PPC-5xxx-9455 Panel PC IEI Technology Corp. MODEL: PPC-5xxx-9455 Industrial Panel PC for LGA775 Intel™ Core®2 Duo TFT LCD, Dual Gigabit Ethernet, Touch Screen RoHS Compliant, IP 65 Protection User Manual Page i Rev. 1.
PPC-5xxx-9455 Panel PC Revision Date Version Changes 28 September, 2012 1.10 Updated Section 1.1.1: Model Variations Updated Section 2.1.4: Power Supply Changed Ethernet controller from Broadcom BCM5787M to Realtek RTL8111CP 9 March, 2011 1.01 Added Section 4.5.6.5 COM5 RS-422 and RS-485 Pinouts August, 2008 1.
PPC-5xxx-9455 Panel PC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PPC-5xxx-9455 Panel PC Manual Conventions WARNING! Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. Warnings are easy to recognize. The word “warning” is written as “WARNING,” both capitalized and bold and is followed by text. The text is the warning message. A warning message is shown below: WARNING: This is an example of a warning message.
PPC-5xxx-9455 Panel PC NOTE: These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes. Notes are easy to recognize. The word “note” is written as “NOTE,” both capitalized and bold and is followed by text. The text is the cautionary message. A note message is shown below: NOTE: This is an example of a note message. Notes should always be read.
PPC-5xxx-9455 Panel PC Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the PPC-5xxx-9455 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the PPC-5xxx-9455 package.
PPC-5xxx-9455 Panel PC Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 GENERAL OVERVIEW ................................................................................................. 2 1.1.1 Model Variations ................................................................................................ 3 1.1.2 Applications .....................................................................................
PPC-5xxx-9455 Panel PC 2.4 CPU SUPPORT .......................................................................................................... 23 2.5 SYSTEM CHIPSETS .................................................................................................... 23 2.5.1 Intel® 945G Northbridge Chipset ................................................................... 24 2.5.2 ICH7 Southbridge Chipset............................................................................... 24 2.
PPC-5xxx-9455 Panel PC 4.5.3 Monitor Setup (JP1)......................................................................................... 44 4.5.4 CF Card Setup (JP7)........................................................................................ 45 4.5.5 COM Port RI and Voltage Selection (JP3, JP4, JP5, JP6, JP8) ..................... 45 4.5.6 COM5 RS-232/422/485 Settings ...................................................................... 46 4.5.6.1 COM5 RS-232/422/485 RX Select (J2) ...........
PPC-5xxx-9455 Panel PC 5.1.5 BIOS Menu Bar................................................................................................ 71 5.2 MAIN........................................................................................................................ 72 5.3 ADVANCED ............................................................................................................... 73 5.3.1 CPU Configuration.......................................................................................
PPC-5xxx-9455 Panel PC 6.6 TOUCH PANEL DRIVER ........................................................................................... 139 7 SYSTEM MAINTENANCE ..................................................................................... 144 7.1 SYSTEM MAINTENANCE INTRODUCTION ................................................................ 145 7.2 MOTHERBOARD REPLACEMENT ............................................................................. 145 7.3 BACK COVER REMOVAL .....................
PPC-5xxx-9455 Panel PC G HAZARDOUS MATERIALS DISCLOSURE ....................................................... 177 G.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY .....................................
PPC-5xxx-9455 Panel PC List of Figures Figure 1-1: PPC-5xxx-9455 ............................................................................................................2 Figure 1-2: Front View ....................................................................................................................4 Figure 1-3: PPC-5xxx-9455 Rear View ..........................................................................................5 Figure 1-4: PPC-5xxx-9455 Top View.................................
PPC-5xxx-9455 Panel PC Figure 4-11: Optical Drive Blank Plate Assembly .....................................................................54 Figure 4-12: Optical Drive Screws ..............................................................................................55 Figure 4-13: Optical Drive SATA Cable ......................................................................................56 Figure 4-14: Optical Drive Bracket Screws .....................................................................
PPC-5xxx-9455 Panel PC Figure 6-20: Hardware Installation Complete ......................................................................... 137 Figure 6-21: Select the Audio Codec ....................................................................................... 138 Figure 6-22: Audio Driver Installation...................................................................................... 138 Figure 6-23: InstallShield Wizard Complete....................................................................
PPC-5xxx-9455 Panel PC List of Tables Table 1-1: PPC-5xxx-9455 Model Variations ................................................................................3 Table 2-1: PPC-5xxx-9455 Specifications ..................................................................................12 Table 2-2: Motherboard Specifications ......................................................................................13 Table 2-3: 15” TFT LCD Monitor Specifications ...................................................
PPC-5xxx-9455 Panel PC BIOS Menus BIOS Menu 1: Main .......................................................................................................................72 BIOS Menu 2: Advanced ..............................................................................................................74 BIOS Menu 3: CPU Configuration ...............................................................................................75 BIOS Menu 4: IDE Configuration...........................................
PPC-5xxx-9455 Panel PC Chapter 1 1 Introduction Page 1
PPC-5xxx-9455 Panel PC 1.1 General Overview Figure 1-1: PPC-5xxx-9455 The PPC-5xxx-9455 flat panel PC is for industrial environments like production lines and machine automation. The PPC-5xxx-9455 provides all the features of a PC, combined with a touch panel screen for mouse and keyboard free data input. The PPC-5xxx-9455 provides wired and, optionally, wireless networking for integration into company networks. All major external device connections including USB, serial and parallel port connectors.
PPC-5xxx-9455 Panel PC 1.1.1 Model Variations Four IEI PPC-5xxx-9455 models are available. The models are listed in Table 1-1. Socket / Model CPU PPC-5150A-R11/9455-E2160/A618A/T-R/1GB PPC-5150A-R11/9455-E2160/4520C/T-R/1GB PPC-5170A-R11/9455-E2160/A622A/T-R/1GB PPC-5170A-R11/9455-E2160/4520C/T-R/1GB PPC-5190A-R11/9455-E2160/A622A/T-R/1GB LGA775 1.
PPC-5xxx-9455 Panel PC High brightness industrial grade LCD panel The following I/O ports o o o o o o 5 x COM (1 for Touch Screen) 4 x USB 2.0 ports 1 x PCI slot 1 x CompactFlash® slot 1 x VGA port 1 x Parallel port Dual 10/100/Gigabit Ethernet supported RoHS compliant 1.2 External Overview The PPC-5xxx-9455 flat panel PC is comprised of an LCD screen, aluminum front panel and heavy duty steel rear and side panels. The rear panel provides screw holes for wall and an arm mounting.
PPC-5xxx-9455 Panel PC 1.2.2 Rear Panel The rear panel has a fan vent, four VESA standard mounting holes and several retention screw holes. The VESA mounting holes are circled in Figure 1-3. Figure 1-3: PPC-5xxx-9455 Rear View 1.2.3 Top Panel The top panel has two fan vents, eight mounting clamp slots and three retention screws for securing the drive bay bracket. The retention screws are circled in Figure 1-4 below.
PPC-5xxx-9455 Panel PC 1.2.
PPC-5xxx-9455 Panel PC 1.2.5 Left Panel The left side panel has two fan vents and four retention screws for securing the two internal fans. The retention screws are circled in Figure 1-6. Figure 1-6: Left View 1.2.6 Right Panel The right side panel provides access to a slim type CD drive bay and a FDD drive bay shown in Figure 1-7.
PPC-5xxx-9455 Panel PC 1.3 Internal Overview The PPC-5xxx-9455 internal components are configured in three levels. The PSU cover bracket to the left (Figure 1-8) supports the hard drive and optical drive brackets. Below the PSU cover bracket is the power supply. On the same level as the power supply is the motherboard. Below the motherboard and PSU level is an LCD panel. An overview picture of the internal components is shown in Figure 1-8 below.
