RPC-6106/6108 Rackmount LCD Workstation RPC-6106/RPC-6108 LCD Workstation User Manual Page i
RPC-6106/6108 Rackmount LCD Workstation Revision MODEL RPC-6106/6108 4U 7-slot LCD Workstation Revision Number Description Date of Issue 1.
RPC-6106/6108 Rackmount LCD Workstation Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
RPC-6106/6108 Rackmount LCD Workstation Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the RPC-6106/6108 LCD Workstation from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the RPC-6106/6108 Rackmount LCD Workstation package.
RPC-6106/6108 Rackmount LCD Workstation Table of Contents 1 INTRODUCTION..................................................................................................... 1 1.1 RPC-6106/6108 OVERVIEW ...................................................................................... 2 1.2 RPC-6106/6108 FEATURES ....................................................................................... 2 1.3 MODEL VARIATIONS ................................................................................
RPC-6106/6108 Rackmount LCD Workstation 4.3 PRE-INSTALLATION PREPARATION ............................................................................ 20 4.3.1 System Planning............................................................................................... 20 4.3.2 Tools ................................................................................................................. 21 4.4 INSTALLATION PROCEDURES ..................................................................................
RPC-6106/6108 Rackmount LCD Workstation 6.1.1 OSD Buttons..................................................................................................... 48 6.1.2 OSD Menu Structure ........................................................................................ 49 6.2 USING THE OSD....................................................................................................... 50 6.2.1 Main Display Features..................................................................................
RPC-6106/6108 Rackmount LCD Workstation List of Figures Figure 2-1: RPC-6106/6108 Front Panel (External) ....................................................6 Figure 2-2: RPC-6106/6108 14-Slot Rear Panel ..........................................................7 Figure 2-3: RPC-6106/6108 Side Panel........................................................................7 Figure 2-4: RPC-6106/6108 Internal Overview ............................................................
RPC-6106/6108 Rackmount LCD Workstation Figure 6-3: Color Options...........................................................................................51 Figure 6-4: Language Menu .......................................................................................52 Figure 6-5: OSD Configurations Menu ......................................................................53 Figure 6-6: Signal Menu..............................................................................................
RPC-6106/6108 Rackmount LCD Workstation List of Tables Table 1-1: RPC-6106/6108 Model Options ..................................................................3 Table 2-1: General Physical Dimensions ....................................................................8 Table 3-1: RPC-6106/6108 Specifications .................................................................12 Table 3-2: LCD Specifications....................................................................................
RPC-6106/6108 Rackmount LCD Workstation Chapter 1 1 Introduction Page 1
RPC-6106/6108 Rackmount LCD Workstation 1.1 RPC-6106/6108 Overview The RPC-6106/6108 is a PC/AT compatible workstation designed for industrial applications. It has a rugged steel chassis specially designed to work under harsh environmental conditions while also being highly reliable. The RPC-6106/6108 features 7-slot passive backplanes and a full line of dependable AC/DC power supplies. The RPC-6106/6108 can withstand shock, vibration, dust and a wide range of temperatures in industrial environments.
RPC-6106/6108 Rackmount LCD Workstation Model LCD RPC-6108B/ACE-4525AP/T-R 8.4” Touch Screen Yes SBC Form Factor Half-size CPU card Expansion Slots 7 Table 1-1: RPC-6106/6108 Model Options 1.4 Certification All RPC-6106/6108 Rackmount LCD Workstations comply with the following international standards: RoHS For a more detailed description of this standard, please refer to Appendix A.
RPC-6106/6108 Rackmount LCD Workstation THIS PAGE IS INTENTIONALLY LEFT BLANK Page 4
RPC-6106/6108 Rackmount LCD Workstation Chapter 2 2 Mechanical Overview Page 5
RPC-6106/6108 Rackmount LCD Workstation 2.1 External Overview The following sections describe the physical layout of the RPC-6106/6108 Rack-mount LCD Workstation. 2.1.1 Front Panel The RPC-6106/6108 Rack-mount LCD Workstation has the following front panel items: Heavy duty steel front panel 6.5”/8.
