SRM-121/SRM-150 LCD Monitor SRM Series LCD Monitor Page I
SRM-121/SRM-150 LCD Monitor Revision Date Version Changes 2008-09 1.11 Added SRM-121XA/XMA models information 2007-05 1.10 - Added safety warning note for monitors used in high temperature areas (pg. v) - AV-5300 AD Board CN25 connector pin 3 voltage changed to +9V~+36V input 2007-01 Page II 1.
SRM-121/SRM-150 LCD Monitor Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
SRM-121/SRM-150 LCD Monitor Manual Conventions WARNING! Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. Warnings are easy to recognize. The word “warning” is written as “WARNING,” both capitalized and bold and is followed by text. The text is the warning message. A warning message is shown below: WARNING: This is an example of a warning message.
SRM-121/SRM-150 LCD Monitor CAUTION: This is an example of a caution message. Failure to adhere to cautions messages may result in permanent damage to the [MODEL NAME]. Please take caution messages seriously. NOTE: These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes. Notes are easy to recognize.
SRM-121/SRM-150 LCD Monitor Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the SRM-121/SRM-150 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the SRM-121/SRM-150 package.
SRM-121/SRM-150 LCD Monitor Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 SRM-121/SRM-150 LCD MONITOR OVERVIEW ...................................................... 2 1.1.1 Standard Features .............................................................................................. 2 1.1.2 SRM Series Industrial Monitor Applications ..................................................... 3 1.1.
SRM-121/SRM-150 LCD Monitor 3 LCD AND TOUCH PANEL SPECIFICATIONS ..................................................... 20 3.1 LCD SPECIFICATIONS .............................................................................................. 21 3.1.1 LCD Overview ................................................................................................. 21 3.1.2 SRM-121 LCD Specifications .......................................................................... 21 3.1.
SRM-121/SRM-150 LCD Monitor 4.4.3 DVI-D Connector............................................................................................. 50 5 INSTALLATION ......................................................................................................... 51 5.1 INSTALLATION PRECAUTIONS ................................................................................... 52 5.2 UNPACKING..............................................................................................................
SRM-121/SRM-150 LCD Monitor 6.2.6 Auto-Dimming Configurations......................................................................... 81 6.2.6.1 Default Settings......................................................................................... 81 6.2.6.2 OSD Control ............................................................................................. 82 6.2.6.3 Changing the Default Settings .................................................................. 83 7 SOFTWARE DRIVERS .............
SRM-121/SRM-150 LCD Monitor List of Figures Figure 1-1: SRM-121/SRM-150 LCD Monitor ................................................................................2 Figure 1-2: Front View ....................................................................................................................6 Figure 1-3: Rear View .....................................................................................................................7 Figure 1-4: Top View...........................................
SRM-121/SRM-150 LCD Monitor Figure 5-5: Panel Opening ...........................................................................................................61 Figure 5-6: Insert the Monitor......................................................................................................61 Figure 5-7: Clamp Insertion Holes ..............................................................................................62 Figure 5-8: Panel Mounting Clamp Position ........................................
SRM-121/SRM-150 LCD Monitor List of Tables Table 1-1: SRM-121 Model Variants ..............................................................................................4 Table 1-2: SRM-150 Model Variants ..............................................................................................5 Table 1-3: SRM Series Specifications.........................................................................................11 Table 2-1: SRM Series Mounting Kits ............................................
SRM-121/SRM-150 LCD Monitor Table 4-18: DVI-D Connector Pinouts.........................................................................................50 Table 5-1: External Peripheral Interface Connectors................................................................56 Table 5-2: Optional RS-232 Touch Panel Connector Pinouts ..................................................59 Table 6-1: OSD Menus.............................................................................................................
SRM-121/SRM-150 LCD Monitor Chapter 1 1 Introduction Page 1
SRM-121/SRM-150 LCD Monitor 1.1 SRM-121/SRM-150 LCD Monitor Overview Figure 1-1: SRM-121/SRM-150 LCD Monitor The SRM series industrial monitor is the latest member of IEI’s line of sophisticated LCD designs, and it has been improved to be RoHS compliant. The SRM series is designed to fit industrial automation, or any other applications that require minimum installation space and flexible configuration.
SRM-121/SRM-150 LCD Monitor IP 65 compliant aluminum front panel Heavy duty aluminum chassis RoHS compliance Wide range operating temperature Wide viewing angle High contrast ratio Advanced thermal and air-flow design 9 ~ 36V DC power input for mobile application Supports panel, rack, wall, stand and arm mounting Optional RS-232 or USB interface touch panel 1.1.