PPC-5xxx-9455 Panel PC Chapter 2 2 Specifications Page 9
PPC-5xxx-9455 Panel PC 2.1 Introduction The PPC-5xxx-9455 flat panel PC has the following preinstalled components: 1 x Motherboard 1 x TFT LCD screen 1 x Power supply 2 x Cooling fans The technical specifications for these components and the system are shown in the sections below. 2.1.1 System Specifications The technical specifications for the PPC-5xxx-9455 system are listed in Table 2-1.
PPC-5xxx-9455 Panel PC SPECIFICATION DESCRIPTION Touch Screen Optional 5-wire resistive type touch screen with RS-232 interface Display Supports Dual Display Add-On Card (Optional) One PCI card Drive Bay One 2.5” HDD bay with anti-shock One slim type CD drive bay One slim type FDD bay One CompactFlash® slot Power Supply Input voltage: 90~265 V AC, 50~60 Hz Output rating: 180 W Output voltage: +3.3 V @ 16.8A +5 V @ 12A +12 V @ 10A -12 V @ 0.
PPC-5xxx-9455 Panel PC SPECIFICATION DESCRIPTION Shock 10G Acceleration, peak to peak (11ms) Dimensions (W x D x H) PPC-5150A-9455: 410 mm x 309 mm x 110.5 mm PPC-5170A-9455: 452 mm x 356 mm x 115 mm PPC-5190A-9455: 483 mm x 399 mm x 115.2 mm Net/Gross Weight PPC-5150A-9455: 7 kg/11 kg PPC-5170A-9455: 8 kg/12 kg PPC-5190A-9455: 12.6 kg/18.2 kg Environment RoHS Compliant Table 2-1: PPC-5xxx-9455 Specifications 2.1.2 Motherboard Specifications The PPC-5xxx-9455 comes with a POS-9455 motherboard.
PPC-5xxx-9455 Panel PC SPECIFICATION DESCRIPTION Ethernet 2 x Realteck RTL8111CP GbE controller COM 1 x RS-232/422/485 port 5 x RS-232 ports (1 used internally for touch screen) USB 2.0 6 x USB 2.0 ports Drive Interfaces 2 x SATA drive connectors LPT 1 x Parallel port KB/ MS 2 x PS/2 connector IrDA 1 x IrDA interface Table 2-2: Motherboard Specifications 2.1.3 Flat Panel Screen The PPC-5xxx-9455 comes with a flat panel TFT LCD screen. Screen specifications for each model are detailed below.
PPC-5xxx-9455 Panel PC SPECIFICATION DETAILS Brightness (cd/m2) 350 Contrast Ratio 400:1 Response Time (ms) (at 25°C) 16 Power Consumption (W) 11.5 Interface 1ch LVDS Supply Voltage (V) 3.3 Backlight 2 CCFL Outline Dimensions (mm) 326.5 x 253.5 x 12.0 Weight (g) 1100 Table 2-3: 15” TFT LCD Monitor Specifications 2.1.3.2 PPC-5170A-9455 Screen The PPC-5170A-9455 comes with a 17” TFT LCD monitor at the front of the flat panel PC.
PPC-5xxx-9455 Panel PC SPECIFICATION DETAILS Response Time (ms) (at 25°C) 8 Power Consumption (W) 25.8 Interface 2ch LVDS Supply Voltage (V) 5 Backlight 4 CCFL Outline Dimensions (mm) 358.5 x 296.5 x 17.0 Weight (g) 1900 Table 2-4: 17” TFT LCD Monitor Specifications 2.1.3.3 PPC-5190A-9455 Screen The PPC-5190A-9455 comes with a 19” TFT LCD monitor at the front of the flat panel PC. The specifications for the LCD monitor are shown in Table 2-5 below.
PPC-5xxx-9455 Panel PC SPECIFICATION DESCRIPTION Interface 2ch LVDS Supply Voltage (V) 5 Backlight 4 CCFL Outline Dimensions (mm) 396.0 x 324.0 x 17.5 Weight (g) 2500 Table 2-5: 19” TFT LCD Monitor Specifications 2.1.4 Power Supply The PPC-5xxx-9455 flat panel PC comes with either an ACE-A618A 180 W 1U, ACE-4520C 200 W DC 1U or ACE-A622A 220 W 1 U RoHS compliant ATX power supply. The PSUs have an MTBF greater than 100,000 hours. WARNING: Under no circumstances is the PSU case to be opened.
PPC-5xxx-9455 Panel PC 2.1.4.1 ACE-A618A Power Supply Specifications for the ACE-A618A PSU module are shown in (Table 2-6). Specification Rating INPUT Voltage 90 V ~ 264 VAC Full Range OUTPUT Voltage (V) +3.3 V +5 V +12 V -12 V 5 VSB Min. Load (A) 0.3A 0.3A 1.5A 0A 0A Max. Load (A) 14A 16A 14A 0.
PPC-5xxx-9455 Panel PC Specification OUTPUT Rating Voltage (V) +3.3 V +5 V +12 V -12 V 5 VSB Min. Load (A) 0.0A 1.0A 0.5A 0.0A 0.0A Max. Load (A) 12A 12A 15.4A 0.5A 2.0A Ripple and Noise (mV) 50mV 50mV 120mV 120mV 50mV +3.3 V & +5 V≦80 W; +3.
PPC-5xxx-9455 Panel PC 2.1.4.3 ACE-A622A Power Supply Specifications for the ACE-A622A PSU module are shown in (Table 2-8). Specification Rating INPUT Voltage 90 V ~ 264 VAC Full Range OUTPUT Voltage (V) +3.3 V +5 V +12 V -5 V -12 V 5 VSB Min. Load (A) 0.5A 0.5A 1A 1A 0A 0A Max. Load (A) 14A 16A 16A 10A 0.8A 2.
PPC-5xxx-9455 Panel PC 2.2.1 PPC-5150A-9455 Dimensions The dimensions of the PPC-5150A-9455 flat panel PC are shown in Figure 2-1 below.
PPC-5xxx-9455 Panel PC 2.2.2 PPC-5170A-9455 Dimensions The dimensions of the PPC-5170A-9455 flat panel PC are shown in Figure 2-2 below.
PPC-5xxx-9455 Panel PC 2.2.3 PPC-5190A-9455 Dimensions The dimensions of the PPC-5190A-9455 flat panel PC are shown in Figure 2-3 below.
PPC-5xxx-9455 Panel PC 2.3 Motherboard The PPC-5xxx-9455 flat screen PC contains a POS-9455 motherboard. The motherboard is the heart of any computer and is responsible for transmitting, receiving and processing data as well as driving the different on-board devices. This chapter gives a brief introduction to the POS-9455 motherboard. For more complete details on the connectors and the different implementations of the POS-9455, please refer to the POS-9455 user manual. Figure 2-4: POS-9455 Motherboard 2.
PPC-5xxx-9455 Panel PC Specifications of these two chipsets are listed in the subsections below. 2.5.
PPC-5xxx-9455 Panel PC Integrated Serial ATA Host Controllers o o Data transfer rates up to 1.5 Gb/s (150 MB/s). Integrated IDE Controller o o o o Independent DMA operation on two ports. Supports “Native Mode” Register and Interrupts Independent timing of up to 4 drives Ultra ATA/100/66/33, BMIDE and PIO modes Tri-state modes to enable swap bay Interrupt Controller o o o o o Supports up to 8 PCI interrupt pins Supports PCI 2.
PPC-5xxx-9455 Panel PC 2.6.1 Analog CRT Support The VGA port connects a peripheral monitor to the PPC-5xxx-9455 system. A DB-15 VGA connector on the external peripheral interface connector panel is interfaced to the Intel® 945G Northbridge. The Intel® 945G supports analog CRT monitors with the following features: Supports max DAC frequency up to 400 MHz 24-bit RAMDAC support DDC2B compliant Up to 2048 x 1536 mode support 2.6.2 LVDS Support The LVDS connector drives the built-in LCD panel.