RPC-6106/6108 Rackmount LCD Workstation 2.1.2 Rear Panel The RPC-6106/6108 Rackmount LCD Workstation has the following rear panel items: Internal PSU 2 x 8cm cooling fans Figure 2-2: RPC-6106/6108 14-Slot Rear Panel 2.1.3 Side Panel The two side panels of the RPC-6106/6108 Rackmount LCD Workstation each has four screw holes for a handle bracket.
RPC-6106/6108 Rackmount LCD Workstation 2.1.4 Internal overview Figure 2-4 shows the internal components of the RPC-6106/6108 LCD workstation. Figure 2-4: RPC-6106/6108 Internal Overview 2.2 Physical Dimensions The following sections describe the physical dimensions of the RPC-6106 and RPC-6108. 2.2.1 General Physical Dimensions General physical dimensions for the RPC-6106/6108 are shown in Table 2-1.
RPC-6106/6108 Rackmount LCD Workstation 2.2.2 RPC-6106 Physical Dimensions The physical dimensions of the RPC-6106 are shown in Figure 2-5.
RPC-6106/6108 Rackmount LCD Workstation 2.2.3 RPC-6108 Physical Dimensions The physical dimensions of the RPC-6108 are shown in Figure 2-5.
RPC-6106/6108 Rackmount LCD Workstation Chapter 3 3 Detailed Specifications Page 11
RPC-6106/6108 Rackmount LCD Workstation 3.1 RPC-6106/6108 Specifications Table 3-1 shows the RPC-6106/6108 specifications. RPC-6106 RPC-6108 LCD Type 6.5" TFT 8.4" TFT Chassis Heavy-duty metal Max. Slot 7 slots Drive Bay 2 x 3.5” HDD I/O Port 2 x USB ports Indicators Power, HDD Switches/Buttons 1 x Power switch 1 x Reset button Cooling fan 2 x 8cm (rear panel) OSD function Yes Mounting Rack Mount Rack Height 4U Touch Panel (optional) Resistive type with RS-232 interface.
RPC-6106/6108 Rackmount LCD Workstation 3.2 LCD Specifications Table 3-2 lists the RPC-6106/6108 LCD specifications. RPC-6106 RPC-6108 Size 6.5” 8.4” Input Interface Analog VGA Analog VGA Resolution VGA (640 x 480) SVGA (800 x 600) Pixel Pitch (mm) 0.207 0.213 Typical White Luminance (cd/m2) 400 220 Contrast Ratio 550:1 500:1 Number of Colors 262K 262K Table 3-2: LCD Specifications 3.3 ACE-4525AP PSU Specifications Table 3-3 lists the ACE-4525AP power supply specifications.
RPC-6106/6108 Rackmount LCD Workstation +5Vsb 0.1A 2.5A 50mV +12V1, +12V2 total Current ≦18W Total Current of +3.3V & +5V & +12V ≦232W Total Current of +3.3V & +5V ≦100W GENERAL Power 250W PFC Active Hold-up Time 18ms minimum Efficiency 70% MTBF 100,000hrs Temperature 0°C ~ 50°C (Operating) -20 °C ~ 80°C (Storage) Dimensions 190 x 100 x 40.5 mm Output Connectors 1 x 20+4pin ATX 1 x 4-pin 12V CPU 4 x HDD/CDROM 1 x FDD 2 x SATA Table 3-3: ACE-4525AP PSU Specifications 3.
RPC-6106/6108 Rackmount LCD Workstation Chapter 4 4 Installation Page 15
RPC-6106/6108 Rackmount LCD Workstation 4.1 Installation Considerations 4.1.1 Installation Precautions When installing the RPC-6106/6108, please follow the precautions listed below: Read the user manual: The user manual provides a complete description of the RPC-6106/6108 Rackmount LCD Workstation, installation instructions and configuration options. Turn Off Power: When installing the RPC-6106/6108 Rackmount LCD Workstation, make sure the power is off.
