of the monitor and tighten until the screw shank is secured against the rear panel (Figure 5-12).
SRM Series/SRM-KIT Series Monitor Figure 5-12: Monitor Support Screws Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket.
SRM Series/SRM-KIT Series Monitor Step 8: Carefully insert the screws through the holes and gently pull the monitor downwards until the monitor rests securely in the slotted holes (Figure 5-13). Ensure that all four of the mounting screws fit snuggly into their respective slotted holes.
SRM Series/SRM-KIT Series Monitor 5.5.4 Monitor Stand Installation The SRM series industrial monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-14). Figure 5-14: VESA Mounting Holes The monitor stand mounting plate has a matching VESA hole pattern. To mount the SRM series industrial monitor onto a stand, please follow the steps below.
SRM Series/SRM-KIT Series Monitor Step 2: Secure the monitor to the stand with the supplied retention screws (Figure 5-15). Figure 5-15: Monitor Stand Mounting 5.5.5 Monitor Arm Installation The SRM series industrial monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-14). The monitor arm mounting plate has a matching VESA hole pattern.
SRM Series/SRM-KIT Series Monitor Figure 5-16: Monitor Arm Mounting Page 53
SRM Series/SRM-KIT Series Monitor Chapter 6 6 On-Screen-Display (OSD) Controls Page 54
SRM Series/SRM-KIT Series Monitor 6.1 User Mode OSD Structure 6.1.1 OSD Buttons There are several on-screen-display (OSD) control buttons oriented either vertically along the right hand side of the monitor front panel. Figure 6-1 shows a typical arrangement of OSD controls. Figure 6-1: OSD Control Buttons for All Models LCD ON/OFF Button Press this button to turn the LCD monitor on or off. When the LCD monitor is on, the power LED is turned on in green.
SRM Series/SRM-KIT Series Monitor Menu/Enter Button Press this button to open the OSD window. When inside a menu, press this button to confirm the function adjustment or selection of the item. There may be several levels in one item. As you select an item in the menu, the sub-items will be displayed. The OSD control panel also includes one sensor and two LED. Ambient Light Sensor The ambient light sensor detects the brightness of ambient environment when the auto-dimming function is turned on.
SRM Series/SRM-KIT Series Monitor 6.1.2 OSD Menu Structure Table 6-1 shows the OSD menu structure for all models of the SRM series LCD monitor. Level 0 Level 1 Value Main Display Features Menu Brightness 0 to 100 Contrast 0 to 100 Clock 0 to 100 Phase 0 to 100 H. Position 0 to 100 V.
SRM Series/SRM-KIT Series Monitor 6.2 Using the OSD OSD menu options are described below. 6.2.1 Main Display Features Main display features are shown in Figure 6-2. Figure 6-2: Main Display Features The brightness option adjusts the brightness of screen. This function Brightness adjusts the offset value of ADC. Setting this value too high or too low will affect the quality of image. When the auto- dimming function is turned on, the brightness control is not effective.
SRM Series/SRM-KIT Series Monitor 6.2.2 Color Color options are shown in Figure 6-3. Figure 6-3: Color Options The Color menu fine-tunes the palette of color hues for the LCD. 6500k NTSC standard Kelvin 7500k NTSC standard Kelvin 9300k NTSC standard Kelvin User This item allows fine-tuning the balance among Red, Green, and Blue color hues if images look garish or unrealistic.
SRM Series/SRM-KIT Series Monitor 6.2.3 OSD Configurations The OSD configurations are shown in Figure 6-4. Figure 6-4: OSD Configurations Menu OSD Configurations are described below. OSD Time Out Determines how many seconds the OSD screen stays on screen before it disappears when OSD is left unattended. Adjusts the OSD position on the screen. Position 1 is in the upper left OSD Position of the screen, position 2 in the upper right and position 3 in the center.
SRM Series/SRM-KIT Series Monitor 6.2.4 Auto-Dimming Configurations The SRM industrial monitor features an auto-dimming LCD that can automatically adjust the backlight brightness according to the ambient light. If the auto-dimming function is turned on, the backlight turns brighter when the ambient illuminance is high. The backlight dims automatically when the ambient brightness level is low. The SI unit of illuminance is “lux”. Lux measures the intensity of light.
SRM Series/SRM-KIT Series Monitor The Figure 6-5 shows the SRM-121 default linearity of the LCD backlight and ambient light. When the sensor detects the ambient illuminance as 5200 LUX or above, the SRM 40000 35000 25000 30000 20000 15000 5000 10000 4500 4000 3500 2500 3000 2000 1500 100%100%100% 100%100% 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 1000 0% 500 1000 900 800 700 600 500 400 300 200 100 0 0 LCD Brightness (cd/m2) series industrial monitor adjusts the LCD brightness to 100%.