PPC-5xxx-9455 Panel PC Figure 2-5: SO-DIMM Socket 2.8 Storage There following storage options are available: CompactFlash® SATA hard drive 2.8.1 CompactFlash® The CompactFlash® socket supports standard CompactFlash® Type I and CompactFlash® Type II cards. The chipset flash interface is multiplexed with an IDE interface and can be connected to an array of industry standard NAND Flash or NOR Flash devices. The CompactFlash® slot location is shown below.
PPC-5xxx-9455 Panel PC Figure 2-6: CompactFlash® Slot 2.8.2 SATA Hard Drive The integrated SATA controller supports two SATA drives with independent DMA operations. One SATA port is implemented internally for the internal 2.5” SATA hard drive. The second SATA port is implemented on the external connector panel through an eSATA connector. SATA controller specifications are listed below. Page 28 Supports two SATA drives Supports 3.
PPC-5xxx-9455 Panel PC Figure 2-7: SATA Hard Drive Slot 2.9 Expansion Slots The PPC-5xxx-9455 includes either a PCI or PCIe x4 expansion card slot. The expansion card slots add additional functionality to the PPC-5xxx-9455.
PPC-5xxx-9455 Panel PC Ethernet adapter cards Modem cards Sound cards PCIe x4 cards available for the PPC-5xxx-9455 include: Gigabit Ethernet adapter cards SATA 3.0Gb/s or RAID controller cards TV tuner cards Graphics cards Firewire & USB cards 2.10 External Device Connectors The external device connectors allow external components to be attached to the PPC-5xxx-9455. The external communications device connectors are shown in the sections below. 2.10.1 USB 2.
PPC-5xxx-9455 Panel PC 2.10.2 Serial Ports Serial ports provide communications to external devices. Four of the external serial ports provide short-range communications, while one provides for longer range communication. Figure 2-10: Serial Ports Some features of the serial ports include: RS-232 transmission protocol for easy connection to devices with a standard RS-232 interface RS-422 and RS-485 transmission capabilities for longer distance connections. 2.10.
PPC-5xxx-9455 Panel PC Standard setup connects to devices with a standard parallel port, like printers 2.11 Gigabit Ethernet The Realtek RTL8111CP PCI Express (PCIe) GbE controller is a 10/100/1000BASE-T Ethernet LAN controller. The RTL8111CP combines a triple-speed IEEE 802.3 compliant Media Access Controller (MAC) with a triple-speed Ethernet transceiver, a PCIe bus interface, and an embedded memory.
PPC-5xxx-9455 Panel PC Pixel pitch of 0.297 mm or less 700:1 contrast ratio or better 300 cd/m2 or greater 8 msec optical response time or less 0oC to 50oC operating temperature 2.12.2 Touch Screen The touch screen panel on the PPC-5xxx-9455 allows complete user interaction without the need for a keyboard or mouse. Some of the features of the touch panel are listed below.
PPC-5xxx-9455 Panel PC Chapter 3 3 Unpacking Page 34
PPC-5xxx-9455 Panel PC 3.1 Anti-static Precautions WARNING! Failure to take ESD precautions during the installation of the PPC-5xxx-9455 may result in permanent damage to the PPC-5xxx-9455 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the PPC-5xxx-9455. Dry climates are especially susceptible to ESD.
PPC-5xxx-9455 Panel PC 3.3 Package Contents NOTE: If any components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the PPC-5xxx-9455 was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw.
PPC-5xxx-9455 Panel PC Quantity Item and Part Number 1 Screw set 1 IDE adapter Image (for slim CD-ROM) 1 User manual CD and driver CD 1 Touch pen Table 3-1: Package List Contents Page 37
PPC-5xxx-9455 Panel PC Chapter 4 4 Installation and Configuration Page 38
PPC-5xxx-9455 Panel PC 4.1 Installation Precautions When installing the PPC-5xxx-9455, please follow the precautions listed below: Turn power off: When installing the PPC-5xxx-9455 make sure the power is off. Failing to turn off the power may cause severe injury to the body and/or damage to the system. Certified Engineers: Only certified engineers should install and modify on-board functions. Mounting: The PPC-5xxx-9455 is a heavy device.
PPC-5xxx-9455 Panel PC 4.3 Installation and Configuration Steps The following installation steps must be followed. Step 1: Unpack the PPC-5xxx-9455. Step 2: Set the jumper settings. Step 3: Install HDD, CompactFlash® and CD drive. Step 4: Mount the PPC-5xxx-9455 flat panel PC. Step 5: Connect peripheral devices to the bottom panel of the PPC-5xxx-9455. Step 6: Configure the system.
PPC-5xxx-9455 Panel PC 4.4 Remove the Back Cover Remove all the retention screws on the back cover. Lift the cover up to remove (Figure 4-1).
PPC-5xxx-9455 Panel PC 4.5 Jumper Settings NOTE: These jumper settings and the jumper locations are described in detail in the user manual that came with the POS-9455 motherboard. Please refer to the manual for more detailed descriptions of the jumper settings. NOTE: A jumper is a metal bridge that is used to close an electrical circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover that slides over the pins to connect them.
PPC-5xxx-9455 Panel PC Jumper Type Label COM5 D-SUB setup 12-pin header J4 COM5 termination resistor 2-pin header J5, J6 LCD voltage selection 6-pin header JP9 Touch screen selection 4-pin header J7 Table 4-1: Onboard Jumpers 4.5.1 AT/ATX Power Selection (AT_PWR_SW1) The AT/ATX power selection switch selects AT or ATX power for the PPC-5xxx-9455. ATX power has more power saving capabilities than AT power.
PPC-5xxx-9455 Panel PC JP2 DESCRIPTION 1-2 Normal (Default) 2-3 Clear CMOS Table 4-3: Clear CMOS Jumper Settings 4.5.3 Monitor Setup (JP1) WARNING: Do not change these settings. They are set for the installed LCD panel. Using different settings on the preinstalled monitor can destroy it. The monitor setup jumper sets the default settings for all monitors connected to the PPC-5xxx-9455. Pins 1-4 adjust the resolution of the screen.
PPC-5xxx-9455 Panel PC 4.5.4 CF Card Setup (JP7) The CF Card Setup jumper configures a CF card as either the IDE slave or IDE master. JP7 DESCRIPTION Open Slave Close Master Table 4-6: CF Card Setup Jumper Settings 4.5.5 COM Port RI and Voltage Selection (JP3, JP4, JP5, JP6, JP8) Use the COM port settings jumpers to select the voltage of serial port pin 9.
PPC-5xxx-9455 Panel PC JP6 COM4 Pin-9 Setting 1-2 12 V 3-4 RI 5-6 5V Table 4-10: COM4 RI and Voltage Selection Jumper JP8 COM5 Pin-9 Setting 1-2 12 V 3-4 RI 5-6 5V Table 4-11: COM5 RI and Voltage Selection Jumper 4.5.6 COM5 RS-232/422/485 Settings To enable RS-232, RS-422 or RS-485 on COM5, all the following jumpers should be setup. 4.5.6.1 COM5 RS-232/422/485 RX Select (J2) Jumper J2 sets the COM5 serial port as RS-232, RS-422 or RS-485.
PPC-5xxx-9455 Panel PC 4.5.6.3 COM5 D-Sub Pinout Selection (J4) Jumper J4 sets the external COM5 serial port as RS-232 or RS-422/485. J4 DESCRIPTION 1-2, 4-5, 7-8, 10-11 RS-232 2-3, 5-6, 8-9, 11-12 RS-422/485 Table 4-14: COM5 RS-422/485 TX Select 4.5.6.4 COM5 Termination Resistors (J5, J6) The termination resistors J5 and J6 can remedy communication errors for RS-422/485 setups with cables over 1.