SRM-121/SRM-150 LCD Monitor 1.1.3 Model Variations 1.1.3.1 SRM-121 Model Variations The SRM-121 has ten models variations listed in Table 1-1. Model Number LCD Size Resolution 9~36V Touch Screen Power Input SRM-121 12.1” 800 x 600 No No SRM-121/T-R 12.1” 800 x 600 No RS-232 SRM-121GMS 12.1” 800 x 600 Yes No SRM-121GMS/T-R 12.1” 800 x 600 Yes RS-232 SRM-121-USB/T-R 12.1” 800 x 600 No USB SRM-121GMS-USB/T-R 12.1” 800 x 600 Yes USB SRM-121XA/T-R 12.
SRM-121/SRM-150 LCD Monitor 1.1.3.2 SRM-150 Model Variations The SRM-150 has six models variations listed in Table 1-2. Model Number LCD Size 9~36V Power Input Touch Screen RS-232 USB SRM-150 15” No No No SRM-150/T-R 15” No Yes No SRM-150GMS 15” Yes No No SRM-150GMS/T-R 15” Yes Yes No SRM-150-USB/T-R 15” No No Yes SRM-150GMS-USB/T-R 15” Yes No Yes Table 1-2: SRM-150 Model Variants 1.
SRM-121/SRM-150 LCD Monitor 1.2.1 Front View The front of the SRM series industrial monitor is a flat panel TFT LCD screen surrounded by an aluminum frame. A control button panel (OSD) is located vertically on the right side of the frame with the following control buttons: LCD On/Off Auto Left Right Menu The OSD panel also has one auto-dimming sensor, one power LED and one auto -dimming LED. Figure 1-2 shows the LCD monitor front view of SRM-121 and SRM-150.
SRM-121/SRM-150 LCD Monitor 1.2.2 Rear View The rear panel features fan ventilation holes and four retention screw holes that support a wall-mounting bracket. The retention screw holes are circled in Figure 1-3.
SRM-121/SRM-150 LCD Monitor 1.2.3 Top View The top view provides access to retention screws that secure the back cover to the chassis. The retention screw holes are circled in Figure 1-4 below. Figure 1-4: Top View 1.2.4 Bottom View The bottom view provides access to retention screws that secure the back cover to the chassis. The retention screw holes are circled in Figure 1-5 below.
SRM-121/SRM-150 LCD Monitor 1.2.5 Side View The rear panel shown in Figure 1-6 has the following interfaces. See Section 2.3 for the connector locations.
SRM-121/SRM-150 LCD Monitor 1.2.6 Frame An aluminum frame surrounds the SRM series LCD monitor. This aluminum frame has small screw holes that are used to attach the LCD monitor to a rack mount kit for mounting into a rack or cabinet. The screw holes on SRM-121 and SRM-150 are circled in Figure 1-7 and Figure 1-8.
SRM-121/SRM-150 LCD Monitor 1.3 Series Specifications Table 1-3 shows the SRM Series specifications. Model SRM-121 SRM-121XA/XMA SRM-150 LCD Size 12.1” 12.1” 15” Input Interface Analog VGA and DVI-D Resolution 800 x 600 Brightness 1000 cd/m2 800 cd/m2 Contrast 700:1 600:1 Display Color 262K (6 bit/color) or 16.7M (8 bit/color) Pixel Pitch 0.
SRM-121/SRM-150 LCD Monitor 1.4 Certifications All SRM series industrial monitor models comply with the following international standards: RoHS IP 65 For a more detailed description of these standards, please refer to Sections B.1 and B.2.
SRM-121/SRM-150 LCD Monitor Chapter 2 2 Mechanical Overview Page 13
SRM-121/SRM-150 LCD Monitor 2.1 Introduction This chapter describes the general mechanical overview of the SRM series monitors including front and rear panel, available interfaces and overall dimensions. 2.2 Front Panel The front panel of the SRM series industrial monitor is comprised of a TFT LCD in an aluminum frame with an OSD control panel. Figure 2-1 shows the front panel of the SRM series.
SRM-121/SRM-150 LCD Monitor 2.3 Rear Panel All peripheral device connectors are located on the rear panel of the SRM series industrial monitor. The following rear panel connectors may be found on the SRM series. Figure 2-2 shows the location of the connectors. 12V power connector 9V ~ 36V terminal block DVI-D connector RS-232 serial connector VGA connector Figure 2-2: SRM Series Rear Panel Connector Locations 2.
SRM-121/SRM-150 LCD Monitor 2.4.1 SRM-121 Physical Dimensions The physical dimensions of the SRM-121 are shown in Figure 2-3.
SRM-121/SRM-150 LCD Monitor 2.4.2 SRM-150 Physical Dimensions The physical dimensions of the SRM-150 are shown in Figure 2-4.
SRM-121/SRM-150 LCD Monitor 2.5 Mounting Kits The following sections describe the various optional mounting kits available for each model of the SRM series industrial monitor. Refer to Section 0 for detailed instructions on the different mounting methods for the monitors. Table 2-1 lists the mounting kits available for the SRM series monitor.