SRM Series/SRM-KIT Series Monitor 30 and the Light Max. to 70. Then, the adjustable LCD brightness range is among 30% to 70%. By doing this, the LCD brightness does not become too bright or too dark if the ambient light reaches the default maximum or minimum value. LUX Max. and LUX Min. The SRM series is an ideal product for outdoor display.
SRM Series/SRM-KIT Series Monitor Chapter 7 7 Software Drivers Page 64
SRM Series/SRM-KIT Series Monitor 7.1 Introduction The touch panel controller enables analog resistive touch panels for four-wire, five-wire & eight-wire models. The controller directly communicates with the PC system through the touch panel communications interface. The controller design is superior in sensitivity, accuracy, and friendly operation. The touch panel driver emulates the left mouse button and the right mouse button functions.
SRM Series/SRM-KIT Series Monitor USB Interface: If the touch screen interface connection is a USB connection, connect the USB connector on the single board computer to the external USB port connector of the SRM Series monitor. 7.3 Touch Panel Driver Installation WARNING: Before the touch screen driver is installed, make sure the system is connected to the monitor with a USB cable or an RS-232 null cable.
SRM Series/SRM-KIT Series Monitor Step 4: Double click the setup icon in Figure 7-1. Step 5: The Welcome screen in Figure 7-2 appears. Figure 7-2: Welcome Screen Step 6: Click Next to continue. Step 7: The license agreement in Figure 7-3 appears. Accept the terms of the agreement by clicking I Agree.
SRM Series/SRM-KIT Series Monitor Step 8: The installation destination screen appears. See Figure 7-4. Click Install. Figure 7-4: Initiate Install Step 9: The installation of the program begins. See Figure 7-5. Figure 7-5: Installation Starts Step 10: When the installation is complete, the complete screen appears. See Figure 7-6. To complete the installation process click Finish.
SRM Series/SRM-KIT Series Monitor Figure 7-6: Finish Installation 7.4 Change the Touch Screen Interface If the touch screen interface must be changed from an RS-232 interface to a USB interface or, from a USB interface to an RS-232 interface, the following steps must be followed. Step 1: Uninstall the touch screen driver Step 2: Remove the interface cable i.e. remove the RS-232 cable or the USB cable Step 3: Install the new cable i.e. install the USB cable or the RS-232 cable.
SRM Series/SRM-KIT Series Monitor Step 3: Locate the PenMount Monitor icon in the bottom left corner of the screen. Figure 7-7: PenMount Monitor Icon Step 4: Click the icon. A pop up menu appears. See Figure 7-8. Figure 7-8: PenMount Monitor Popup Menu Step 5: Click Control Panel in the pop up menu shown in Figure 7-8. Step 6: The configuration screen in Figure 7-9 appears.
SRM Series/SRM-KIT Series Monitor Step 7: Double click the PenMount 6000 icon as shown in Figure 7-9. Step 8: The calibration initiation screen in Figure 7-10 appears. Step 9: Select the Standard Calibration button as shown in Figure 7-10. Figure 7-10: Calibration Initiation Screen Step 10: The calibration screen in is shown. See Figure 7-11. Figure 7-11: Calibration Screen Step 11: Follow the instructions. The user is asked touch the screen at five specified points after which the screen is calibrated.
SRM Series/SRM-KIT Series Monitor Chapter 8 8 Gasket Replacement Page 72
SRM Series/SRM-KIT Series Monitor 8.1 Gasket Replacement A gasket used for a long time may gradually lose its ability to protect the monitor from fluids and vapors; scratches or dirt may also accumulate. It is recommended that the gasket be replaced yearly. NOTE: If the monitor is mounted vertically, first remove it and place it on a flat, level surface with the display screen facing down before changing the gasket. Step 1: Remove the old gasket from the sides of the monitor.
SRM Series/SRM-KIT Series Monitor Appendix A A Safety Precautions Page 74
SRM Series/SRM-KIT Series Monitor WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the SRM Series. A.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: A.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. Follow the electrostatic precautions outlined below whenever the SRM Series is opened.
SRM Series/SRM-KIT Series Monitor A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the SRM Series may result in permanent damage to the SRM Series and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the SRM Series. Dry climates are especially susceptible to ESD.
SRM Series/SRM-KIT Series Monitor The interior of the SRM Series does not require cleaning. Keep fluids away from the SRM Series interior. Be cautious of all small removable components when vacuuming the SRM Series. Turn the SRM Series off before cleaning the SRM Series. Never drop any objects or liquids through the openings of the SRM Series. Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the SRM Series.