PPC-5xxx-9455 Panel PC 4.5.7 LCD Voltage Settings (JP9) WARNING: Do not change these settings. They are set for the installed LCD panel. Using different settings on the preinstalled monitor can destroy it. The LCD setup sets the voltage and default monitor settings on the PPC-5xxx-9455. JP9 LCD Voltage 1-2 3.3 V 3-4 5V 5-6 12 V Table 4-18: LCD Voltage Settings 4.5.8 Touch Screen Selection (JP7) The touch screen selection jumper selects the type of touch screen panel connected to the system.
PPC-5xxx-9455 Panel PC 4.6.1 Hard Drive Installation To install a HDD, please follow the steps below: Step 1: Remove the back cover (Section 4.4). Step 2: The HDD bracket is attached to the elevated platform by four retention screws. Remove the four retention screws from the elevated platform (Figure 4-2). Figure 4-2: HDD Retention Screws Step 3: Attach the SATA connector cable to the bracket.
PPC-5xxx-9455 Panel PC Figure 4-3: HDD SATA Connector Step 4: Attach the hard drive in the bracket. To do this, slide the hard drive onto the bracket until it connects with the SATA connector at the back. Fasten the four retention screws on the side. Figure 4-4: HDD Retention Screws Step 5: Install the hard drive bracket (with hard drive and SATA cable attached) into the PPC-5xxx-9455 and fasten the four hard drive bracket screws.
PPC-5xxx-9455 Panel PC Figure 4-5: HDD Retention Screws 4.6.2 CompactFlash® Installation To install the CompactFlash® card, please follow the steps below: Step 1: Undo the CompactFlash® slot cover screw and remove the CompactFlash® cover plate.
PPC-5xxx-9455 Panel PC Step 2: Insert the CompactFlash® card into the slot. Figure 4-7: CompactFlash® Slot Step 3: Fasten the CompactFlash® cover plate.Step 0: Figure 4-8: CompactFlash® Cover Plate 4.6.3 CD Drive Installation To install a CD drive, please follow the steps below. Step 1: Remove the back cover (Section 4.4). Step 2: Attach the CD drive adapter to the CD-ROM if it is an IDE drive (if it is a SATA drive, proceed to Step 5:).
PPC-5xxx-9455 Panel PC Figure 4-9: CD Drive Adapter Installation Step 5: Undo the optical drive bracket screws and remove the optical drive bracket.
PPC-5xxx-9455 Panel PC Step 6: Remove the four screws from the optical drive bracket assembly. Remove the blank drive plate.
PPC-5xxx-9455 Panel PC Step 7: Install the optical drive in the same position as the previously removed blank optical drive plate. Fasten the same four screws to attach the optical drive to the bracket.
PPC-5xxx-9455 Panel PC Step 8: Attach the SATA cable to the back of the optical drive and fasten the SATA cable screws. Figure 4-13: Optical Drive SATA Cable Step 9: Reinstall the optical drive bracket into the PPC-5xxx-9455 and fasten the optical bracket screws.
PPC-5xxx-9455 Panel PC 4.7 Mounting the System WARNING! When mounting the PPC-5xxx-9455 flat panel PC onto an arm, wall or into a panel, it is advisable to have more than one person help with the installation to prevent accidental damage to the panel and avoid personal injury. The methods of mounting the PPC-5xxx-9455 are: Wall mounting Panel mounting Arm mounting Rack mounting The mounting methods are fully described below. 4.7.
PPC-5xxx-9455 Panel PC Figure 4-15: Wall-mounting Bracket Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the four screw holes on the real panel of the monitor and tighten until the screw shank is secured against the rear panel. Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket.
PPC-5xxx-9455 Panel PC Figure 4-16: Mount the Chassis Step 9: Secure the panel PC with the wall-mounting kit. To do this, stick the protective cushion to the wall-mounting kit first. Then, put the wall-mounting kit on the top panel of the panel PC. Carefully mark the location of the wall-mounting kit screw holes on the wall. Drill a pilot hole at the marked location on the wall. Secure the wall-mounting kit to the wall by inserting a retention screw into the pilot hole on the wall (Figure 4-17).
PPC-5xxx-9455 Panel PC Figure 4-17: Secure the Chassis 4.7.2 Panel/ Mounting To mount the PPC-5xxx-9455 flat panel PC into a panel, please follow the steps below. NOTE: The maximum panel thickness should be no more than 6 mm. Step 1: Select the position on the panel to mount the PPC-5xxx-9455. Step 2: Cut out a section of the panel that corresponds to the rear panel dimensions of the PPC-5xxx-9455. The recommended cutout sizes are shown below (Figure 4-18, Figure 4-19 and Figure 4-20).
PPC-5xxx-9455 Panel PC Figure 4-18: 15” Panel Cutout Dimensions Figure 4-19: 17” Panel Cutout Dimensions Page 61
PPC-5xxx-9455 Panel PC Figure 4-20: 19” Panel Cutout Dimensions Step 3: Slide the PPC-5xxx-9455 through the hole until the metal frame is flush against the panel. Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of the PPC-5xxx-9455, behind the metal frame (Figure 4-21). Refer to the mounting kit packing list for the required number of mounting clamps.
PPC-5xxx-9455 Panel PC Figure 4-21: Panel Mounting Clamp Positions Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 4-22).
PPC-5xxx-9455 Panel PC 4.7.3 Rack and Cabinet Installation To mount the PPC-5xxx-9455 into a rack/cabinet, please follow the steps below. NOTE: When purchasing the cabinet/rack installation bracket, make sure it is compatible with both the PPC-5xxx-9455 flat panel PC and the rack/cabinet into which the PPC-5xxx-9455 is installed. Step 1: Slide the rear of the PPC-5xxx-9455 panel PC through the rack/cabinet bracket until the aluminum frame is flush against the front of the bracket (Figure 4-23).
PPC-5xxx-9455 Panel PC Rack/Cabinet Bracket Figure 4-24: Secure the Rack/Cabinet Bracket Step 4: Slide the panel PC with the attached rack/cabinet bracket into a rack or cabinet (Figure 4-25).
PPC-5xxx-9455 Panel PC Step 5: Once the panel PC with the attached rack/cabinet bracket has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 4-25). 4.7.4 Arm Mounting The PPC-5xxx-9455 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 100 mm interface pad. To mount the PPC-5xxx-9455 on an arm, please follow the steps below. Step 1: The arm is a separately purchased item.
PPC-5xxx-9455 Panel PC Figure 4-26: Arm Mount Retention Screw Holes Step 4: Secure the PPC-5xxx-9455 to the interface pad by inserting four retention screws through the mounting arm interface pad and into the PPC-5xxx-9455 flat panel PC. Step 0: 4.8 External Peripheral Interface Connectors 4.8.1 LCD Panel Connection A conventional CRT VGA 15-pin female D-SUB connector is located on the bottom panel to connect the PPC-5xxx-9455 flat panel PC to a second monitor.
PPC-5xxx-9455 Panel PC 4.8.3 USB Connection The external peripheral interface USB connectors provide easy and quick access to external USB devices. The external peripheral interface USB connectors are a standard connector and can easily be connected to other USB devices. 4.8.4 Keyboard and Mouse Connection Two PS/2 connectors on the external peripheral interface panel facilitate the connection of a mouse and a keyboard.
PPC-5xxx-9455 Panel PC Chapter 5 5 BIOS Setup Page 69
PPC-5xxx-9455 Panel PC 5.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 5.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2.
PPC-5xxx-9455 Panel PC Key Function F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 5.1.
PPC-5xxx-9455 Panel PC 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS Menu 1: Main Î System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed.