SRM-121/SRM-150 LCD Monitor Model Mounting Clamps SRM-121 10 SRM-150 10 Table 2-2: Panel Mounting Clamps 2.6.2 Rack and Cabinet Mounting Each model of the SRM series industrial monitor has a series of holes located on the rear of the front panel for securing the monitor to the rack mounting kit. Table 2-3 lists the number of holes each monitor has to secure the monitor to the rack mounting kit. Model Holes SRM-121 10 SRM-150 12 Table 2-3: Rack Mounting Holes 2.6.
SRM-121/SRM-150 LCD Monitor Chapter 3 3 LCD and Touch Panel Specifications Page 20
SRM-121/SRM-150 LCD Monitor 3.1 LCD Specifications 3.1.1 LCD Overview The SRM series industrial monitors use the following LCD panels. SRM-121: MITSUBISHI AA121SN02 SVGA TFT LCD SRM-150: MITSUBISHI AA150XN08 XGA TFT LCD Detailed specifications for the LCD screens are listed in the following sections. 3.1.2 SRM-121 LCD Specifications Table 3-1 lists the LCD specifications of the SRM-121. Model SRM-121 Size 12.1” MFR/Model MITSUBISHI AA121SN02 Resolution SVGA (800 x 600) Display Area (mm) 246.
SRM-121/SRM-150 LCD Monitor Model Power Supply Current for LCD SRM-121 300mA / 450mA Voltage: 540 Vrms Lamp Voltage/Current Current: 12.0 mArms/14.0 mAms (Max.) 1000 Vrms (25°C)/ 1200 Vrms (0°C)/ Starting Lamp Minimum Voltage 1290 Vrms (-20°C) Operating Temperature -20°C ~70°C Operating Humidity 5%~90% RH. Storage Temperature -20°C ~80°C Shock Level (Non-operation) 1470 m/s2 (100G), Waveform 2ms. 9.8 m/s2 (1.0G) zero to peak, frequency Vibration Level (Non-operation) range 5-500Hz sweep rate 0.
SRM-121/SRM-150 LCD Monitor Model SRM-121XA/XMA View Angle (H/V) 120 / 120 Brightness (cd/m2) 1000 Contrast Ratio 700:1 Response Time (ms) TR: 6 TF: 19 Interface LVDS (6 bit/8 bit) Input Voltage (V) 3.3V Backlight 4 CCFL Power Supply Voltage for LCD 3.3V / 3.6V (Max.) Power Supply Current for LCD 300mA / 450mA Voltage: 540 Vrms Lamp Voltage/Current Current: 13.
SRM-121/SRM-150 LCD Monitor 3.1.4 SRM-150 LCD Specifications Table 3-3 lists the LCD specifications of the SRM-150. Model SRM-150 Size 15” MFR/Model MITSUBISHI AA150XN08 Resolution XGA (1024 x 768) Active Area (mm) 246.0 x 184.5 Pixel Pitch (mm) 0.297 x 0.297 Number of Colors 262K(6 bit/color), 16.7M(8 bit/color) View Angle (H/V) 150 / 110 Brightness (cd/m2) 800 Contrast Ratio 600:1 Response Time (ms) TR: 6 TF: 19 Interface LVDS (6 bit/8 bit) Input Voltage (V) 3.
SRM-121/SRM-150 LCD Monitor Model SRM-150 Operating Humidity 5%~90% RH. Storage Temperature -20°C ~80°C Shock Level (Non-operation) 980 m/s2 (100G), Waveform 2ms. 9.8 m/s2 (1.0G) zero to peak, frequency Vibration Level (Non-operation) range 5-500Hz sweep rate 0.
SRM-121/SRM-150 LCD Monitor 3.2 Optional Touch Panels IEI offers optional touch panels for the SRM series industrial monitors with the following features: Small border customized design All size touch panel design Customized activation force and palm rejection Customized optical characteristics High reliability and durability in the field 3.2.1 Touch Panel Models Table 3-4 lists the SRM series industrial monitors and their associated touch panels.
SRM-121/SRM-150 LCD Monitor 3.2.2 Touch Panel Dimensions Table 3-5 shows the touch panel dimensions in millimeters. Model Dimension Width Length Thick Dimensional Outline: 204 268 2.1 Viewing Area: 188 250 - Active Area: 185 246 - Dimensional Outline: 257.5 333.6 2.9 Viewing Area: 232.1 308.2 - Active Area: 228.1 304.
SRM-121/SRM-150 LCD Monitor 3.2.3 Touch Panel Specifications Table 3-6 lists the touch panel specifications.
SRM-121/SRM-150 LCD Monitor 3.2.4 Touch Panel RS-232 Controller Specifications Table 3-7 lists the touch panel RS-232 controller specifications. Circuit Board Dimension 20mm x 75mm (0.79inches x 2.95inches)----(5-Wire) Power Requirements D.C.