RPC-6106/6108 Rackmount LCD Workstation o o Memory modules (DIMMs) CompactFlash® disks Backplane/Motherboard: The backplane or motherboard installed in the RPC-6106/6108 Rackmount LCD Workstation is separately purchased. Disk Drives: Disk drives installed into the RPC-6106/6108 Rackmount LCD Workstation are separately purchased. Disk drive support is CPU card dependent. Before purchasing a CPU card or disk drives, please check the CPU card disk drive support. 4.2 Unpacking 4.2.
RPC-6106/6108 Rackmount LCD Workstation Step 1: Use box cutters, a knife or a sharp pair of scissors to open the top of the external (second) box. Step 2: Open the external (second) box. Step 3: Use box cutters, a knife or a sharp pair of scissors to open the top of the internal (first) box. Step 4: Lift the workstation out of the boxes. Step 5: Remove both polystyrene ends from each side. Step 6: Pull the plastic cover off the workstation.
RPC-6106/6108 Rackmount LCD Workstation Quantity Description 1 RPC-6106/6108 LCD workstation 2 Handles 1 Power cable 1 Screw kit 1 VGA cable 1 RS-232 cable Image For Touch Panel (T-R) Models only 1 TouchKit Driver CD 1 Touch pen Table 4-1: Packing List Page 19
RPC-6106/6108 Rackmount LCD Workstation 4.3 Pre-installation Preparation 4.3.1 System Planning User supplied CPU cards and backplanes or motherboards need to be installed in the system before installing the RPC-6106/6108 Rackmount LCD Workstation.
RPC-6106/6108 Rackmount LCD Workstation 4.3.2 Tools Before installing the RPC-6106/6108 Rackmount LCD Workstation, make sure the following tools are on hand: Phillips (crosshead) screwdriver: All the retention screws on the system are Phillips screws. Soft working mat: When installing the RPC-6106/6108 Rackmount LCD Workstation, the screen should be placed face down on a soft working mat. 4.4 Installation Procedures 4.4.
RPC-6106/6108 Rackmount LCD Workstation 4.4.3 Installation Steps Complete the following steps to properly install the workstation: Step 1: Open the top cover. Step 2: Remove the disk drive bracket. Step 3: Install the disk drives. Step 4: Reinstall the disk drive bracket with the installed disk drives. Step 5: Install the backplane. Step 6: Install the CPU card. Step 7: Install the PCI or ISA expansion cards (optional). Step 8: Connect all required cables. Step 9: Close the top cover.
RPC-6106/6108 Rackmount LCD Workstation WARNING: Failure to follow the installation procedures outlined in this section may cause severe damage to the RPC-6106/6108 Rackmount LCD Workstation. Please follow the installation instructions carefully. 4.5.1 Remove the Top Cover The top cover is secured to the RPC-6106/6108 Rackmount LCD Workstation with six screws (three each on the left and right panels). To remove the top cover, please follow the steps below.
RPC-6106/6108 Rackmount LCD Workstation Step 2: Slide the top cover toward the rear panel to remove (Figure 4-2). Step 0: Figure 4-2: Remove the Top Cover from the Chassis 4.5.2 Remove the Drive Bracket The drive bracket is secured to the RPC-6106/6108 Rackmount LCD Workstation with four retention screws inside the base of the chassis. To remove the drive bracket, please follow the steps below.
RPC-6106/6108 Rackmount LCD Workstation Figure 4-3: Drive Bracket Retention Screws Step 2: Remove the drive bracket from the chassis.Step 0: 4.5.3 Install Drives The drive bracket supports two 3.5” disk drives. To install disk drives, follow the instructions below. Step 1: Remove the drive bracket from the RPC-6106/6108 Rackmount LCD Workstation (see Section 4.5.3). Step 2: Slide the disk drive into the drive bracket.