PPC-5xxx-9455 Panel PC System Memory: Displays the auto-detected system memory. o Size: Lists memory size The System Overview field also has two user configurable fields: Î System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. Î System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 5.
PPC-5xxx-9455 Panel PC BIOS Menu 2: Advanced Page 74
PPC-5xxx-9455 Panel PC 5.3.1 CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configure the CPU.
PPC-5xxx-9455 Panel PC (HTT). If the operating system recognizes the installed processor, then this option should be kept in the default Disabled setting. Î Î Disabled Î Enabled DEFAULT CPUID is reported in full. Limits the maximum CPUID to 30h. Intel® SpeedStep® Technology [Enabled] The Intel® SpeedStep® Technology option allows the processor to use SpeedStep® if the processor supports it.
PPC-5xxx-9455 Panel PC 5.3.2 IDE Configuration Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration of the IDE devices installed in the system. BIOS Menu 4: IDE Configuration Î ATA/IDE Configurations [Enhanced] Use the ATA/IDE Configurations option to configure the ATA/IDE controller. Î Disabled Disables the on-board ATA/IDE controller. Î Compatible Configures the on-board ATA/IDE controller to be in compatible mode.
PPC-5xxx-9455 Panel PC Î Enhanced Configures the on-board ATA/IDE controller to be in DEFAULT Enhanced mode. In this mode, IDE channels and SATA channels are separated. Some legacy OS do not support this mode. Î Configure SATA as [IDE] The “Configure SATA as” option sets the configuration of the SATA ports.
PPC-5xxx-9455 Panel PC Primary IDE Master Primary IDE Slave The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the IDE devices installed in the system. If an IDE device is detected, and one of the above listed four BIOS configuration options are selected, the IDE configuration options shown in Section 5.3.2.1 appear. 5.3.2.
PPC-5xxx-9455 Panel PC Device: Lists the device type (e.g. hard disk, CD-ROM etc.) Type: Indicates the type of devices a user can manually select Vendor: Lists the device manufacturer Size: List the storage capacity of the device. LBA Mode: Indicates whether the LBA (Logical Block Addressing) is a method of addressing data on a disk drive is supported or not. Block Mode: Block mode boosts IDE drive performance by increasing the amount of data transferred.
PPC-5xxx-9455 Panel PC Î This option specifies an ATAPI Removable Media ARMD Device. These include, but are not limited to: ZIP LS-120 Î LBA/Large Mode [Auto] Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the maximum drive capacity is 137 GB. Î BIOS is prevented from using the LBA mode control on Disabled the specified channel.
PPC-5xxx-9455 Panel PC Î Auto DEFAULT BIOS auto detects the PIO mode. Use this value if the IDE disk drive support cannot be determined. Î 0 PIO mode 0 selected with a maximum transfer rate of 3.3 MB/s Î 1 PIO mode 1 selected with a maximum transfer rate of 5.2 MB/s Î 2 PIO mode 2 selected with a maximum transfer rate of 8.3 MB/s Î 3 PIO mode 3 selected with a maximum transfer rate of 11.1 MB/s Î 4 PIO mode 4 selected with a maximum transfer rate of 16.
PPC-5xxx-9455 Panel PC Î Ultra DMA mode 1 selected with a maximum data transfer UDMA1 rate of 25 MB/s Î Ultra DMA mode 2 selected with a maximum data transfer UDMA2 rate of 33.3 MB/s Î Ultra DMA mode 3 selected with a maximum data transfer UDMA3 rate of 44 MB/s (To use this mode, it is required that an 80-conductor ATA cable is used.) Î Ultra DMA mode 4 selected with a maximum data transfer UDMA4 rate of 66.6 MB/s (To use this mode, it is required that an 80-conductor ATA cable is used.
PPC-5xxx-9455 Panel PC 5.3.3 Floppy Configuration Use the Floppy Configuration menu (BIOS Menu 6) to configure the floppy disk drive connected to the system. BIOS Menu 6: IDE Master and IDE Slave Configuration Î Floppy A/B Use the Floppy A/B option to configure the floppy disk drive. Options are listed below: Page 84 Disabled 360 KB 51/4” 1.2 MB 51/4” 720 KB 31/2” 1.44 MB 31/2’ 2.
PPC-5xxx-9455 Panel PC 5.3.4 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 7) to set or change the configurations for the FDD controllers, parallel ports and serial ports. BIOS Menu 7: Super IO Configuration Î Digital I/O Address [2D8] Use the Digital I/O Address option to select the digital I/O port base address.
PPC-5xxx-9455 Panel PC Î Disabled Î 3F8/IRQ4 No base address is assigned to Serial Port 1 DEFAULT Serial Port 1 I/O port address is 3F8 and the interrupt address is IRQ4 Î 3E8/IRQ4 Serial Port 1 I/O port address is 3E8 and the interrupt address is IRQ4 Î 2E8/IRQ3 Serial Port 1 I/O port address is 2E8 and the interrupt address is IRQ3 Î Serial Port1 Mode [Normal] Use the Serial Port1 Mode option to select the transmitting and receiving mode for the first serial port.
PPC-5xxx-9455 Panel PC Î Î IrDA Serial Port 2 mode is IrDA Î ASK IR Serial Port 2 mode is ASK IR Parallel Port Address [Disabled] Use the Parallel Port Address option to select the parallel port base address.
PPC-5xxx-9455 Panel PC Î ECP+EPP The parallel port operates in the extended capabilities port (ECP) mode. The ECP mode supports bi-directional communication between the system and the parallel port device and the transmission rates between the two are much faster than the Normal mode The parallel port is also be compatible with EPP devices described above Î Parallel Port IRQ [IRQ7] Use the Parallel Port IRQ selection to set the parallel port interrupt address.
PPC-5xxx-9455 Panel PC Î Serial Port5 Address [2F0] Use the Serial Port5 IRQ option to select the interrupt address for serial port 5. Î Disabled No base address is assigned to serial port 5 Î 3E8 Serial port 5 I/O port address is 3E8 Î 2E8 Serial port 5 I/O port address is 2E8 Î 2F0 DEFAULT Î 2E0 Î Serial port 5 I/O port address is 2F0 Serial port 5 I/O port address is 2E0 Select RS232 or RS422/485 [RS/232] Use the Select RS232 or RS422/485 option to select the Serial Port 5 signaling mode.
PPC-5xxx-9455 Panel PC 5.3.5 Hardware Health Configuration The Hardware Health Configuration menu (BIOS Menu 8) shows the operating temperature, fan speeds and system voltages.
PPC-5xxx-9455 Panel PC Î CPU FAN 1 Mode Setting [Full On Mode] Use the CPU FAN 1 Mode Setting option to configure the CPU fan. Î Full On Mode Î DEFAULT Fan is on all the time FAN x Mode Setting [Automatic Mode] Use the FAN x Mode Setting option to configure the second fan. Î Full On Mode Î Automatic mode Fan is on all the time DEFAULT Fan is off when the temperature is low enough. Parameters must be set by the user.
PPC-5xxx-9455 Panel PC The CPU Temp. Limit of OFF option can only be set if the FAN x Mode Setting option is set to Automatic Mode. Use the CPU Temp. Limit of OFF option to select the CPU temperature at which the cooling fan should automatically turn off. To select a value, select the CPU Temp. Limit of OFF option and enter a decimal number between 000 and 127. The temperature range is specified below.
PPC-5xxx-9455 Panel PC The Temperature Limit of Full option can only be set if the FAN x Mode Setting option is set to Automatic Mode. Use the Temperature Limit of Full option to select the CPU temperature at which the cooling will reach full speed. To select a value, select the Temperature Limit of Full option and enter a decimal number between 000 and 127. The temperature range is specified below.