SRM-121/SRM-150 LCD Monitor 3.2.5 Touch Panel USB Controller Specifications Table 3-8 lists the touch panel USB controller specifications. Circuit Board Dimension 20mm x 75mm (0.79inches x 2.95inches)----(5-Wire) Power Requirements D.C.+5V (100mA typical, 50mV peak to peak maximum ripple and noise) Operating Temperature 0°C to 50°C Storage Temperature -40°C to 80°C Relative Humidity 95% at 60°C Interface USB 1.
SRM-121/SRM-150 LCD Monitor Chapter 4 4 AD Board Page 31
SRM-121/SRM-150 LCD Monitor 4.1 AV-5300 AD Board Overview The SRM series industrial monitor AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. The following sections describe the AV-5300 AD board in detail.
SRM-121/SRM-150 LCD Monitor 4.1.
SRM-121/SRM-150 LCD Monitor 4.1.2 AV-5300 AD Board Layout Figure 4-2 shows the on-board peripheral connectors and on-board jumpers.
SRM-121/SRM-150 LCD Monitor 4.1.3 AV-5300 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the AV-5300 AD board. Detailed descriptions of these connectors can be found in Section 4.2.
SRM-121/SRM-150 LCD Monitor 4.1.5 AV-5300 On-board Jumpers Table 4-3 lists the on-board jumpers. A detailed description of these jumpers can be found in Section 4.3. Jumper Type Label LCD Panel Power Input Select 6-pin header JP4 LCD Panel Voltage Select 6-pin header JP1 Table 4-3: AV-5300 On-board Jumpers 4.2 AV-5300 Internal Peripheral Connectors Internal peripheral connectors on the AV-5300 AD board are only accessible when the board is outside of the monitor.
SRM-121/SRM-150 LCD Monitor 4.2.1 Auto-Dimming Connector CN Label: CN16 CN Type: 6-pin wafer connector CN Pinouts: See Table 4-4 CN Location: See Figure 4-3 The auto-dimming connector connects to an external auto-dimming sensor. PIN DESCRIPTION 1 +3.
SRM-121/SRM-150 LCD Monitor 4.2.2 Debug Port Connector CN Label: CN4 CN Type: 4-pin wafer connector CN Pinouts: See Table 4-5 CN Location: See Figure 4-4 Use the debug port connector to update the AD board BIOS.
SRM-121/SRM-150 LCD Monitor 4.2.3 External OSD and LED Indication Connector CN Label: CN3 CN Type: 9-pin wafer connector CN Pinouts: See Table 4-6 CN Location: See Figure 4-5 The External OSD and LED Indication connector connects to an external OSD controller.
SRM-121/SRM-150 LCD Monitor 4.2.4 Backlight Inverter Connector CN Label: CN2 CN Type: 6-pin wafer connector CN Pinouts: See Table 4-7 CN Location: See Figure 4-6 The Inverter connector connects to the LCD backlight. Using the BKLT_EN signal to control the inverter status (ON/OFF) and the BKLT_ADJ signal to adjust brightness of inverter by OSD brightness function.
SRM-121/SRM-150 LCD Monitor 4.2.5 LVDS Output Connector CN Label: CN8 CN Type: 30-pin connector CN Pinouts: See Table 4-8 CN Location: See Figure 4-7 Use either LVDS output connector to connect the LCD panel to a system.
SRM-121/SRM-150 LCD Monitor Figure 4-7: LVDS Output Connector Location NOTE: The supply voltage (3.3V (Default), 5V or 12V) can be selected via JP1.
SRM-121/SRM-150 LCD Monitor 4.2.6 Power Output Connector CN Label: CN12, CN13 CN Type: 2-pin wafer connector CN Pinouts: See Table 4-9 and Table 4-10 CN Location: See Figure 4-8 The AV-5300 supports two power output connectors, one for 12V and the other for 5V. PIN DESCRIPTION 1 +12V 2 GND Table 4-9: Power Output Connector Pinouts (CN12) PIN DESCRIPTION 1 +5V 2 GND Table 4-10: Power Output Connector Pinouts (CN13) Figure 4-8: Power Output Connector Locations 4.2.
SRM-121/SRM-150 LCD Monitor PIN DESCRIPTION 1 +12V 2 GND Table 4-11: Power Input Connector Pinouts (CN24) PIN DESCRIPTION 1 +12V Input 2 GND 3 +9V~36V to external power module Table 4-12: Power Input Connector Pinouts (CN25) Figure 4-9: Power Input Connector Locations Page 44
SRM-121/SRM-150 LCD Monitor 4.2.8 VGA Connector CN Label: J1 CN Type: 10-pin box header CN Pinouts: See Table 4-13 CN Location: See Figure 4-10 In addition to the standard DB-15 female VGA connector (J1), a VGA connection can also be made through the on-board CN2 10-pin header.