RPC-6106/6108 Rackmount LCD Workstation 4.5.4 Reinstall the Drive Brackets After the drives have been installed, reinstall the drive brackets into the chassis. NOTE: It might be easier to connect the disk drive IDE/SATA connectors to the ribbon cables and the disk drive power connectors to the PSU before the drive brackets are reinstalled into the chassis. Step 1: Remount the drive brackets in the original position they were removed from.
RPC-6106/6108 Rackmount LCD Workstation 4.5.5 Install the Backplane To install a backplane, follow the instructions below. Step 1: Install the correct amount of copper pillars (Figure 4-4) into the base of the chassis. NOTE: The backplane shown in Figure 4-4 is an example for reference only. The location and number of copper pillars depends on the backplane being used.
RPC-6106/6108 Rackmount LCD Workstation Step 2: Mount the backplane into the chassis. Make sure the backplane is positioned so that when the CPU card and PCI/ISA expansion cards are installed, both the CPU card and the PCI/ISA card I/O connectors face the I/O brackets on the front panel. Step 3: Align the retention screw holes in the backplane with the copper pillars installed in Step 1. Step 4: Insert retention screws to secure the backplane to the chassis (Figure 4-5).
RPC-6106/6108 Rackmount LCD Workstation CAUTION: Depending on the location of the CPU card, the disk drive ribbon cable connectors and other peripheral device cable connectors may have to be connected to the CPU card before it can be installed. To install a CPU card onto the backplane, follow the instructions below: Step 1: Remove the slot cover retention screw to remove the slot bracket from the chassis rear panel (Figure 4-6).
RPC-6106/6108 Rackmount LCD Workstation Figure 4-7: Install the CPU Card Step 3: To secure the CPU card, reinsert the previously removed slot cover retention screw.Step 0: 4.5.7 Install the PCI/ISA Expansion Card To install a PCI expansion card or an ISA expansion card please follow the instructions below. Step 1: Remove the slot cover retention screw to remove the slot bracket from the chassis rear panel (Figure 4-6).
RPC-6106/6108 Rackmount LCD Workstation PSU cables Disk drive ribbon cables RS-232 cable (T-R models only) Other connections may have to be made; please refer to the documentation that came with the CPU card. 4.5.8.1 VGA Cable To monitor the system on the LCD on the front panel, use the VGA cable in the package to connect the AD board and the VGA connector on the external interface of the CPU card. Follow the steps below to connect the VGA cable.
RPC-6106/6108 Rackmount LCD Workstation Figure 4-9: VGA Connector on the Front Panel Step 4: Connect the VGA cable to the VGA connector on the CPU card. Replace the cable window cover (Figure 4-10).
RPC-6106/6108 Rackmount LCD Workstation 4.5.8.2 PSU Cables PSU cables must be connected to the following components (if installed): CPU card Backplane HDD Optical drive 4.5.8.3 Disk Drive Ribbon Cables Disk drive ribbon cables must be connected to the corresponding CPU card disk drive connectors. 4.5.8.
RPC-6106/6108 Rackmount LCD Workstation 4.5.
RPC-6106/6108 Rackmount LCD Workstation instructions when mounting the workstation. To rack mount the workstation, please follow the steps below. Step 1: The left and right side panels of the workstation each have four screw holes for rack handle bracket installation. Assemble the rack handle brackets and secure them to the workstation. (See Figure 4-12) Figure 4-12: Rack Handle Bracket Assembly and Installation Step 2: Attach the slide brackets to the rack per the manufacturer’s instructions.
RPC-6106/6108 Rackmount LCD Workstation Figure 4-13: Rack Slide Bracket Installation Page 36
RPC-6106/6108 Rackmount LCD Workstation Step 3: Insert the workstation into the rack slide brackets until the handle brackets are flush against the rack.
RPC-6106/6108 Rackmount LCD Workstation Step 4: Secure the workstation handle brackets to the rack with the fasteners that came with the workstation.
RPC-6106/6108 Rackmount LCD Workstation Chapter 5 5 Maintenance Page 39
RPC-6106/6108 Rackmount LCD Workstation 5.1 Maintenance Overview Maintaining the RPC-6106/6108 Rackmount LCD Workstation is essential for the smooth operation of system applications. Maintaining the system might mean replacing failed components during the lifetime of the workstation. The following RPC-6106/6108 components can be replaced. CPU card PCI/ISA expansion card Backplane Power supply unit (PSU) Cooling fans 3.