PPC-5xxx-9455 Panel PC The following system parameters and values are shown. The system parameters that are monitored are: System Temperatures: The following system temperatures are monitored o o o System Temperature 2 CPU Fan1 Speed Fan 1 Speed Fan 2 Speed Fan 3 Speed Voltages: The following system voltages are monitored o o o o o o o Page 94 System Temperature 1 Fan Speeds: The CPU cooling fan speed is monitored. o o o o CPU Temperature CPU Core +3.30 V +5.00 V +12.0 V +1.
PPC-5xxx-9455 Panel PC 5.3.6 Power Configuration The power configuration menu (BIOS Menu 9) sets the power features options. BIOS Menu 9: ACPI Configuration Î Power Supply Mode [ATX] Use the Power Supply Mode BIOS option to select the power supply that is connected to the system. Î An AT power supply is connected to the system and no AT power advanced power management features are enabled.
PPC-5xxx-9455 Panel PC 5.3.6.1 ACPI Configuration The ACPI Configuration menu (BIOS Menu 10) configures the Advanced Configuration and Power Interface (ACPI) and Power Management (APM) options. BIOS Menu 10: ACPI Configuration Î Suspend Mode [S3(STR)] Use the Suspend Mode option to specify the sleep state the system enters when it is not being used. Î S1 (POS) DEFAULT The system enters S1(POS) sleep state. The system appears off.
PPC-5xxx-9455 Panel PC 5.3.6.2 APM Configuration The APM Configuration menu (BIOS Menu 11) allows the advanced power management options to be configured. BIOS Menu 11:Advanced Power Management Configuration Î Power Button Mode [On/Off] Use the Power Button Mode BIOS to specify how the power button functions.
PPC-5xxx-9455 Panel PC Î Power Off The system remains turned off Î Power On The system turns on Î Last State DEFAULT The system returns to its previous state. If it was on, it turns itself on. If it was off, it remains off. Î Resume on Keyboard/Mouse [Disabled] Use the Resume on Keyboard/Mouse BIOS option to enable activity on either the keyboard or mouse to rouse the system from a suspend or standby state.
PPC-5xxx-9455 Panel PC Î Resume On RTC Alarm [Disabled] Use the Resume On RTC Alarm option to specify the time the system should be roused from a suspended state. Î Disabled DEFAULT The real time clock (RTC) cannot generate a wake event Î Enabled If selected, the following appears with values that can be selected: RTC Alarm Date (Days) System Time After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off.
PPC-5xxx-9455 Panel PC 5.3.7 Remote Access Configuration Use the Remote Access Configuration menu (BIOS Menu 12) to configure remote access parameters. The Remote Access Configuration is an AMIBIOS feature and allows a remote host running a terminal program to display and configure the BIOS settings. BIOS Menu 12: Remote Access Configuration [Advanced] Î Remote Access [Disabled] Use the Remote Access option to enable or disable access to the remote functionalities of the system.
PPC-5xxx-9455 Panel PC Î Remote access configuration options shown below Enabled appear: Serial Port Number Serial Port Mode Flow Control Redirection after BIOS POST Terminal Type VT-UTF8 Combo Key Support These configuration options are discussed below. Î Serial Port Number [COM1] Use the Serial Port Number option allows to select the serial port used for remote access.
PPC-5xxx-9455 Panel PC NOTE: Identical baud rate setting musts be set on the host (a management computer running a terminal software) and the slave Î Redirection After BIOS POST [Always] Use the Redirection After BIOS POST option to specify when console redirection should occur.
PPC-5xxx-9455 Panel PC 5.3.8 USB Configuration Use the USB Configuration menu (BIOS Menu 13) to read USB configuration information and configure the USB settings. BIOS Menu 13: USB Configuration Î USB Configuration The USB Configuration field shows the system USB configuration. The items listed are: Î Module Version: x.xxxxx.
PPC-5xxx-9455 Panel PC Î Î Disabled Î Enabled USB function support disabled DEFAULT USB function support enabled USB 2.0 Controller [Enabled] Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller Î Î Disabled Î Enabled USB 2.0 controller disabled DEFAULT USB 2.0 controller enabled Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support.
PPC-5xxx-9455 Panel PC 5.3.8.1 USB Mass Storage Device Configuration Use the USB Mass Storage Device Configuration menu (BIOS Menu 14) to configure USB mass storage class devices. BIOS Menu 14: USB Mass Storage Device Configuration Î USB Mass Storage Reset Delay [20 Sec] Use the USB Mass Storage Reset Delay option to set the number of seconds POST waits for the USB mass storage device after the start unit command.
PPC-5xxx-9455 Panel PC Î POST waits 40 seconds for the USB mass storage 40 Sec device after the start unit command. Î Device ## The Device## field lists the USB devices that are connected to the system. Î Emulation Type [Auto] Use the Emulation Type BIOS option to specify the type of emulation BIOS has to provide for the USB device. NOTE: Please note that the device’s formatted type and the emulation type provided by the BIOS must match for a device to boot properly.
PPC-5xxx-9455 Panel PC Î CDROM Assumes the CD-ROM is formatted as bootable media. All the devices that support block sizes greater than 512 bytes can only be booted using this option. 5.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 15) to configure advanced PCI and PnP settings. WARNING! Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction.
PPC-5xxx-9455 Panel PC Î IRQ# [Available] Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral device.
PPC-5xxx-9455 Panel PC Î DM Channel 5 DM Channel 6 DM Channel 7 Reserved Memory Size [Disabled] Use the Reserved Memory Size BIOS option to specify the amount of memory that should be reserved for legacy ISA devices. Î Disabled Î 16K 16 KB reserved for legacy ISA devices Î 32K 32 KB reserved for legacy ISA devices Î 64K 54 KB reserved for legacy ISA devices DEFAULT No memory block reserved for legacy ISA devices 5.
PPC-5xxx-9455 Panel PC 5.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 17) to configure advanced system boot options. BIOS Menu 17: Boot Settings Configuration Î Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process.
PPC-5xxx-9455 Panel PC Î Î Enabled DEFAULT OEM Logo displayed instead of POST messages AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Î Force BIOS DEFAULT The system forces third party BIOS to display during system boot. Î The system displays normal information during Keep Current system boot.
PPC-5xxx-9455 Panel PC Î Enabled DEFAULT Can be booted from a remote system through the LAN 5.5.2 Boot Device Priority Use the Boot Device Priority menu (BIOS Menu 18) to specify the boot sequence from the available devices. Possible boot devices may include: HDD CD/DVD USB BIOS Menu 18: Boot Device Priority Settings 5.5.3 Hard Disk Drives Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs.
PPC-5xxx-9455 Panel PC 3rd Drive [HDD: SM-(part number)] 4th Drive [HDD: SM-(part number)] NOTE: Only the drives connected to the system are shown. For example, if only two HDDs are connected only “1st Drive” and “2nd Drive” are listed. The boot sequence from the available devices is selected. If the “1st Drive” option is selected a list of available HDDs is shown. Select the first HDD the system boots from. If the “1st Drive” is not used for booting this option may be disabled.
PPC-5xxx-9455 Panel PC 5.5.4 CD/DVD Drives Use the CD/DVD Drives menu to specify the boot sequence of the available CD/DVD drives. When the menu is opened, the CD drives and DVD drives connected to the system are listed as shown below: 1st Drive [CD/DVD: PM-(part ID)] 2nd Drive [HDD: PS-(part ID)] 3rd Drive [HDD: SM-(part ID)] 4th Drive [HDD: SM-(part ID)] NOTE: Only the drives connected to the system are shown.
PPC-5xxx-9455 Panel PC BIOS Menu 20: CD/DVD Drives Page 115
PPC-5xxx-9455 Panel PC 5.6 Security Use the Security menu (BIOS Menu 21) to set system and user passwords. BIOS Menu 21: Security Î Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password.