SRM-121/SRM-150 LCD Monitor 4.3 AV-5300 On-board Jumpers NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper. The AV-5300 has two on-board jumpers (Table 4-3).
SRM-121/SRM-150 LCD Monitor 4.3.1 LCD Panel Power Input Jumper Jumper Label: JP4 Jumper Type: 6-pin header Jumper Location: See Figure 4-12 Jumper Settings: See Table 4-14 The JP4 jumper sets the input source from either the 12V power connector (J3) or the external terminal block. JP4 Description 1-3, 2-4 +12V from power connector (J3) (Default) 3-5, 4-6 Input with external connector (Need external power module) Table 4-14: LCD Panel Power Input Jumper Settings 4.3.
SRM-121/SRM-150 LCD Monitor 4.4 AV-5300 External (Rear Panel) Connectors Figure 4-13 shows the AV-5300 external (rear panel) connectors. The peripheral connectors on the back panel of the monitor can connect to external devices. The peripheral connectors on the rear panel are: 1 x DC 12V connector 1 x DVI-D connector 1 x VGA connector Figure 4-13: AV-5300 External (Rear Panel) Connectors 4.4.
SRM-121/SRM-150 LCD Monitor 4.4.2 VGA Connector CN Label: J5 CN Type: D-sub 15 female connector CN Pinouts: See Table 4-17 and Figure 4-14 CN Location: See Figure 4-13 Use the standard D-sub 15-pin VGA connector to connect the monitor to a system.
SRM-121/SRM-150 LCD Monitor 4.4.3 DVI-D Connector CN Label: J2 CN Type: D-sub DVI female connector CN Pinouts: See Table 4-18 and Figure 4-15 CN Location: See Figure 4-13 The 24-pin female dual link digital only DVI [Digital Visual Interface] connector is a standard for high-speed, high-resolution digital displays. Use the DVI-D connector to connect the LCD to a system.
SRM-121/SRM-150 LCD Monitor Chapter 5 5 Installation Page 51
SRM-121/SRM-150 LCD Monitor 5.1 Installation Precautions When installing the SRM series industrial monitor, please follow the precautions listed below: Read the user manual: The user manual provides a complete description of the SRM series industrial monitor, installation instructions and configuration options. DANGER! Disconnect Power: Power to the monitor must be disconnected when installing the SRM series industrial monitor, or before any attempt is made to access the rear panel.
SRM-121/SRM-150 LCD Monitor 5.2 Unpacking 5.2.1 Packaging When shipped, the SRM series industrial monitor is wrapped in a plastic bag. Two polystyrene ends are placed on either side of the monitor. The monitor is then placed into a first (internal) cardboard box. This box is then sealed and placed into a second (external) cardboard box. The second box is also sealed. A bag containing accessory items is placed underneath the monitor, at the bottom of the internal (first) box. 5.2.
SRM-121/SRM-150 LCD Monitor 5.2.3 Packing List All the monitors in the SRM series are shipped with the following components: Quantity Item Image 45W AC power adapter 1 1 AC power cord 1 DVI cable 1 Screw kit 1 VGA cable 1 User manual and driver CD 1 Touch screen driver CD (T-R models only) 1 Touch pen (T-R models only) If any of these items are missing or damaged, contact the distributor or sales representative immediately.
SRM-121/SRM-150 LCD Monitor 5.3 Pre-installation Preparation 5.3.1 Tools Before installing the SRM series industrial monitor, make sure the following tools are on hand: Phillips (crosshead) screwdriver: All the retention screws on the system are Phillips screws. Soft working mat: When the SRM series industrial monitor is installed, the screen is placed on the working surface.
SRM-121/SRM-150 LCD Monitor Step 4: Use the jumper(s) to set the correct voltage input. (See Section 4.3.2) Replace the rear panel. Step 5: Replace all removed screws.Step 0: 5.4 Connectors Table 5-1 lists the external peripheral interface panel connectors for the SRM series industrial monitors.
SRM-121/SRM-150 LCD Monitor 5.4.1 Rear Panel Connectors Overview Figure 5-1: Monitor Rear Panel Connections Figure 5-1 shows all the possible rear panel connectors for the SRM series LCD monitor. The following sections fully describe the rear panel connectors for the SRM series LCD monitor. 5.4.2 VGA Connector Use the rear panel standard 15-pin female VGA connector to connect the monitor to the system graphics interface. See Section 4.4.2 for the VGA connector location and pinouts.
SRM-121/SRM-150 LCD Monitor 5.4.3 DVI-D Connector Use the rear panel standard 24-pin female DVI-D connector to connect the monitor to the system graphics interface. See Section 0 for the DVI-D connector location and pinouts. 5.4.4 12V Power Connector Use the rear panel +12V DC jack to connect the monitor to a power source. Figure 5-2: 12V Power Connector 5.4.5 DC Power Connector Use the rear panel 3-pin terminal block DC power connector to connect the monitor to a DC power source.
