Owner manual

ManualsBrandsIEI Integration ManualsComputersPPC-5xxx-9455 v1.00

Table Of Contents

Revision
Copyright
Manual Conventions
Packing List
Table of Contents
List of Figures
List of Tables
BIOS Menus
1 Introduction
- 1.1 General Overview
- 1.2 External Overview
- 1.3 Internal Overview
2 Specifications
- 2.1 Introduction
- 2.2 Dimensions
- 2.3 Motherboard
- 2.4 CPU Support
- 2.5 System Chipsets
  - 2.5.1 Intel® 945G Northbridge Chipset
  - 2.5.2 ICH7 Southbridge Chipset
- 2.6 Graphics Support
  - Analog CRT Support
  - 2.6.2 LVDS Support
- 2.7 Memory
- 2.8 Storage
  - CompactFlash®
  - 2.8.2 SATA Hard Drive
- 2.9 Expansion Slots
- 2.10 External Device Connectors
- 2.11 Gigabit Ethernet
- 2.12 Front Panel
  - 2.12.1 Flat Screen
  - 2.12.2 Touch Screen
- 2.13 OEM Options
3 Unpacking
- 3.1 Anti-static Precautions
- 3.2 Unpacking Precautions
- 3.3 Package Contents
4 Installation and Configuration
- 4.1 Installation Precautions
- 4.2 Preinstalled Components
- 4.3 Installation and Configuration Steps
- 4.4 Remove the Back Cover
- 4.5 Jumper Settings
- 4.6 Drive Installation
- 4.7 Mounting the System
- 4.8 External Peripheral Interface Connectors
5 BIOS Setup
- 5.1 Introduction
- 5.2 Main
- 5.3 Advanced
- 5.4 PCI/PnP
- 5.5 Boot
- 5.6 Security
- 5.7 Chipset
  - 5.7.1 Northbridge Configuration
  - 5.7.2 Southbridge Configuration
- 5.8 Exit
6 Software Installation
- 6.1 Available Software Drivers
- 6.2 Chipset Driver
- 6.3 Graphics Driver
- 6.4 Gigabit Ethernet Driver Installation
- 6.5 Audio Driver
  - 6.5.1 BIOS Setup
  - 6.5.2 Driver Installation
- 6.6 Touch Panel Driver
7 System Maintenance
- 7.1 System Maintenance Introduction
- 7.2 Motherboard Replacement
- 7.3 Back Cover Removal
- 7.4 DIMM Replacement
- 7.5 Elevated Platform Removal
- 7.6 PSU Module Replacement
  - 7.6.1 Remove the Old PSU
  - 7.6.2 Install the New PSU
- 7.7 System Cooling Fan Replacement
  - 7.7.1 Remove the Old System Cooling Fans
  - 7.7.2 Install the New System Cooling Fans
A BIOS Options
B Terminology
C Digital I/O Interface
- C.1 Introduction
- C.2 DIO Connector Pinouts
- C.3 Assembly Language Samples
  - C.3.1 Enable the DIO Input Function
  - C.3.2 Enable the DIO Output Function
D Watchdog Timer
E Address Mapping
- E.1 Direct Memory Access (DMA)
- E.2 Input/Output (IO)
- E.3 Interrupt Request (IRQ)
- E.4 Memory
F Compatibility
- F.1 Compatible Operating Systems
- F.2 Compatible Processors
- F.3 Compatible Memory Modules
G Hazardous Materials Disclosure
- G.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury
Index

PPC-5xxx-9455 Panel PC

Page 46

4.5.6.3 COM5 D-Sub Pinout Selection (J4)

Jumper J4 sets the external COM5 serial port as RS-232 or RS-422/485.

J4 DESCRIPTION

1-2, 4-5, 7-8, 10-11 RS-232

2-3, 5-6, 8-9, 11-12 RS-422/485

Table 4-14: COM5 RS-422/485 TX Select

4.5.6.4 COM5 Termination Resistors (J5, J6)

The termination resistors J5 and J6 can remedy communication errors for RS-422/485

setups with cables over 1.5 km in length

J5 J6 DESCRIPTION

Open Open No terminator resistor set

Closed Closed Termination resistor set

Table 4-15: COM5 RS-422/485 TX Select

4.5.7 LCD Voltage Settings (JP9)

WARNING:

Do not change these settings. They are set for the installed LCD panel.

Using different settings on the preinstalled monitor can destroy it.

The LCD setup sets the voltage and default monitor settings on the PPC-5xxx-9455.

JP9 LCD Voltage

1-2 3.3 V

3-4 5 V

5-6 12 V

Table 4-16: LCD Voltage Settings