PPC-5xxx-9455 Panel PC 5.7 Chipset Use the Chipset menu (BIOS Menu 22) to access the Northbridge and Southbridge configuration menus WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.
PPC-5xxx-9455 Panel PC 5.7.1 Northbridge Configuration Use the Northbridge Configuration menu (BIOS Menu 22) to configure the Northbridge chipset. BIOS Menu 23:Northbridge Chipset Configuration Î Memory Hole [Disabled] Use the Memory Hole option to reserve memory space between 15 MB and 16 MB for ISA expansion cards that require a specified area of memory to work properly.
PPC-5xxx-9455 Panel PC Î Boot Display Device Use the Boot Display Device option to select the display device used by the system when it boots. Configuration options are listed below. Î Auto CRT - Default TV LFP CRT + LFP Flat Panel Type [By Jumper] Use the Flat Panel Type is set using the onboard jumper settings. The jumper settings can be found in the Installation and Configuration chapter.
PPC-5xxx-9455 Panel PC 5.7.2 Southbridge Configuration The Southbridge Configuration menu (BIOS Menu 24) allows the Southbridge chipset to be configured. BIOS Menu 24:Southbridge Chipset Configuration Î Spectrum [Disabled] Use the Spectrum option to reduce the EMI. Excess EMI is generated when the system clock generator pulses have extreme values. Spreading the pulse spectrum modulates changes in the extreme values from spikes to flat curves, thus reducing the EMI.
PPC-5xxx-9455 Panel PC Î Audio Controller [Azalia] Use the Audio Controller Selection option to enable or disable the High Definition Audio CODEC. Î Disabled Î Azalia The onboard HD Audio is disabled DEFAULT The onboard HD Audio is enabled 5.8 Exit Use the Exit menu (BIOS Menu 25) to load default BIOS values, optimal failsafe values and to save configuration changes.
PPC-5xxx-9455 Panel PC Î Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system. Î Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program. Î Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of the parameters on the Setup menus. F9 key can be used for this operation.
PPC-5xxx-9455 Panel PC Chapter 6 6 Software Installation Page 123
PPC-5xxx-9455 Panel PC 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. You may visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system. Chipset driver VGA driver Gigabit Ethernet driver Audio Driver Installation instructions are given below. 6.
PPC-5xxx-9455 Panel PC Figure 6-1: Chipset Driver Installation Program Step 2: Double-click the infinst_Autol.exe icon. Step 3: The welcome screen in Figure 6-2 appears. Figure 6-2: Chipset Driver Installation Welcome Screen Step 4: Click NEXT to continue the installation process. Step 5: The license agreement in Figure 6-3 appears.
PPC-5xxx-9455 Panel PC Figure 6-3: Chipset Driver Installation License Agreement Step 6: Read the license agreement. To accept the terms and conditions stipulated in the agreement, click YES. Step 7: The Readme file in Figure 6-4 appears.
PPC-5xxx-9455 Panel PC Step 8: Read the Readme file information and then click NEXT to start the driver installation. Step 9: The Setup Progress windows appears (Figure 6-5). Figure 6-5: Chipset Driver Installation Complete Step 10: After the driver installation process is complete click NEXT to continue Step 11: The Setup is Complete windows appears (Figure 6-6).
PPC-5xxx-9455 Panel PC Figure 6-6: Chipset Driver Installation Complete Step 12: The computer must be restarted for changes to take effect. Select “Yes, I want to restart this computer now,” to restart the computer when finished, or “No, I will restart this computer later,” to manually restart the computer later. Click FINISH to complete the driver installation. Step0: 6.3 Graphics Driver To install the graphics driver, please follow the steps below.
PPC-5xxx-9455 Panel PC Figure 6-7: Graphics Setup Icon Step 2: Double-click the setup icon to start the graphics driver installation (Figure 6-7). Step 3: A new window appears with a detailed explanation of what is contained in the graphics driver file (Figure 6-8). Figure 6-8: VGA Driver Step 4: Click NEXT to continue the driver installation process (Figure 6-8).
PPC-5xxx-9455 Panel PC Step 5: The Graphics driver welcome screen appears (Figure 6-9). Figure 6-9: Graphics Driver Installation Step 6: Click NEXT to continue the driver installation (Figure 6-9). Step 7: The license agreement appears (Figure 6-10).
PPC-5xxx-9455 Panel PC Step 8: Read the license agreement carefully. Click YES to accept the terms of the license agreement and continue installation. Step 9: A new window appears with details of the drivers to be installed (Figure 6-11). Figure 6-11: Graphics Driver Readme file Step 10: Click NEXT to start installing the graphics drivers.
PPC-5xxx-9455 Panel PC Step 11: The driver installation progress window appears and shows details for each of the drivers as they are installed (Figure 6-12). Figure 6-12: Graphics Driver Installation Notice Step 12: The Setup is Complete window appears. (Figure 6-13).
PPC-5xxx-9455 Panel PC Step 13: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer. Step 0: 6.4 Gigabit Ethernet Driver Installation To install the Gigabit Ethernet driver, please follow the steps below. Step 1: Open Windows Control Panel (Figure 6-14). Figure 6-14: Windows Control Panel Step 2: Double-click the System icon (Figure 6-15).
PPC-5xxx-9455 Panel PC Figure 6-15: System Icon Step 3: Select the Hardware tab and click the DEVICE MANAGER tab (Figure 6-16).
PPC-5xxx-9455 Panel PC Step 4: Right-click the “Ethernet Controller” and select “Update Driver…” to start the driver update process (Figure 6-17). Figure 6-17: Device Manager List Step 5: The Device Driver Wizard appears (Figure 6-18).
PPC-5xxx-9455 Panel PC Step 6: Select “No, not this time” to force the wizard to search hard drives, CD drives and floppy drives for a driver and not connect to the Internet to search for the appropriate driver (Figure 6-18). Step 7: The automatic driver search prompt appears (Figure 6-19). Figure 6-19: Search Windows Update Prompt Step 8: Select “Install the software automatically (Recommended),” and click NEXT to continue (Figure 6-19).
PPC-5xxx-9455 Panel PC Step 9: After the installation wizard finds the Gigabit Ethernet driver, the Hardware Update Completed window appears (Figure 6-20). Figure 6-20: Hardware Installation Complete Step 10: Click FINISH to exit the installation wizard and complete the installation process. Step0: 6.5 Audio Driver To install the audio driver, the audio needs to be enabled in the BIOS and then the software driver can be installed. 6.5.1 BIOS Setup Step 1: Enter the BIOS setup.
PPC-5xxx-9455 Panel PC 6.5.2 Driver Installation To install the audio driver please follow the steps below. Step 1: Browse to the 2-Audio\ALC888-5614_PG258_UAAV10a-5013 folder on the installation CD (Figure 6-21). Figure 6-21: Select the Audio Codec Step 2: Double-click the Setup icon. Step 3: The audio setup window appears (Figure 6-22).
PPC-5xxx-9455 Panel PC Step 4: Click NEXT to start the driver installation (Figure 6-22). Step 5: The audio driver installation begins. Step 6: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer. Step0: Figure 6-23: InstallShield Wizard Complete 6.6 Touch Panel Driver To install the touch panel driver, please follow the steps below.
PPC-5xxx-9455 Panel PC Step 1: Browse to the Touch directory on the installation CD (Figure 6-24). Figure 6-24: S-Video Patch Folder Step 2: Double-click the setup icon (Figure 6-24). Step 3: A new window opens and the touch panel driver installation wizard is shown (Figure 6-25). Figure 6-25: Touch Panel Driver Welcome Screen Step 4: Click NEXT to begin the touch panel driver installation process (Figure 6-25). Step 5: The license agreement window appears (Figure 6-26).