SRM-121/SRM-150 LCD Monitor 5.4.6 Optional RS-232 Touch Panel Connector Use the rear panel standard RS-232 DB-9 female touch panel connector to connect the monitor to the system graphics interface.
SRM-121/SRM-150 LCD Monitor 5.5 Mounting the SRM Series LCD Monitor The SRM series LCD monitor can be mounted in a panel, cabinet, rack, or wall. The monitor can also be mounted on a monitor arm or stand. The mounting methods are described below. CAUTION: When mounting the monitor take care to tighten the retention screws or bolts until fully secure, but do not over tighten. Over tightening the retention screws or bolts may cause them to become stripped, rendering them useless. 5.5.
SRM-121/SRM-150 LCD Monitor Figure 5-5: Panel Opening Step 3: Slide the monitor through the hole until the metal frame is flushed against the panel (Figure 5-6).
SRM-121/SRM-150 LCD Monitor Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of the monitor, behind the metal frame. Figure 5-7 shows the location of clamp insertion holes on one side of the LCD monitor. Refer to Table 2-2 for the mounting clamps required for each model.
SRM-121/SRM-150 LCD Monitor Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 5-8).
SRM-121/SRM-150 LCD Monitor 5.5.2 Cabinet and Rack Installation The SRM series provides optional rack mount kits for industrial racks. To mount the SRM series LCD monitor into a cabinet/rack, please follow the steps below. Step 1: The back of the metal frame surrounding the SRM series LCD monitor has several retention screw holes for a rack mount kit. See Figure 1-7 and Figure 1-8.
SRM-121/SRM-150 LCD Monitor Step 5: Slide the monitor with the attached rack mount kit into a rack or cabinet (Figure 5-10). Figure 5-10: Install into a Cabinet/Rack Step 6: Once the monitor with the attached cabinet/rack has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 5-10).
SRM-121/SRM-150 LCD Monitor 5.5.3 Wall Mounting To mount the SRM series industrial monitor onto a wall, please follow the steps below. Step 1: Select a location on the wall for the wall-mounting bracket. Step 2: Carefully mark the locations of the four bracket screw holes on the wall. Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention screws. Step 4: Align the wall-mounting bracket screw holes with the pilot holes.
SRM-121/SRM-150 LCD Monitor Figure 5-12: Monitor Support Screws Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket.
SRM-121/SRM-150 LCD Monitor Step 8: Carefully insert the screws through the holes and gently pull the monitor downwards until the monitor rests securely in the slotted holes (Figure 5-13). Ensure that all four of the mounting screws fit snuggly into their respective slotted holes.
SRM-121/SRM-150 LCD Monitor 5.5.4 Monitor Stand Installation The SRM series industrial monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-14). Figure 5-14: VESA Mounting Holes The monitor stand mounting plate has a matching VESA hole pattern. To mount the SRM series industrial monitor onto a stand, please follow the steps below.
SRM-121/SRM-150 LCD Monitor Step 2: Secure the monitor to the stand with the supplied retention screws (Figure 5-15).
SRM-121/SRM-150 LCD Monitor 5.5.5 Monitor Arm Installation The SRM series industrial monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-14). The monitor arm mounting plate has a matching VESA hole pattern. To mount the SRM series industrial monitor onto a monitor arm, please follow the steps below.
SRM-121/SRM-150 LCD Monitor Chapter 6 6 On-Screen-Display (OSD) Controls Page 72
SRM-121/SRM-150 LCD Monitor 6.1 User Mode OSD Structure 6.1.1 OSD Buttons There are several on-screen-display (OSD) control buttons oriented either vertically along the right hand side of the monitor front panel. Figure 6-1 shows a typical arrangement of OSD controls. Figure 6-1: OSD Control Buttons for All Models LCD ON/OFF Button Press this button to turn the LCD monitor on or off. When the LCD monitor is on, the power LED is turned on in green.
SRM-121/SRM-150 LCD Monitor Menu/Enter Button Press this button to open the OSD window. When inside a menu, press this button to confirm the function adjustment or selection of the item. There may be several levels in one item. As you select an item in the menu, the sub-items will be displayed. The OSD control panel also includes one sensor and two LED. Ambient Light Sensor The ambient light sensor detects the brightness of ambient environment when the auto-dimming function is turned on.
SRM-121/SRM-150 LCD Monitor 6.1.2 OSD Menu Structure Table 6-1 shows the OSD menu structure for all models of the SRM series LCD monitor. Level 0 Level 1 Value Main Display Features Menu Brightness 0 to 100 Contrast 0 to 100 Sharpness 1 to 5 Volume This menu is currently disabled, Mute and will be implemented with Speaker Menu models equipped with speakers.