RPC-6106/6108 Rackmount LCD Workstation 5.2 CPU Card Replacement To replace a CPU card, please follow the instructions below. Step 1: Turn off and disconnect the workstation from all power sources. Step 2: Remove the workstation from the rack in which it is installed. Step 3: Open the top cover of the RPC-6106/6108 Rackmount LCD Workstation. (See Section 4.5.1) Step 4: Disconnect all internal and external peripheral device connections from the CPU card.
RPC-6106/6108 Rackmount LCD Workstation Step 4: Disconnect all internal and external peripheral device connections from the PCI/ISA expansion card. Step 5: Remove the retention screw that secures the CPU card to the slot on the rear panel. Step 6: Slide the expansion card out of the workstation. Step 7: Install a new expansion card. (See Section 4.5.7) Step 8: Insert the slot retention screw that was removed earlier. Step 9: Reinstall the top cover of the workstation. (See Section 4.5.
RPC-6106/6108 Rackmount LCD Workstation Step 9: Close the back cover of the workstation and reinstall the workstation into the cabinet or rack in which it was previously installed. Refer to Section 4.6 for complete mounting instructions. Step 0: 5.5 PSU Replacement To replace a PSU, please follow the instructions below. Step 1: Turn off and disconnect the workstation from all power sources. Step 2: Remove the workstation from the rack in which it is installed.
RPC-6106/6108 Rackmount LCD Workstation Step 6: Remove the two internal retention screws that secure the PSU assembly to the left side panel of the workstation (Figure 5-2). Figure 5-2: PSU Internal Retention Screws Step 7: Install the new PSU into the workstation making sure the PSU power connector and PSU cooling fan are facing out of the workstation. Step 8: Reinsert the two previously removed internal retention screws that secure the PSU assembly to the left side panel of the workstation.
RPC-6106/6108 Rackmount LCD Workstation CAUTION: Carefully note the direction and orientation of the existing system fan prior to replacement. Step 1: Turn off and disconnect the workstation from all power sources. Step 2: Remove the workstation from the rack in which it is installed. Step 3: Loosen the fan filter bracket thumbscrews on the rear panel (Figure 5-4). Figure 5-3: System Fan Retention Thumbscrews Step 4: Disconnect the system fan from the PSU.
RPC-6106/6108 Rackmount LCD Workstation to secure the fan to the fan bracket. Step 7: Connect the new system fan to the PSU. Step 8: Reinstall the fan bracket and fasten the thumbscrews.Step 0: 5.7 Disk Drive Replacement 5.7.1 3.5” Disk Drive To replace a disk drive, please follow the instructions below. Step 1: Turn off and disconnect the workstation from all power sources. Step 2: Remove the workstation from the rack in which it is installed.
RPC-6106/6108 Rackmount LCD Workstation Chapter 6 6 On Screen Display (OSD) Controls Page 47
RPC-6106/6108 Rackmount LCD Workstation 6.1 User Mode OSD Structure 6.1.1 OSD Buttons There are several on-screen-display (OSD) control buttons oriented either vertically (RPC-6106) or horizontally (RPC-6108) on the front panel of the workstation. Figure 6-1 shows a typical arrangement of OSD controls. Figure 6-1: OSD Control Buttons NOTE: Pressing the direction keys (LEFT or RIGHT) can bring out a simple menu that adjusts the LCD screen brightness and contrast values.
RPC-6106/6108 Rackmount LCD Workstation 6.1.2 OSD Menu Structure Table 6-1 shows the OSD menu structure. Level 0 Level 1 Value Main Display Features Menu Brightness 0 to 100 Contrast 0 to 100 Horizontal Size 0 to 100 Phase 0 to 100 H. Position 0 to 100 V. Position 0 to 100 Sharpness 1 to 5 Volume This menu is currently disabled, Mute and will be implemented with Speaker models equipped with speakers.