SRM Series/SRM-KIT Series Monitor Appendix B B Certifications Page 78
SRM Series/SRM-KIT Series Monitor B.1 RoHS Compliant All models in the SRM LCD monitor series comply with the Restriction of Hazardous Materials (RoHS) Directive. This means that all components used to build the industrial workstations and the workstation itself are RoHS compliant.
SRM Series/SRM-KIT Series Monitor Appendix C C smartOSD Page 80
SRM Series/SRM-KIT Series Monitor C.1 IEI smartOSD Quick Installation Guide IEI smartOSD is a proprietary On-Screen-Display (OSD) software solution from IEI that enables easy, remote monitor setting adjustments in a Windows environment. IEI smartOSD delivers excellent performance and provides more flexibility than the typical OSD hardware solutions when adjusting a monitor.
SRM Series/SRM-KIT Series Monitor Figure 8-2: smartOSD Installer Step 2: Click “Smart OSD” in Figure 8-2. Step 3: The welcome screen shown in Figure 8-3 appears. Figure 8-3: smartOSD Welcome Screen Step 4: Click Next to continue. Step 5: The Folder Select screen in Figure 8-4 appears.
SRM Series/SRM-KIT Series Monitor Figure 8-4: smartOSD Folder Select Screen Step 6: Select the installation folder in Figure 8-4 shown above. Step 7: Click Next to continue. Step 8: The screen in Figure 8-5 appears. Figure 8-5: smartOSD Confirm Installation Step 9: Confirm the installation by clicking Next in the screen above. Step 10: The program starts to install and the progress bar shown in Figure 8-6 appears.
SRM Series/SRM-KIT Series Monitor Figure 8-6: smartOSD Installation Progress Step 11: When the installation is complete the “Complete Installation” screen in Figure 8-7 appears. Figure 8-7: smartOSD Installation Complete Step 12: Click Close in the screen above. Step 13: After quick setup is complete, the IEI smartOSD wizard logo appears on the desktop as shown in the screen below. Step 14: To access the smartOSD, click the smartOSD wizard logo.
SRM Series/SRM-KIT Series Monitor C.4 Software Illustration The table below shows the smartOSD menu structure for all IEI LCD monitors. NOTE: To update the display setting status immediately, push the refresh button on every page To turn the system on, press ALT + P. Item Elements Management Save/Load File Power Management EDID EDID contains basic information about the monitor and its capabilities.
SRM Series/SRM-KIT Series Monitor Display Auto Adjust Phase Clock Color Auto Color User Red Gain User Green Gain User Blue Gain Color Temperature (5000k and 4200k disabled in the SRM Series) Gamma PIP PIP (disabled in the SRM Series) PIP Source Input (disabled in the SRM Series) PIP Size (disabled in the SRM Series) System Monitor Power Control Auto Brightness (disabled in the SRM Series) Main Source Input (S-Video and CVBS disabled) Volume (disabled in the SRM Series) Factory Presets/OSD Lock/OSD Un
SRM Series/SRM-KIT Series Monitor C.4.
SRM Series/SRM-KIT Series Monitor C.4.
SRM Series/SRM-KIT Series Monitor C.4.
SRM Series/SRM-KIT Series Monitor C.4.
SRM Series/SRM-KIT Series Monitor C.4.
SRM Series/SRM-KIT Series Monitor C.4.6 PIP Page NOTE: The functions in the PIP page are only available in the MDM Series and AFOLUX Series monitors.
SRM Series/SRM-KIT Series Monitor C.4.
SRM Series/SRM-KIT Series Monitor C.4.
SRM Series/SRM-KIT Series Monitor C.5 smartOSD FAQ For troubleshooting, please see the steps below: C.5.1 Windows 2000 Installation Failure Installation fails under Windows 2000 and shows the following image: Figure C-9: DLL Missing Solution: Download and install service pack Windows Installer 3.
SRM Series/SRM-KIT Series Monitor C.5.2 Vista Installation Failure Installation fail under Vista while showing following image: Figure C-10: Windows Vista Error Solution: Install SmartOSD.
SRM Series/SRM-KIT Series Monitor C.5.3 Model Failure The Model Fail error message shown below appears. Figure C-12: Firmware Incompatibility Solution: SmartOSD only supports firmware version 2.0 and following versions. C.5.4 DCC Port Failure The DDC port fail error message shown below appears. Figure C-13: DCC Port Failure Solutions: Check VGA or DVI cable Check an IEI monitor is being used Make sure the version is version 2.3 for the AFOLUX/MDM series and version 1.