SRM-121/SRM-150 LCD Monitor 6.2 Using the OSD OSD menu options are described below. 6.2.1 Main Display Features Main display features are shown in Figure 6-2. Figure 6-2: Main Display Features The brightness option adjusts the brightness of screen. This function adjusts the offset value of ADC. Setting this value too Brightness high or too low will affect the quality of image. When the autodimming function is turned on, the brightness control is not effective.
SRM-121/SRM-150 LCD Monitor 6.2.2 Color Color options are shown in Figure 6-3. Figure 6-3: Color Options The Color menu fine-tunes the palette of color hues for the LCD. 9300k NTSC standard Kelvin 7500k NTSC standard Kelvin 6500k NTSC standard Kelvin User Temp This item allows fine-tuning the balance among Red, Green, and Blue color hues if images look garish or unrealistic.
SRM-121/SRM-150 LCD Monitor 6.2.3 Image Settings The image settings are shown in Figure 6-4. Figure 6-4: Image Settings Menu Image settings are described below. Page 78 Auto Color Automatically adjusts the color settings. Width Adjusts the width of the display screen. Phase Adjusts the input signal and dot clock position (Analog only) H. Position Adjusts the horizontal position of the display screen. V.
SRM-121/SRM-150 LCD Monitor 6.2.4 OSD Configurations The OSD configurations are shown in Figure 6-5. Figure 6-5: OSD Configurations Menu OSD Configurations are described below. OSD Time Out Determines how many seconds the OSD screen stays on screen before it disappears when OSD is left unattended. Adjusts the OSD position on the screen. Position 1 is in the OSD Position upper left of the screen, position 2 in the upper right and position 3 in the center.
SRM-121/SRM-150 LCD Monitor 6.2.
SRM-121/SRM-150 LCD Monitor 6.2.6 Auto-Dimming Configurations The SRM industrial monitor features an auto-dimming LCD that can automatically adjust the backlight brightness according to the ambient light. If the auto-dimming function is turned on, the backlight turns brighter when the ambient illuminance is high. The backlight dims automatically when the ambient brightness level is low. The SI unit of illuminance is “lux”. Lux measures the intensity of light.
SRM-121/SRM-150 LCD Monitor The Figure 6-7 shows the SRM-121 default linearity of the LCD backlight and ambient light. When the sensor detects the ambient illuminance as 5200 LUX or above, the SRM 40000 35000 25000 30000 20000 15000 5000 10000 4500 4000 3500 2500 3000 2000 1500 100%100%100% 100%100% 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 1000 0% 500 1000 900 800 700 600 500 400 300 200 100 0 0 LCD Brightness (cd/m2) series industrial monitor adjusts the LCD brightness to 100%.
SRM-121/SRM-150 LCD Monitor Auto-Dimming Configurations are described below. Turn on or turn off auto-dimming function. When auto-dimming Light Enable is turned on, the auto-dimming LED on the OSD panel is on ON/OFF and the monitor automatically adjusts the brightness according to ambient light conditions. Adjusts the maximum LCD brightness value. The value is from Light Max 0% to 100%. The value cannot be smaller than the minimum LCD brightness value. Adjusts the minimum LCD brightness value.
SRM-121/SRM-150 LCD Monitor To keep the LCD brightness within a specific range, not the 0~100% wide range, adjust the minimum and maximum value of the LCD backlight. For example, set the Light Min. to 30 and the Light Max. to 70. Then, the adjustable LCD brightness range is among 30% to 70%. By doing this, the LCD brightness does not become too bright or too dark if the ambient light reaches the default maximum or minimum value. LUX Max. and LUX Min. The SRM series is an ideal product for outdoor display.
SRM-121/SRM-150 LCD Monitor Keep Light Max. in default setting: 100 Keep Light Min. in default setting: 0 Keep LUX Min.
SRM-121/SRM-150 LCD Monitor Chapter 7 7 Software Drivers Page 86
SRM-121/SRM-150 LCD Monitor 7.1 Introduction The touch panel controller enables analog resistive touch panels for four-wire, five-wire & eight-wire models. The controller directly communicates with the PC system through the touch panel communications interface. The controller design is superior in sensitivity, accuracy, and friendly operation. The touch panel driver emulates the left mouse button and the right mouse button functions.
SRM-121/SRM-150 LCD Monitor Figure 7-1: Driver CD Pop Up Screen Step 3: Select the operating system installed on the system from the menu on the left side of the screen. NOTE: The following description is for driver installation using a Windows 2000 OS. If a different OS is installed, please refer to the driver user manual for the relevant OS. The driver user manuals can be accessed by selecting “User Manual” from the menu on the left side of the “Driver CD Pop Up Screen”.
SRM-121/SRM-150 LCD Monitor Figure 7-2: Install Shield Wizard Preparation Step 5: After the Install Shield Wizard is ready, a welcome screen appears (Figure 7-3). Figure 7-3: Welcome Screen Step 6: To continue the installation process click NEXT.