RPC-6106/6108 Rackmount LCD Workstation Level 0 Level 1 Value Signal Menu Digital Select Analog Backlight Menu Light Enable On or Off Light Contrast 0 to 100 Light Brightness 0 to 100 Light H Start 0 to 100 Light H Width 0 to 100 Light V Start 0 to 100 Light V Height 0 to 100 Table 6-1: OSD Menus 6.2 Using the OSD OSD menu options are described below. 6.2.1 Main Display Features Main display features are shown in Figure 6-2.
RPC-6106/6108 Rackmount LCD Workstation Brightness: The brightness option adjusts the brightness of screen. This function adjusts the offset value of ADC. Setting this value too high or too low will affect the quality of image. Contrast: This function adjusts the gain value of ADC. Adjusting this value too high or too low will worsen the quality of image. Horizontal Size: This item adjusts the screen size in the horizontal direction.
RPC-6106/6108 Rackmount LCD Workstation The Color menu fine-tunes the palette of color hues for the LCD. 9300: NTSC standard Kelvin 7500: NTSC standard Kelvin 6500: NTSC standard Kelvin User: This item allows fine-tuning the balance among Red, Green, and Blue color hues if images look garish or unrealistic. 6.2.3 Language The Languages are shown in Figure 6-4. Figure 6-4: Language Menu This menu provides options for selecting ODS screen legends in a preferred language.
RPC-6106/6108 Rackmount LCD Workstation 6.2.4 OSD Configurations The OSD configurations are shown in Figure 6-5. Figure 6-5: OSD Configurations Menu OSD Configurations are described below. OSD Time Out: Determines how many seconds the OSD screen stays on screen before it disappears when OSD is left unattended. OSD Position: Adjusts the OSD position on the screen. Position 1 is in the upper left of the screen, position 2 in the upper right and position 3 in the center.
RPC-6106/6108 Rackmount LCD Workstation Aspect Ratio Adjusts the display ratio referring to the width of the screen and then to the height of the screen. 6.2.5 Signal The Signal menu in Figure 6-6 enables manual selection of the type of graphic source input, i.e., analog (15-pin VGA) or digital (DVI-D).
RPC-6106/6108 Rackmount LCD Workstation 6.2.6 Backlight The Backlight menu in Figure 6-7 enables users to configure the LCD backlight. Figure 6-7: Backlight Menu Backlight Menu options are described below. Light Enabled: Turns backlight on or off. Light Contrast: Adjusts the backlight contrast. Light Brightness: Adjusts the backlight brightness. Light H Start: Adjusts the backlight projection area in the horizontal direction. Light H Width: Adjusts the width of the backlight projection area.
RPC-6106/6108 Rackmount LCD Workstation THIS PAGE IS INTENTIONALLY LEFT BLANK Page 56
RPC-6106/6108 Rackmount LCD Workstation Chapter 7 7 Software Driver Page 57
RPC-6106/6108 Rackmount LCD Workstation NOTE: The following information is provided for workstations with touch screens. 7.1 Touch Screen Driver The touch screen controller enables analog resistive touch screens for four-wire, five-wire & eight-wire models. The controller directly communicates with the PC system through the touch screen communications interface. The controller design is superior in sensitivity, accuracy, and friendly operation.
RPC-6106/6108 Rackmount LCD Workstation 7.2 Driver Installation To install the touch screen software driver, please follow the steps below. Step 1: Insert the TouchKit driver CD that came with the RPC-6106/6108 rackmount workstation into the CD drive. Step 2: Once the CD drive is installed, the screen in Figure 7-1 appears. Figure 7-1: Driver CD Pop Up Screen Step 3: Select the operating system installed on the system from the menu on the left side of the screen.
RPC-6106/6108 Rackmount LCD Workstation Step 4: Once the OS system is selected, the touch kit setup will prepare the install shield wizard (Figure 7-2). Figure 7-2: Install Shield Wizard Preparation Step 5: After the Install Shield Wizard is ready, a welcome screen appears (Figure 7-3). Figure 7-3: Welcome Screen Step 6: To continue the installation process click NEXT.