PPC-5xxx-9455 Panel PC Figure 6-26: Touch Panel License Agreement Step 6: Read the license agreement carefully. Click I AGREE to accept the terms of the agreement and proceed with the installation (Figure 6-26). Step 7: The Choose Installation Location window appears (Figure 6-27).
PPC-5xxx-9455 Panel PC Step 8: Accept the default installation directory (only change if necessary) then click INSTALL to install the touch panel drivers (Figure 6-27). Step 9: The touch panel driver begins installing (Figure 6-28). Figure 6-28: Touch Panel Drivers Installing Step 10: The Windows logo testing warning screen is shown. The warning explains that the software has not passed Windows logo testing.
PPC-5xxx-9455 Panel PC Figure 6-30: InstallShield Wizard Complete Step 12: Click FINISH to complete the installation process and exit the touch panel driver installation program (Figure 6-30).
PPC-5xxx-9455 Panel PC Chapter 7 7 System Maintenance Page 144
PPC-5xxx-9455 Panel PC 7.1 System Maintenance Introduction The following system components may require maintenance. Motherboard DIMM module PSU module Cooling fans If these components fail, they must be replaced. Please contact the system reseller or vendor to purchase replacement parts. Replacement instructions for the above listed components are described below. 7.2 Motherboard Replacement A user cannot replace a motherboard.
PPC-5xxx-9455 Panel PC WARNING! Please take antistatic precautions when working with the internal components. The interior of the PPC-5xxx-9455 contains very sensitive electronic components. These components are easily damaged by electrostatic discharge (ESD). Before working with the internal components, make sure all anti-static precautions described earlier have been observed. To access the panel PC internal components, the back cover must be removed.
PPC-5xxx-9455 Panel PC Figure 7-1: DIMM Socket Clip Locations Step 3: Push the new DIMM module until it engages and the white plastic end clips click into place. Make sure the end clips are fully secured after installation. Step 0: 7.5 Elevated Platform Removal The elevated platform supports the optical drive and the hard drive. It is not necessary to remove the optical drive bracket or hard drive bracket to remove the elevated platform.
PPC-5xxx-9455 Panel PC Step 2: Unfasten the elevated platform screws on the side panel (Figure 7-3). Figure 7-3: Side Panel Elevated Platform Screws Step 3: Unfasten the elevated platform screws on the bottom panel (Figure 7-4).
PPC-5xxx-9455 Panel PC Step 4: Unfasten the internal elevated platform screws (Figure 7-5). Figure 7-5: Internal Elevated Platform Screws Step 5: Slide the elevated platform out of the chassis. Step 0: 7.6 PSU Module Replacement Please read the warnings at the beginning of Section 4.3 before attempting to access any PPC-5xxx-9455 internal components. If the PSU module has been damaged it must be replaced. To replace the PSU module, please follow the steps below. 7.6.
PPC-5xxx-9455 Panel PC Step 3: Disconnect all PSU connections including those to the motherboard (Figure 7-6) and any disk drives. Figure 7-6: PSU Power Cables Step 4: Unfasten the screws on the inside panel (Figure 7-7).
PPC-5xxx-9455 Panel PC Step 5: Remove the retention screws that connect the PSU bracket to the chassis (Figure 7-8). Figure 7-8: PSU Rear Panel Screws Step 6: Remove the retention screws that connect the PSU to the PSU bracket.Step 0: 7.6.2 Install the New PSU Installation is done in the reverse order to removal. To install a new PSU module, please follow the steps below. Step 1: Attach the PSU bracket to the PSU module with the previously removed retention screws.
PPC-5xxx-9455 Panel PC 7.7 System Cooling Fan Replacement If the system cooling fans have been damaged, they must be replaced. To replace the system cooling fans, please follow the steps below. 7.7.1 Remove the Old System Cooling Fans Step 1: Remove the back cover (Section 4.4). Step 2: Detach and remove the elevated platform (Section 7.5). Step 3: Disconnect the system cooling fans from the motherboard (Figure 7-9).
PPC-5xxx-9455 Panel PC Step 4: Remove the system cooling fans retention screws from the left panel (Figure 7-10). Figure 7-10: System Cooling Fans Left Panel Retention Screws Step 5: Remove the system cooling fans from the chassis. Step 0: 7.7.2 Install the New System Cooling Fans To install the new system cooling fans, please follow the steps below. Step 1: Insert the system cooling fans into the chassis and attach to the left panel with the previously removed retention screws.
PPC-5xxx-9455 Panel PC Appendix A A BIOS Options Page 154
PPC-5xxx-9455 Panel PC Below is a list of BIOS configuration options in the BIOS chapter. System Overview .................................................................................................................72 System Time [xx:xx:xx] .......................................................................................................73 System Date [xx/xx/xx] ........................................................................................................
PPC-5xxx-9455 Panel PC FAN x Mode Setting [Automatic Mode] .............................................................................91 Temperature Limit of OFF [025] .........................................................................................91 Temperature Limit of Start [025] ........................................................................................92 Temperature Limit of Full [080] ..........................................................................................
PPC-5xxx-9455 Panel PC Boot From LAN Support [Disabled] ................................................................................ 111 Change Supervisor Password ......................................................................................... 116 Change User Password.................................................................................................... 116 Memory Hole [Disabled] ...................................................................................................
PPC-5xxx-9455 Panel PC Appendix B B Terminology Page 158
PPC-5xxx-9455 Panel PC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
PPC-5xxx-9455 Panel PC DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. DIO The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
PPC-5xxx-9455 Panel PC LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on.
PPC-5xxx-9455 Panel PC Appendix C C Digital I/O Interface Page 162
PPC-5xxx-9455 Panel PC C.1 Introduction The DIO connector on the PPC-5xxx-9455 is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions. NOTE: For further information, please refer to the datasheet for the Super I/O chipset. C.
PPC-5xxx-9455 Panel PC C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. MOV AX, 6F08H Sets the digital port as input INT 15H Initiates the INT 15H BIOS call C.3.2 Enable the DIO Output Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O output functions is listed below.
PPC-5xxx-9455 Panel PC Appendix D D Watchdog Timer Page 165
PPC-5xxx-9455 Panel PC NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
PPC-5xxx-9455 Panel PC NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
PPC-5xxx-9455 Panel PC Appendix E E Address Mapping Page 168
PPC-5xxx-9455 Panel PC E.
PPC-5xxx-9455 Panel PC E.
PPC-5xxx-9455 Panel PC Figure E-3: Input/Output (IO) (2 of 2) Page 171
PPC-5xxx-9455 Panel PC E.
PPC-5xxx-9455 Panel PC E.
PPC-5xxx-9455 Panel PC Appendix F F Compatibility Page 174
PPC-5xxx-9455 Panel PC NOTE: The compatible items described here have been tested by the IEI R&D team and found to be compatible with the PPC-5xxx-9455 F.1 Compatible Operating Systems The following operating systems have been successfully run on the PPC-5xxx-9455. MS-DOS 6.22 Microsoft Windows XP (32-bit) Microsoft Windows 2000 Red Hat 9.0 F.
PPC-5xxx-9455 Panel PC F.3 Compatible Memory Modules NOTE: The memory modules listed below have been tested on the PPC-5xxx-9455 other memory modules that comply with the specifications may also work on the PPC-5xxx-9455 but have not been tested. The following memory modules have been successfully tested on the PPC-5xxx-9455. Manufacturer Transcend Page 176 Model 507303-0233 Capacity 1.
PPC-5xxx-9455 Panel PC Appendix G G Hazardous Materials Disclosure Page 177
PPC-5xxx-9455 Panel PC G.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
PPC-5xxx-9455 Panel PC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X X O O O O O X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O: This toxic or haza
PPC-5xxx-9455 Panel PC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 (Pb) (Hg) (Cd) (CR(VI)) (PBB) 醚 (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以