SRM-121/SRM-150 LCD Monitor Step 7: An Install PS/2 interface driver screen appears (Figure 7-4). It is not necessary to install the PS/2 interface driver. To continue click NEXT. Figure 7-4: Install PS/2 Interface Driver Step 8: Four point calibration options are then selected. Four point calibrations can be done every time a user boots up, during the next time the system boots or never. Select if and when a four-point calibration should be done. Click NEXT to continue.
SRM-121/SRM-150 LCD Monitor Figure 7-5: Install PS/2 Interface Driver Step 9: The user is then prompted to ensure the touch monitor or the RS-232 touch controller is plugged into the system (Figure 7-6). Once the touch controller is plugged into the system, click OK.
SRM-121/SRM-150 LCD Monitor Step 10: The user is then prompted to select a file directory in which the touch kit controller is installed (Figure 7-7). The default directory is “C:\Program Files\TouchKit.” If a different folder must be used, select browse and then select the folder. Once the folder is selected, click NEXT to continue.
SRM-121/SRM-150 LCD Monitor Step 11: The user is then prompted to select a file directory in which the program icons are saved (Figure 7-8). The default folder is “TouchKit.” If a different folder must be used, select a folder from the list shown. Once the folder is selected, click NEXT to continue.
SRM-121/SRM-150 LCD Monitor Step 12: The program then starts installing (Figure 7-9).
SRM-121/SRM-150 LCD Monitor Step 13: Once the program is finished installing, the user is prompted to restart the computer now or to restart the computer later (Figure 7-10). Select when the computer should be restarted and click “FINISH” to complete the driver installation procedure.Step 0: Figure 7-10: Installation Complete 7.3 Touch Panel Driver Configuration To configure the touch panel driver options, refer to the TouchKit user manual located on the driver installation CD.
SRM-121/SRM-150 LCD Monitor Chapter 8 8 Gasket Replacement Page 96
SRM-121/SRM-150 LCD Monitor 8.1 Gasket Replacement A gasket used for a long time may gradually lose its ability to protect the monitor from fluids and vapors; scratches or dirt may also accumulate. It is recommended that the gasket be replaced yearly. NOTE: If the monitor is mounted vertically, first remove it and place it on a flat, level surface with the display screen facing down before changing the gasket. Step 1: Remove the old gasket from the sides of the monitor.
SRM-121/SRM-150 LCD Monitor Appendix A A Safety Precautions Page 98
SRM-121/SRM-150 LCD Monitor WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the SRM Series. A.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: A.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. Follow the electrostatic precautions outlined below whenever the SRM Series is opened.
SRM-121/SRM-150 LCD Monitor A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the SRM Series may result in permanent damage to the SRM Series and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the SRM Series. Dry climates are especially susceptible to ESD.
SRM-121/SRM-150 LCD Monitor The interior of the SRM Series does not require cleaning. Keep fluids away from the SRM Series interior. Be cautious of all small removable components when vacuuming the SRM Series. Turn the SRM Series off before cleaning the SRM Series. Never drop any objects or liquids through the openings of the SRM Series. Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the SRM Series.
SRM-121/SRM-150 LCD Monitor Appendix B B Certifications Page 102
SRM-121/SRM-150 LCD Monitor B.1 RoHS Compliant All models in the SRM LCD monitor series comply with the Restriction of Hazardous Materials (RoHS) Directive. This means that all components used to build the industrial workstations and the workstation itself are RoHS compliant.
SRM-121/SRM-150 LCD Monitor C Index Page 104
SRM-121/SRM-150 LCD Monitor 1 12V J 33, 35, 42, 47, 48 jumper 46, 47 jumpers 34, 36, 46 A AD board 32, 33, 35, 36 AD Board 32, 33, 34 anti-static precautions LCD 100 anti-static wristband 100 handling 100 self-grounding 100 auto-dimming 83 32, 33, 34, 35, 36, 46, 48 21 SRM-121GS LCD Specifications 21, 22 SRM-150GS LCD Specifications 24 Light Max 83 Light Min 83 LUX Max 83 LUX Min 83 C M Certifications Model Variations IP 65 103 RoHS 103 connectors 33, 34, 35, 36,
SRM-121/SRM-150 LCD Monitor P LCD Size 11 Mounting 11 Packing List 54 Operation Temperature 11 peripheral interface connectors 35 OSD Function 11 Physical Dimensions 15 Pixel Pitch 11 Pinouts 37, 38, 39, 40, 41, 43, 44, 45, 48, 49, Resolution 11 Weight 11 50 Specifications R Standard Features Relative Humidity 29, 30 Resolution 29, 30 RoHS 2, 3 RS-232 2, 29 RS-232 Touch Panel Connector 29, 30 59 2 T terminal block 47 touch panel 30 Touch Panel 29, 30 Touch Panel D