RPC-6106/6108 Rackmount LCD Workstation Step 7: An Install PS/2 interface driver screen appears (Figure 7-4). It is not necessary to install the PS/2 interface driver. To continue click NEXT.
RPC-6106/6108 Rackmount LCD Workstation Step 8: Four point calibration options are then selected (Figure 7-5). Four point calibrations can be done every time a user boots up, during the next time the system boots or never. Select if and when a four-point calibration should be done. Click NEXT to continue.
RPC-6106/6108 Rackmount LCD Workstation Step 9: The user is then prompted to ensure the touch monitor or the USB for the touch controller is plugged into the system (Figure 7-6). Once the touch controller is plugged into the system, click “OK.” Figure 7-6: Touch Monitor/USB Touch Controller Confirmation Step 10: The user is then prompted to select multi-monitor system support (Figure 6-7). Make the appropriate selection and click NEXT to continue.
RPC-6106/6108 Rackmount LCD Workstation Step 11: The user is then prompted to select a file directory in which the touch kit controller is installed (Figure 7-8). The default directory is “C:\Program Files\TouchKit.” If a different folder must be used, select browse and then select the folder. Once the folder is selected, click NEXT to continue.
RPC-6106/6108 Rackmount LCD Workstation Step 12: The user is then prompted to select a file directory in which the program icons are saved (Figure 7-9). The default folder is “TouchKit.” If a different folder must be used, select a folder from the list shown. Once the folder is selected, click NEXT to continue.
RPC-6106/6108 Rackmount LCD Workstation Step 13: The program then starts installing (Figure 7-10).
RPC-6106/6108 Rackmount LCD Workstation Step 14: Once the program is finished installing, the user is prompted to restart the computer now or to restart the computer later (Figure 7-11). Select when the computer should be restarted and click “FINISH” to complete the driver installation procedure.Step 0: Figure 7-11: Installation Complete 7.3 Touch Panel Driver Configuration To configure the touch screen driver options, refer to the TouchKit user manual located on the driver installation CD.
RPC-6106/6108 Rackmount LCD Workstation THIS PAGE IS INTENTIONALLY LEFT BLANK Page 68
RPC-6106/6108 Rackmount LCD Workstation Appendix A A Certification Page 69
RPC-6106/6108 Rackmount LCD Workstation A.1 RoHS Compliant All RPC-6106/6108 rackmount workstations comply with the Restriction of Hazardous Materials (RoHS) Directive. This means that all components used to build the industrial workstations and the workstation itself are RoHS compliant.
RPC-6106/6108 Rackmount LCD Workstation Appendix B B Recommended IEI Backplanes and PSUs Page 71
RPC-6106/6108 Rackmount LCD Workstation The following IEI backplanes and power supply options are recommended for the RPC-6106/6108 Rackmount LCD Workstation. For more information about these backplanes and power supply units, please contact an IEI sales representative or visit the IEI website (www.ieiworld.com). B.1 RPC-6106/6108 Backplane Options Table B-1 shows the backplane options for RPC-6106/6108. PCIe Model No.
RPC-6106/6108 Rackmount LCD Workstation C Index Page 73
RPC-6106/6108 Rackmount LCD Workstation A I Analog VGA .................................................2 Install the Backplane..................................27 Install the CPU Card ..................................28 B Backplane Options.....................................72 Backplane Replacement............................42 Install the PCI/ISA Expansion Card ...........30 Installation Considerations.........................16 Internal overview..........................................
RPC-6106/6108 Rackmount LCD Workstation PCI/ISA Expansion Card Replacement .....41 S Physical Dimensions..........................8, 9, 10 Power LED...................................................6 slot cover retention screw ................... 29, 30 Power Supply Options ...............................72 Specifications Power switch..........................................6, 12 LCD Specifications ................................13 Pre-installation Preparation .......................
